Sharp Mx2310u User Guide

7-73
SYSTEM SETTINGS
Contents
Colour Adjustments
The following colour settings can be configured.
Initial Colour Balance Setting
Colour balance values obtained using Colour Balance 
in the special modes can be stored in a program (1 to 
48), and those values can be retrieved and stored as the 
initial colour balance setting*. Use this feature when you 
want to repeatedly use a colour balance setting for a 
favourite colour or for correction when a change occurs 
in the colour balance.
* Preset values...

7-74
SYSTEM SETTINGS
Contents
Network Settings
Network settings are described below. Touch the [Network Settings] key to configure the settings.
IPv4 Settings
When using the machine on a TCP/IP (IPv4) network, use 
this setting to configure the IP address of the machine.
The settings are shown below.
IP Address
Enter the IP address of the machine.
IP Subnet Mask
Entry the IP Subnet Mask.
IP Gateway
Enter the IP Gateway address.
DHCP
Use this setting to have the IP address obtained 
automatically using...

7-75
SYSTEM SETTINGS
Contents
Printer Settings
Settings related to the printer function can be configured. Touch the [Printer Settings] key to configure the settings.
Default Settings
Printer condition settings are described below.
Prohibit Notice Page Printing
This setting is used to disable printing of notice pages.
Prohibit Test Page Printing
This setting is used to disable printing of test pages. 
When this setting is enabled, Printer Test Page in the 
system settings cannot be used to print test...

7-76
SYSTEM SETTINGS
Contents
Interface Settings
These settings are used to control and monitor data transmitted to the USB port or network port of the machine.
Hexadecimal Dump Mode
(When the hard disk drive and  printer expansion kit 
are installed.)
This function is used to print the print data from a 
computer in hexadecimal format together with the 
corresponding ASCII text. This allows you to check 
whether or not print data from the computer is being 
transmitted to the machine correctly.
Example...

7-77
SYSTEM SETTINGS
Contents
Auto Colour Calibration
This is used to perform automatic colour correction when the colour in colour printing is off. The machine prints a test 
patch, the test patch is scanned, and the colour is automatically corrected.
After the [Execute] key is touched and a test patch is printed, a message appears prompting you to begin automatic 
calibration. Place the test patch on the document glass as shown below (so that the thin line at the edge of the page is to 
the left).
Lay...

7-78
SYSTEM SETTINGS
Contents
Image Send Settings
Settings related to the image send function (scan, Internet fax, etc.) can be configured. Touch the [Image Send Settings] 
key to configure the settings.
Operation Settings
The operation settings below apply to all image send functions.
Default Display Settings
You can select one of 5 base screen types for the base screen 
that appears when the [IMAGE SEND] key is touched or when 
the [CLEAR ALL] ( ) key is pressed in image send mode.
 Address Book
...

7-79
SYSTEM SETTINGS
Contents
Must Input Next Address Key at 
Broadcast Setting
This setting is used to require that the [Next Address] 
key be touched before the next address is entered when 
performing a broadcast transmission.
When this setting is enabled, the [Next Address] key 
cannot be omitted even if the next address is entered 
with a one-touch key.
If a user attempts to enter the next address without 
touching the [Next Address] key, a double-beep alarm 
will sound and the entry will be...

7-80
SYSTEM SETTINGS
Contents
Disable Registration of Program
This prohibits the use of the address book when a 
program is stored.
Configure the setting for each of the following items:
E-mail
 FTP
Desktop
 Network Folder
 Internet Fax (Including Direct SMTP)
Fax
Select All: Select all items.
Clear Checked: Clear all selections.
Disable Registration of Memory 
Box
Disable all types of memory box registration.
Configure the setting for each of the following items:
Polling Memory, Confidential,...

7-81
SYSTEM SETTINGS
Contents
Use this setting to enter the Internet fax address, fax 
number of the machine and the name of the user.
Sender Data Registration
Use this to store the sender name for fax and Internet 
fax, the sender number for fax, and the sender address 
for Internet fax.
The stored sender name and fax sender number or 
Internet sender address will be printed at the top of the 
received fax.
Sender Name
Enter the sender name. A maximum of 20 characters 
can be entered for the sender...

7-82
SYSTEM SETTINGS
Contents
Scan Settings
Settings related to scanning can be configured.
Default Sender Set
The information stored here is used if you do not specify 
[Reply-To] in the send settings when performing Scan to 
E-mail.
Sender Name
Enter a default sender name (maximum of 20 
characters).
Reply E-mail Address
Enter a default reply address (maximum of 64 
characters).
Default Colour Mode Settings
Select a default colour mode setting for both colour and 
black & white in scan mode.
Black &...