TiE Onyx 2, 3, 4, 5 Service And Programming Manual

TIE LINES
Feature Operation
Step I 
Step  
Step  l
To Flash a tie line:
 At a  press FTR.
OR
 At an ESL set. press and release 
To use a Speed Dial  in the distant system:
Place call 
  line.
Listen for:Dial 
Dial the Speed Dial bin number.       Extension Speed Dial bins are Xl-19
 
Listen for:  dialing out
if  Dial   a pause.   have to press  to continue dialing.
Issue 1-OFEATURESl-227 

TIME AND DATE SETTING
Description
Programming
l
Related Features
The system Time and Date appears on:
l Display Telephones
l Station Message Derail Recording reports
 System Reports.  and  
 Traffic Management Report
A display 
  Class of Service 00 and the system administrator can
change the 
 and Date. Although entered in  format, the system
time always displays in I?-hour format (AM/PM).
None
Default 
Required Programming
E- Extensions.  Class  of   Assign COS 00 to each display 
that should be able...

TIME AND DATE SETTING
Feature Operation
Issue 1-O
Step 1 
Step 2 
Step 3 l
Step 6 
Step  l
Step 2 
Step 3 
Step  
Step  
Step 6 
Step  
Step  l
To set the system time (if   has COS 
Lift handset.
Press INTERCOM.
Look for: On
Listen for:Dial tone
Press PG Listen for:Dial  stops
Dial 8.
 Enter the hour (00-23).
Use a ‘J-hour clock (i.e..   PM = 
 Enter the minutes (00-59).
 Enter the seconds (00-59).Listen for: Dial  tone
Hang up.Look for: goes out
To set the  date (if   has COS 00):
Lift handset.
Press...

TOLL RESTRICTION
Description
Toll Restriction limits the numbers an extension user may dial. 
 allowing
extensions to place 
 certain types of calls. the system administrator can
control long distance 
costs. The  applies Toll Restriction according to
an extension’s Class of Service Toll Restriction Level. For each Toll
Restriction Level. the administrator can enable or disable:
l Continuous dialing (see Special  and OCC Compatibility)
 Special access  1) dialing (such as  Directory Assistance)
 Outside...

TOLL RESTRICTION
Programming
l
l
l
Required   
  Digit   Enable disable six-digit analysis for this Toll Level.
Also. program a 
 anal!  table.
CP- 
   Calls at Sight   At night. extensions
 this option  can  place Intercom calls. This assignment
 AP programming.
CP- 
 Only Local Calls     At night. extensions with
this option enabled can place Intercom calls and local outside calls. This
assignment 
  programming (except AP- Allow Active Dial Pad).
CP- Allow Only Local Calls 
 or Sight)   Extensions...

TOLL RESTRICTION
Related Features
Automatic Route  Cost Routing
A system can   LCR and Toll Restriction. When a user dials 9 or 90 for
ARS LCR.  LCR  Toll Restriction.
 Trunk Access
The system 
 not apply Toll  to calls placed using Direct TrunkAccess.
Last Number If  don’t diai enough digits (as determined  your Toll Restriction). Last
Number  and   ill not retain the digits  dial.
Night AnswerAn extension in a tenant group can have night mode restriction (e.g.. CP- Allow
Only Intercom Calls at 
  is...

  REPORTING
Description
The Traffic 
  Report  the  administrator
 ith a record of   stem’s call   The  Report consists of call
 details for each installed  trunk. trunk group and 
hunting group.   administrator can use the  Report to analyze
the 
 traffic.  in turn. lets the administrator maximize the 
resources.
In the large systems. the 
 report only outputs from the upper (local) COM
PCB port. In VS. the 
 report outputs from the main CEU AUX Module
serial port. 
 must  an  Module to have  reports....

TRAFFIC  REPORTING
Description
Traffic  Report For Trunks
IINCOMING CALLS CALLS CALLSLINE  NO. RCVD  ANSRD  LONG WAIT     ABANDONED  OUTGOING TINE
IN USE
801 0 0 00
080200
000
2
The TMS report for trunks 
 Trunk number
 For incoming calls. total calls received. answered and terminated
 is the total of all incoming calls detected at each trunk.
 is the total of all incoming calls actually answered by system
users for each trunk.
Terminated is the total calls terminated (completed) by system users for
each...

TRAFFIC  REPORTING
Programming
l
Related Features
Feature Operation
HE-  Status Reports. Traffic    Print the
TMS Report. The 
 does not clear the TMS data after the report runs.
HF- System Status Reports. Traffic 
 Summary  Data
Cleared) 
 Print the  Report. The system clears the  data after the
report runs.
QT- System Timers. Traffic 
 Report Wait Time  Set the
TMS Wait Time interval. If a call rings longer than this interval. the TMS
report flags it as Long Wait.
QZ- 
 Setup.  Report Print   Set the...

TRAFFIC  REPORTING  IV)
Description
The Traffic Management Report in ONYX IV only records trunk related
activity. The TMS report does not log Intercom calls or feature activation.
The report 
 includes extensions and trunks that had trunk call activity.
Refer to the Traffic Management Reporting feature on page l-233 for more
information on programming and running 
There are five parts to the Traffic  Report (shown below):
 Trunk calls at each extension
 Calls at each trunk
  group trunk calls for each...