TiE Onyx 2, 3, 4, 5 Service And Programming Manual

A- TOLL RESTRICTION
AP- TOLL RESTRICTION 
 For   
  

C- CLASS OF SERVICE
CL- LIST COS
Description
Use this option to list the programmed Class of Service.
None
Default I 
 extensions  COS 
The attendant has COS 
See chart below for details.
Data Ports 
 Permanent Receive/Transmit Connection have COS 29.
Refer to the Data Products Manual.
The port pairs assigned to the STI have COS 31.
Feature
Automatic Call Distribution
Call Forwarding
Call Waiting
Callback
Centralized Attendant Service
Direct Inward Dialing
Direct Inward Dialing/Tie Lines
Direct Trunk...

C- CLASS OF SERVICE
CL- LIST COS
Instructions
To enter data on the PRF:
No entry required.
To enter data at the programming terminal:
Step 1 Press CL. The Class of Service listing displays. See below for a partial
COS CONFIGURATION l *** l **. 
BIT7 BIT6BIT5 BIT4BIT3BIT2
BYO:INH SYS SPEED DIALINH CALL FWDINH  ONBREAK-IN
OFF-i ICM  ONLY OPA BELL
CBACK PRIORITYPRIVACY EXTENDED RINGLOCAL CALL ATLOCAL ONLYTOLL RESTRICT 
BY2:SINGLE RG OPX NO  SLS  MONITORINH PG  2INH PG  INH  P C DIR
cos 
 0 0 : 00010000...

  2-2 PROGRAM RECORD FORM, CLASS OF SERVICE
      
 076
543210 765432-O
     
Tech Info Inc.
Call I-800-T.B. SOLVE
July 08, 1998
 PM
Tie  Nitsuko Digital Systems
Class of service: Class of service can be intimidating. This page is
taken from the DCW DCH Programming record form. This should
help. If you have any further questions please call (810) 39591 II, for
technical assistance. 

 CLASS OF SERVICE
CP- 
 SYSTEM SPEED DIAL 
Description
Related
Programming
l
l
Feature Reference
Instructions
Step  l
Step I 
Step  l
Issue 1-O
Use this option to  (0) or deny (1) extensions with this COS the ability to
use System Speed Dial. This option also restricts System Speed Dial for
 trunks and incoming tie trunks.
Condition.5
This option does not apply to CO trunks.
Default 
System Speed Dial enabled (0).
Speed Dial
E- Extensions. 
 Class of Service  Assign Class of Service to extensions.
E-...

C- CLASS OF SERVICE
CP- INHIBIT 
 FORWARDING 
Use this option to allow (0) or  (1) on-premise Call Forwarding-for
extensions with this COS. For system attendants (in COS 00). use 
to  the Alternate Attendant and Removing Trunks and Extensions
From Service features.
Conditions
None
Default Value
 Forwarding and Alternate Attendant enabled (0).
Related
Programming
l
Call Forwarding
CP- Allow Off-Premise Call Forwarding 
  For each COS, allow or
deny Off-Premise Call Forwarding.
E- Extensions, 
 Class of...

C- CLASS OF SERVICE
CP- INHIBIT CAMP-ON 
Description
Related
Programming
l
Feature Reference
Instructions
Step  
Step 1 
Step  
Issue 1-OUse this option to allow (0) or 
 (1) a user’s ability to send Call Waiting
(Camp-On) tones to a 
 extension  dialing 2. (To allow/deny a user’s
ability to Camp-On to a 
 trunk. refer to 
None
Default 
Camp-On to extensions allowed (0).
Call Waiting (Camp-On)
CP- Direct Trunk Access and Trunk Camp-On   An extension
user with Direct Trunk Access can camp-on to a busy...

C- CLASS OF SERVICE
CP- ALLOW BREAK-IN (INTRUSION) 
Description
Related
Programming
l
Feature Reference
Instructions
Step  l
Step 1 l
Step  
Use this option to enable (1) or disable (0) Intrusion for extensions  this
cos.
Conditions
None
Intrusion allowed ( 1) at COS 0.
Intrusion not 
 (0) at all other 
Intrusion
CP- Allow Privacy 
  Enable/disable Privacy for each Class of
Service. If an extension has Privacy. another extension cannot Intrude on its
calls.
E- Extensions. 
 Class of Service  Assign Class...

C- CLASS OF SERVICE
 ALLOW  CALL FORWARDING 
Description
Related
Programming
l
Feature Reference
Instructions
Step  
Step  l
Step  l
Use this option to allow (  or  (0) Off-Premise Call Forwarding for
extensions 
  COS.
Off-Premise Call  requires either ground start trunks or loop start
trunks 
 disconnect 
Default  
Off-Premise Call  not allowed (0).
Call Forwarding
CP- Inhibit Call Forwarding 
  For each COS, allow or deny Call
Forwarding.
E- Extensions. 
 Class of Service  Assign a COS to each...

C- CLASS OF 
CP- ALLOW ONLY    NIGHT 
Description
Related
Programming
l
l
l
Use this option to restrict estensions with this COS to only Intercom calls at
night. If enabled in an estension’s COS. the user can only place Intercom
calls when the 
 is in the night mode. The user cannot place  outside
calls (including 
   calls). When enabled  this option overrides AP- Toll
Restriction  programming. This option also pertains to incoming tie trunk
callers.
None
Default 
Estensions not restricted to Intercom...