Sharp Ux B700 Large Capacity Business Inkjet Fax Machine Operation Manual

							9
1. Installation
1.  Installation
Unpacking Checklist
If any are missing, 
contact your 
dealer or retailer.Before setting up, 
make sure you 
have all of the 
following items.
Operation 
manual Handset Handset 
cordTelephone 
line cordRapid Key 
labelsPrint 
cartridge Paper tray Paper tray 
coverDocument trayDocument 
exit support

(
3
3õ
)
6
6
2
¦
¦

(
.
,
¦

¦
¦

,
+
5
,
:
+
(
@ó
¦

,
*
,
4
)
,
9
¦øøó
¦ù÷÷ù
¦
¦øø

ùü
¦

 
						

							Attachments
10
Attachments
Points to keep in mind when setting up
Do not place the 
machine in direct 
sunlight.Do not place the 
machine near heaters 
or air conditioners.Keep dust away from 
the machine.
About condensation
If the machine is moved from a cold to a warm place, it is possible that 
condensation may form on the scanning glass, preventing proper scanning of 
documents for transmission. To remove the condensation, turn on the power and 
wait approximately two hours before using the machine.
Removing the packing tape
1Open the print compartment cover.
•Press as shown and pull the cover 
toward you.
2Remove the tape.

(
3
3õ
)
6
6
2
¦
¦

(
.
,
¦ø÷
¦
¦

,
+
5
,
:
+
(
@ó
¦

,
*
,
4
)
,
9
¦øøó
¦ù÷÷ù
¦
¦øø

ùü
¦

 
						

							Attachments
11
1. Installation
Connecting the handset
Connect the handset as shown and place it on the handset rest.
♦The ends of the handset cord are identical, so they will go into either jack.
Make sure the handset 
cord goes into the jack 
marked with a handset 
symbol on the side of 
the machine!
Use the handset to make ordinary phone calls, 
or to transmit and receive faxes manually.
3Close the printer cover.

(
3
3õ
)
6
6
2
¦
¦

(
.
,
¦øø
¦
¦

,
+
5
,
:
+
(
@ó
¦

,
*
,
4
)
,
9
¦øøó
¦ù÷÷ù
¦
¦øø

ùü
¦

 
						

							Attachments
12
Attaching the paper trays
Attach the paper tray.
Pull the paper plate 
toward you and attach 
the paper tray cover.
Paper plate
1
2
Attach the document 
tray.

(
3
3õ
)
6
6
2
¦
¦

(
.
,
¦øù
¦
¦

,
+
5
,
:
+
(
@ó
¦

,
*
,
4
)
,
9
¦øøó
¦ù÷÷ù
¦
¦øø

ùü
¦

 
						

							Attachments
13
1. Installation
Attach the document exit support.
Pull out the received 
document tray.

(
3
3õ
)
6
6
2
¦
¦

(
.
,
¦øú
¦
¦

,
+
5
,
:
+
(
@ó
¦

,
*
,
4
)
,
9
¦øøó
¦ù÷÷ù
¦
¦øø

ùü
¦

 
						

							Loading Printing Paper
14
1Pull the paper plate toward you, and 
remove the paper tray cover from the 
paper tray.
2If you are going to load legal paper, flip 
up the paper tray extension.
3Pull the paper plate toward you and insert the stack of paper into the 
tray, PRINT SIDE UP.
•If paper remains in the tray, take it out and combine it into a single stack 
with the new paper.
Loading Printing Paper
You can load letter or legal size paper in the paper tray. Recommended paper 
weight is 20-lb. Copy Bond. The maximum number of sheets is as follows:
Letter size: 
Approx. 200 sheets (20-Ib. copier paper at room temperature; 
maximum stack height should not exceed line on tray)
Legal size:  Approx. 100 sheets (20-Ib. copier paper at room temperature)
The stack 
should not 
be higher 
than this line
Be sure to load the paper so that 
printing takes place on the print side 
of the paper. Printing on the reverse 
side may result in poor print quality.

(
3
3õ
)
6
6
2
¦
¦

(
.
,
¦øû
¦
¦

,
+
5
,
:
+
(
@ó
¦

,
*
,
4
)
,
9
¦øøó
¦ù÷÷ù
¦
¦øø

ùü
¦

 
						

							Loading Printing Paper
15
1. Installation4Pull the paper plate toward you and 
replace the paper tray cover.
LEGALLETTER
Place the 
cover using the 
appropriate 
notch for the 
size of paper 
loaded

(
3
3õ
)
6
6
2
¦
¦

(
.
,
¦øü
¦
¦

,
+
5
,
:
+
(
@ó
¦

,
*
,
4
)
,
9
¦øøó
¦ù÷÷ù
¦
¦øø

ùü
¦

 
						

							Connecting the Power Cord
16
Connecting the Power Cord
Plug the power cord into a 120 V, 60 Hz, grounded AC (3-prong) outlet.
Caution!
♦Do not plug the power cord into any other kind of outlet. This will damage 
the machine and is not covered under the warranty.
♦Make sure you have removed all of the packing tape before plugging 
in the power cord (see page 10). Plugging in the power cord without 
doing so may damage the machine.
Note: If your area experiences a high incidence of lightning or power surges, 
we recommend that you install surge protectors for the power and telephone 
lines. Surge protectors can be purchased at most telephone specialty stores.
“CHECK CARTRIDGE” normally 
appears in the display the first 
time you plug in the machine. 
This message appears until you 
install the print cartridge.
The machine does not have 
a power on/off switch, so 
the power is turned on and 
off by simply plugging in or 
unplugging the power cord.

(
3
3õ
)
6
6
2
¦
¦

(
.
,
¦øý
¦
¦

,
+
5
,
:
+
(
@ó
¦

,
*
,
4
)
,
9
¦øøó
¦ù÷÷ù
¦
¦øø

ùü
¦

 
						

							Installing the Print Cartridge
17
1. Installation Installing the Print Cartridge
Caution!
Do not open the print compartment cover of the machine while it is 
printing. If opened while printing, printing will stop.
Note: Keep ink car tridges sealed in their packages until you are ready to install 
them.  It is recommended that you do not use a cartridge that has been left unused 
for a long time after opening, as the print quality may be considerably degraded.
♦Make sure the power cord of the machine is plugged in and paper is loaded 
before installing or replacing the print cartridge.
1Open the operation panel.
The initial starter print 
cartridge included with 
your fax can print about 
300 letter-size pages. When replacing the print 
cartridge, use a SHARP 
UX-C70B cartridge. One 
cartridge can print about 
600 letter-size pages.
If PRINTER ERROR or PRINTER ERROR/CHECK PAPER appears...
In the event that the display shows either of the above messages, you must clear the 
error before installing the print cartridge. The error can usually be cleared by opening 
and closing the print compartment cover (see Step 2), or if a paper jam has occurred, by 
removing the paper jam (see page 107).
The above 
yields are at 4% 
coverage in INK 
SAVE mode.

(
3
3õ
)
6
6
2
¦
¦

(
.
,
¦øþ
¦
¦

,
+
5
,
:
+
(
@ó
¦

,
*
,
4
)
,
9
¦øøó
¦ù÷÷ù
¦
¦øø

ùü
¦

 
						

							Installing the Print Cartridge
18
2Open the print compartment cover.
•Press as shown and pull the cover 
toward you.
3Remove only the tape from the the new 
cartridge.
•Important: Make sure you remove all 
of the tape.
•CAUTION! DO NOT touch the gold 
contact area of the cartridge.
4Make sure the cartridge holder is 
between the “CARTRIDGE EXCHANGE 
AREA” arrows on the label, and then 
pull the green lever and open the 
cartridge holder cover.
•If you are replacing the cartridge, 
remove the old cartridge. If you are 
going to use the old cartridge again, 
place it in an air-tight container.
•CAUTION! DO NOT touch the contact 
area inside the carriage carrier.
Note: If the print compartment cover is left 
open for approximately 30 minutes with a 
cartridge installed, the cartridge will 
automatically return to its home position. To 
make the cartridge return to the CARTRIDGE 
EXCHANGE AREA when this has happened, 
close the cover and then open it again.

(
3
3õ
)
6
6
2
¦
¦

(
.
,
¦øÿ
¦
¦

,
+
5
,
:
+
(
@ó
¦

,
*
,
4
)
,
9
¦øøó
¦ù÷÷ù
¦
¦øø

ùü
¦