TiE Onyx 2, 3, 4, 5 Service And Programming Manual

C- CLASS OF SERVICE
CP- 
ALLOW ONLY LOCAL CALLS AT NIGHT 
Description
Related
Programming
l
l
l
l
l
Use this option to restrict extensions  this COS to Intercom and-local calls
in the night mode. This option also applies to DISA trunks and incoming tie
trunks. This assignment overrides AP programming (except AP- Allow
Active Dial Pad).
If you enable this option (1). estension users can only place the 
types of trunk calls:
 7-digit  calls.   digit 2-9
  1 and 911 calls
  calls
If disabled (0). this...

C- CLASS OF SERVICE
CP- ALLOW ONLY LOCAL CALLS AT 
 
Related
Programming
(Cont’d)
l
l
Feature Reference
Instructions
Step 1 l
E- Extensions.  Class of Service  Assign Class of Service to extensions.
E- Trunks, EJ- Toll Restriction 
 Enable/disable Toll Restriction for each
trunk.
Toll Restriction
To enter data on the PRF:
On Table 
 for BY I  enter 0 not to limit extensions to local calls at night-.
Enter 1 to restrict estensions to local calls at night.
To enter data at the programming terminal:
Type...

C- CLASS OF SERVICE
CP- ALLOW ONLY LOCAL 
 (DAY OR NIGHT) 
Description
Related
Programming
l
l
l
Use this option to restrict extensions  this COS to Intercom and local
calls. This option also applies to 
 trunks and incoming tie trunks. This
assignment overrides AP programming (except AP- Allow Active Dial Pad).
If you enable this option (1). extension users can only place the following
 of trunk calls:
 7-digit  calls.   digit 2-9
  and 91  calls
  calls
If disabled (0). this option does not restrict...

 CLASS OF 
CP- ALLOW ONLY LOCAL CALLS  OR NIGHT) 
Feature Reference
Instructions
Step 1 
Step 1 
Step  
 Estensions.  Class of Service  Assign Class of Service to extensions.
E- Trunks, EJ- Toll Restriction 
  Toll Restriction for each
trunk.
Toll Restriction
To enter data on the PRF:
On Table 2 for BY 
 enter 0 not to limit extensions to local calls. Enter 1 to
restrict extensions to local calls at night.
To enter data at the programming terminal:
Type CP. You see: 
COS  00: 00010000  00000001
Enter...

C- CLASS OF SERVICE
CP- 
 TOLL RESTRICTION LEVEL 
Description
Related
Programming
l
l
l
l
l
issue 1-OSOFTWARE CONFIGURATION 2-57
 this option  assign a  Restriction level (l-7) to extensions-with this
COS. This option 
 applies to  trunks and incoming tie trunks. 
 assign toll   to COS  (for attendants).
This option does not  to CO lines.
Default  
No restriction (toll level 0).
Equal Access 
AP- Allow Equal Access For each Toll Restriction Level, allow Equal
Access 
 and program the Equal Access Code...

C- CLASS OF SERVICE
 EXTENSION TOLL RESTRICTION  
l
l
l
l
Feature Reference
Instructions
Step 1 
Step I l
Step  
Toll Restriction 
  Allow SP.4 Dialing   area code (NPA) dialing for this
Toll 
 Also. program the  codes table.
  Digit Analysis   analysis for this Toll Level.
Also. program a sis-digit analysis table.
CP- Allow 
 Intercom Calls at Night   At night, extensions
with this option enabled can 
 place Intercom calls. This assignment
overrides AP programming.
CP- Allow Only Local Calls at Night...

C- CLASS OF SERVICE
 SINGLE RING OPX 
Description
Related
Programming
Feature Reference
Instructions
Step 1 
Step 1 l
Step  
Issue 1-O
Use this option to enable (0) or disable  Distinctive Ringing for ports with
circuit types 
 and   (OPX and  extensions). If enabled  trunk calls
have two short rings (repeated) 
  a pause. Intercom calls have a
single one second ring 
  a pause. If disabled (1). Intercom and
trunk calls have a single one second ring 
  a pause.
In ONYX IV. this option is CP- Long Ring...

C- CLASS OF SERVICE
CP- INHIBIT FLASH FOR SINGLE LINE TELEPHONES 
Description
Related
Programming
l
Feature Reference
Instructions
Step 
 
Step  l
Step 2 
Use this option to enable (0) or disable  Flash for ESL sets with this 
 enabled. ESL  can  and release the  to Flash a trunk.
  are using  to assign an  supervisor  go to CP- ACD
   on the nest page.
None
 
Flash allowed at ESL sets (0).
Flash
 Extensions,   Class of Service  Assign Class of  to extensions.
QT- System Timers,  Flash Response Time...

C- CLASS OF SERVICE
CP- ACD SUPERVISOR 
 
Description
Related
Programming
Feature Reference
Instructions
Step  
  l
Step 2 l
Use this option to assign extensions  this COS as ACD supervisor
 This option only identifies the extension as a supervisor. It does not
 the  to an ACD group (see Related Programming below). If
enabled (I). extension is an ACD supervisor.If disabled 
 extension is not
a supervisor.
None
Default 
ACD supervisor not assigned (0).
Automatic Call Distribution
E- Extensions, 
 Circuit...

 CLASS OF 
CP-  SILENT  
Description
Related
Programming
l
l
Feature Reference
Instructions
Step  l
Step 1 
Step 2 l
Use this option to allow  or  (0) Silent with this COS from initiating
Silent Monitor.
None
Default 
Silent Monitor not allowed (0).
Silent Monitor
E- Estensions, 
 Class of  Service  Assign Class of Service to extensions.
E- Extensions. EC- Group Call Pickup Group 
 Assign the Group Call
Pickup number to extensions (0 I-23. 00 for no group).
Silent Monitor
To enter data on the PRF:
On...