TiE Onyx 2, 3, 4, 5 Service And Programming Manual

 EXTENSIONS
 HUNT TYPE
 HUNTING OPERATIONAL  (Page  of 6)
TYPE OF 
CONDITION
D I D Bus];Skip member. If  busy.intercept or  tone.Skip member. If all busy. Skip member. If  busy.intercept or  tone.
intercept or  tone.
Ring  No answer
Ring.  to end Ring.  to end Ring. cycle to end
of group. then  Ring. of group. then  Ring.of group. then  Ring.
Voice call 
 No answer N/AN/A
D.N.D.
Skip member. Skip member. Skip member,if all DND intercept. if all DND intercept. if all DND intercept.
Call Forwarded
Follows...

E- EXTENSIONS
 HUNT TYPE
EXTENSION HUNTING   (Page 5 of 6)
 CONDITION 
TransferedSkip member. If all Skip member. If all busy. Skip member. If all busy.trunk
Camp-On for 1st free hold” msg. Camp-On hold” msg. Camp-On
member. then overflow. for  free member. thenfor 1st free member. thenthen  Ring.
overflow. then Key Ring. ovefflow. then Key Ring.
Ring 
 No answerCycles UCD group queue. Cycles UCD group queue. Cycles UCD group queue.
Voice call  No answer 
D.N.D.Treat as busy. Treat as busy. Treat as...

E- EXTENSIONS
 HUNT TYPE
 HUNTING   (Page 6 of 
 
DIDSkip member. If all bus!.
busy tone.
Ring 
 No answer UCD group.
Voice call 
 No answer 
D.N.D.Treated as busy.
Call 
Follows Call  ard.
DISA
Busy
Skip member. If all
busy. busy tone.
Ring 
 No Cycle UCD group.
Skip member. If all busy. Skip member. If all busy. hold” msg. hold” msg.
then overflow.then overflow.
Cycle  UCD  group. Cycle UCD group queue.
Treated as busy. Treated as busy.
Follows Call Forward. Follows Call 
Skip member. If all Skip...

E- EXTENSIONS
 HUNT TYPE
Related
Programming
 The ACD group master extension
l Reset Queues  Reset the system queues after initial ACD
programming.
Extension Hunting, Circular and Terminal
lE- Extensions,  Next Extension in Hunt Group  Use this option to link
extensions into a hunting list. For Circular Hunting, make sure your last
member loops back to the first.For Terminal Hunting, enter 
 for the last
member.
Automatic Call Distribution
CP- ACD Supervisor 
   Set the Supervisor  bit for the...

E- EXTENSIONS
ES- HUNT TYPE
Related
Programming
(Cont’d)
l
l
l
l
l
Feature Reference
Instructions
Step  
Step 1 
Step 2 
Step 3 
 Reset System Queues  Reset the system queues after installing the
Voice Messagmg System.
 Reset VX Flag (Telephone Message Waiting Lamps)  For a first
time installation, always use this option to reset the telephone Message
Waiting lamps.
KS- Programming Keys for 
  Designate a programmable key as a
Record key (type R).
QP- Voice Mailbox Installation, Mailbox Installed...

E- EXTENSIONS
 DATA SET
Description
Related
Programming
Feature Reference
Instructions
Step 1 
Step 1 
Step 2 
Step 3 
Use this option to assign a Data Set or a Data Module with a bridged 
For extensions that are not Data Sets or bridged to Data Modules, always
disable this option. When programming Data Sets or Data Modules, refer to
the Data Products Manual. This option applies to 
 and Data Sets only.
Conditions
None
Default Value
Extension is not a Data Set (N).
Refer to the Data Products Manual....

E- EXTENSIONS
 PAGE ZONE
Description
Related
Programming
l
l
l
l
l
Issue 1-O
Use this option to assign a   set or Data Set to an Internal Paging
zone. The internal zones are:
00 All Call Paging only
01Internalzone1
02Internalzone2
03Internalzone3
04Internalzone4
05
Internalzone5
06Internalzone6
07Internalzone7
For example, you can assign extension 304 to internal zone 5 (05). The
speaker in extension 304 only broadcasts zone 5 and All Call Paging
announcements.
Conditions
None
Default Value
Extension...

E- EXTENSIONS
 PAGE ZONE
l
l
l
l
l
Feature Reference
Instructions
To enter data on the PRF:
Step  lEnter the Paging zone number (00-07) for each extension on Table 3.
Step 1 l
Step 2 
To enter data at  programming terminal:
Type E3. You see:  
Press RETURN to program extension 
OR
Enter another extension number and press RETURN. In either case, you see:
PAGE ZONE
Step 3 Enter data for this option from Table 3 and press RETURN.You advance to the next consecutive extension.
Tenant Service, Assigning...

E- EXTENSIONS
 LINE ACCESS OPTIONS, RINGING LINE PREFERENCE
Description
Related
Programming
l
Feature Reference
Instructions
Step 
Step 
Step  
Step 3 
Use this option to allow or deny Ringing Line Preference at each  This
option applies to all trunk calls ringing the extension (not Intercom calls).
Conditions
Intercom calls to an attendant follow  Ringing Line Preference
programming.
Default Value
Ringing Line Preference disabled (N).
Ringing Line Preference
KS- Programming 
 for   Program the line and...

E- EXTENSIONS
ES- LINE ACCESS OPTIONS, OFF-HOOK RINGING
Description
Related
Programming
Feature Reference
Instructions
Step 1 l
. Step 1 l
Step 2 l
Use this option to enable/disable incoming off-hook ring for a  Keep
in mind that this option interacts with EF- Incoming Voice Over Off-Hook
Signals. The chart below shows 
this interaction for the destination extension.
 CallerDest. EFResult after dialing 1
 HandsetHandset
N NVoice Over to destination
 HandsetHandsfree NNo Off-Hook Signaling
 Handsfree...