TiE Onyx 2, 3, 4, 5 Service And Programming Manual

D- DISPLAY MEMORY
Description
Related
Programming
Feature Reference
Instructions
Issue 1-O
This program displays the contents of system memory locations. It is a
factory diagnostic tool. not intended for field use. Consult your Field Service
representative for more information.
Conditions
None
Default Value
None
None
System Reports, Diagnostics and Maintenance Utilities
None
 CONFIGURATION2-73 

D- DISPLAY MEMORY
 For Your Notes 
2-74 SOFTWARE   1-O 

E- EXTENSIONS
EO- ALL DATA
Description
Use EO to enter data for all options sequentially for an extension. The charts
below show the E options that correspond to each EO entry. Refer 
 these
options for more information. Also, the charts below show the default value
 each option (where applicable).
EO Prompts for 
For this option...Look here...
EXT
PORT
CIRCUIT COS (30 for Attendant, 01 for NEXT EXT IN 
HUNT TYPE DATA SET OR DATA MODULE? N [Y/N] PAGE ZONE RING-LINE PREFERENCE? N [Y/N] 
OFF-HOOK RINGING?...

E- EXTENSIONS
 ALL DATA
Description
(Cont’d)
EO Prompts for ESL Sets
For this option...
EXT
PORT
CIRCUIT TYPE cos 00 NEXT EXT  
HUNT TYPE PAGE ZONE ALLOW LINE DIAL-UP Y [Y/N] 
ACCESS TO GROUP 907 Y [Y/N] throughACCESS TO GROUP  Y [Y/N] DIR TERM OR OPR EXT RING DOWN (ONYX IV)
UCD MASTER EXT SPD DIAL BLOCKCALL PICKUP GROUP 
ACCESS CONTROLCOPY?  [Y/N] LINES 8 YYYY YYYY 
thtough65 TO 72 Y Y Y Y YYYY CALL-OUT CONTROLCOPY?  [Y/N] 
LINES 8 YYYY YYYY through
65 TO72 Y Y Y Y Y Y YY RING GROUP  PAGING THRU SPKR Y...

E- EXTENSIONS
EO- ALL DATA
Description
(Cont’d)
EO Prompts for  Sets
For this option...
EXT
PORT
CIRCUIT TYPE
 CIRCUIT # (OPX ports only)
cos 00 NEXT EXT IN HUNTHUNT TYPE 
ALLOW LINE DIAL-UP Y [Y/N] ACCESS TO GROUP  Y [Y/N] throughACCESS TO GROUP  Y [Y/N] DIR  OR OPR EXT 
RING DOWN (ONYX IV)UCD MASTER EXT SPD DIAL BLOCKCALL PICKUP GROUP ACCESS CONTROL
COPY? 
 [Y/N] LINES 1 TO8 YYYY YYYY through
65 TO 72
YYYY YYYY CALL-OUT CONTROLCOPY?  [Y/N] LINES 8 YYYY
YYYY 65 TO 72YYYYYYYY RING GROUP # VX N [Y/N]...

E- EXTENSIONS
EO- ALL DATA
EO Prompts for Data Sets, Data Ports and Data Modules
For this option...
Look here...
EXT
PORT
El
CIRCUIT TYPE (Ol-Data Module,  Set,  
DATA MODULE  PORT [NJ Y-(Data Port Only)E2cos 01 E3NEXT EXT IN HUNTE4HUNT TYPE 
DATA SET OR DATA MODULE? [Y/N]
(Y=Data Set and Data Module, N=Data Port)
PAGE ZONE E7RING-LINE PREFERENCE7 N [Y/N] E8OFF-HOOK RINGING? N [Y/N] E8KEY ACCESS TO OUTBOUND LINES Y [Y/N] E8ALLOW LINE DIAL-UP Y [Y/N] E8ACCESS TO GROUP  Y [Y/N] E8
through
ACCESS TO GROUP...

E- EXTENSIONS
EO- ALL DATA
Description
(Cont’d)
EO Prompts for Data Sets, Data Ports and Data 
 (Cont’d)
For this option...
(Data Module and Data Port only)
DATA MODULE BAUD RATES
0 DATA MODULE PARITY OPTIONSO-NO PARITY 8 BITS,l-EVEN 7  7 BITS
0 
INTERACTIVE MODE? N 
RS232 CONTROLS ACTIVE? N ALLOW DTR DISCONNECT? N ALLOW BREAK DISCONNECT? N 
AUTO BAUD? N BUSY ON DTR LOW? N 
Look here...
EM
EM
EM
EM
EM
EM
EM
EM
EO Prompts for Modem Pooling Circuits
For this option...Look here...
EXT
PORTEl
CIRCUIT TYPE...

E- EXTENSIONS
EO- ALL 
Related
Programming
Feature Reference
Instructions
step 1 
Step 1 
Step 2 l
Step 3 
Refer to the charts above.
Refer to the individual 
 options.
To enter data on the PRF:
Refer to the individual  options.
To enter data at the programming terminal:
Type 
Press RETURN to program extension 
OR
Enter another extension number and press RETURN. In either case, you see:
PORT
Enter data for the E options from Table 4.After you enter data for one option, you automatically advance to the...

E- EXTENSIONS
El- PORT 
Description
Use this option to change the port assignment for an extension. The port is
the hardware location of the extension. When you change an extension’s port
number, all programming for the extension goes to the new port assignment
(location).
All extensions use a single port, except for Data Sets, DSS Consoles and 
These are dual-port  that use a port pair. A port pair consists of two
consecutive ports, beginning with an even numbered port (e.g., 00 and 01).
When changing a...

E- EXTENSIONS
 CIRCUIT TYPE
Description
Use this option to identify. the type of telephone connected to each extension
port. The extension circuit type choices are:
00 ESL set
01 
 (lo-button or 30-button without display) and Data Module
(refer to the Data Products Manual)
02 30-button display 
03 Data Set (dual channel only  refer to the Data Products Manual)
04 Dual channel 
 (e.g., attendant phone P/N 88254)
05 OPX extension, AS1 without DTMF receiver (P/N 89748) and 
ports
06 DSS Console and ONYX IV...