TiE Onyx 2, 3, 4, 5 Service And Programming Manual

INTRODUCTION
The  
The Main Menu     basic programming options.
ACCESS ACCESS
CMD DESCRIPTION
LEVEL DESCRIPTIONLEVELATOLL RESTRICTION LIST  PROGRAM  INITIALIZE CCLASS OF SERVICE TABLE LIST  PROGRAM DISPLAY 0
EEXTENSION SETUP STATIONS1 LINES2FMISC.SYSTEM DATA EPROM CHECKSUMS 0 LCR   PARAMETER RESET GA  EDITOR2GL LCR TESTING 2SYSTEM STATUS REPORTS[A-I] 0ISYSTEM UTILITIES PORT RELEASE  SIDE TONE TEST  RESET LINE CARD 
KEY DATA LIST DATA   1LLIST SYSTEM DATA   DATA CANCEL ACCESS LEVEL0
NEXTENSION...

INTRODUCTION
The Sub-Menus
Certain Main Menu options  sub-menus. When vou type a letter for a
Main Menu option. 
 see a prompt   that the option has a
sub-menu. If you press RETURN. 
 see the sub-menu. The sub-menu
shows additional options. For esample. when you type 
S, you see: 
If you press RETURN. you see the Speed Dial sub-menu:
 SPEED D IAL
L- LIST MODE
P- PROGRAM 
R- ROTARY CONVERSION
The following Main Menu items have sub-menus:A- TOLL RESTRICTION
C- CLASS OF SERVICE
E- EXTENSION SETUP
RESETSGA-...

INTRODUCTION ,
Programming
Class of 
When programming Class of Service (CP). you usually enter a  for each
bit of each byte. 
 do.  have some additional options. If you
press RETURN after programming a byte. the system accepts vour entry and
skips to the next COS number. Or. 
 can press ESC in the  of a 
to cancel  entries. To  a COS unchanged. press RETURN before
typing 
 data.
Programming a
 Installed
When programming a new system. you may find the following helpful:
Verifv 
 trunk circuit  All...

A- TOLL RESTRICTION
  TOLL RESTRICTION
Description
Initialization erases all  Toll Restriction programming.
Related
Programming
l
l
l
l
Use the AI option  initialize Toll Restriction. Initialization loads 
standard (default) Toll Restriction programming.   
 Toll  for tire  
None
 
Toll Restriction not initialized.
Toll Restriction
 Toll   Enter the Toll Level  want to program.
AP- Allow Active Dial Pad 
  continued dialing for this Toll
Level (see Special Services and OCC Compatibility).
  Special...

A- TOLL RESTRICTION
AI- INITIALIZE TOLL RESTRICTION
Feature Reference
Toll Restriction
Instructions
To 
enter data on the PRF:
 entries required.
To initialize the Toll 
 data:
Step 1 lType AI. You  INITIALIZE DATABASE?
Step 3 Type Y. You see: DONE!
Step   Enter another option from the Toll Restriction menu.
OR
 Press ESC to return to the  
2-8  CONFIGURATIONIssue 1-O 

 TOLL RESTRICTION
 LIST TOLL RESTRICTION
Description
Use the AL option to list (display) the programmed AP- Program 
Restriction options for each toll 
Default 
ACTIVE DIAL PAD -Yes
ALLOW SPECIAL ACCESS 
 DIALING -Yes
ALLOW 0+ DIALING -Yes
ALLOW DIRECT 
 DIALING -Yes
ALLOW EQUAL ACCESS -Yes
EQUAL ACCESS ALLOW TABLE
TABLE EMPTY
ALLOW 
 DIALING -Yes
 ALLOW TABLE
TABLE EMPTY
ALLOW NNX DIALING -Yes
NNX ALLOW TABLE
TABLE EMPTY
ALLOW NPA DIALING -Yes
NPA ALLOW TABLE
TABLE EMPTY
SIX DIGIT ANALYSIS -Yes
Related...

A- TOLL RESTRICTION
AP- ALLOW 
  PXD
Description
Related
Programming
l
l
l
l
Use this option to enable disable continued dialing for extensions. With
continued dialing. the telephone outputs a digit over a trunk each time the user
presses a dial pad 
The   turns off the dial pad. Without
continued dialing. the 
 turns off the extension’s dial pad six seconds
after the user dials their last digit.
Conditions
Toll level 0  has Continued Dialing.
Default 
Continued dialing enabled.
Special Services and OCC...

A- TOLL RESTRICTION
 ALLOW ACTIVE  
Related
Programming
l
l
CP- Allow  Local  Calls      Extensions with this
option enabled can only place Intercom calls or local outside calls. This
    (except AP- Allow Active Dial Pad).
CP- Estension Toll Restriction 
   Assign a toll restriction
level (O-7) to a Class of 
E- Extensions.  Class  of   Assign Class of Service to extensions.
E- Trunks. EJ- Toll Restriction 
 Enable/disable Toll Restriction for each
trunk. For example. 
 lines  not require Toll...

A- TOLL 
AP-    
For  
 4R F    Issue 1-O 

 TOLL RESTRICTION
   ACCESS  
Description
Related
ProgrammingUse this option to 
 an extension user from directly dialing  
and   calls.  is any digit 7 to  If restricted. the system terminates
the call on the third digit of an 
  I call and the fourth digit of a  1  call.
a. To restrict international (0   ) calls. refer to Allow Outside Operator (0+)
Dialing 
b.The system never restricts 9   and  11 calls.
Default 
Special Access Dialing allowed.
Toll Restriction
AI- Initialize Toll Restriction...