Sharp Mx 3501 N Manual

35
SPECIFYING THE ORIGINAL SIZE
When the original size is a non-standard size or is not detected correctly, manually specify the original size.
1
Touch the [Job Detail Settings] key.
2
Touch the [Original] key.
3
Specify the original size.
●Specifying an inch original size
(1) Touch the appropriate original size key.
(2) Touch the [OK] key.
●Specifying an AB original size
(1) Touch the [AB Inch] key.
(2) Touch the appropriate original size key.
(3) Touch the [OK] key.
Ready to scan for copy.
2-Sided...

36
STORING FREQUENTLY USED ORIGINAL SIZES
You can save special original sizes that you frequently use. This section explains how to store, call up, change, and 
delete special original sizes.
Storing original sizes
Up to 9 special original sizes can be stored.
●Specifying a non-standard original size
(1) Touch the [Size Input] tab.
(2)
Enter the X (horizontal) dimension of the original.
With the [X] key highlighted, enter the X (horizontal) 
dimension of the original with the     keys. When 
the document...

37
2
Touch the [Original] key.
3
Touch the [Custom Size] key.
4
Select a key for storing a custom 
original size.
(1) Touch the [Store/Delete] tab.
(2) Touch a key for storing a custom original 
size.
Touch a key that does not show a size ( ).
5
Enter the original size.
(1) Enter the X (horizontal) dimension of the 
original.
With the [X] key highlighted, enter the X (horizontal) 
dimension of the original with the     keys. A 
dimension from 2-1/2 to 17 (64 mm to 432 mm) can be 
entered.
(2) Enter the Y...

38
Using a stored original size
1
Touch the [Job Detail Settings] key.
2
Touch the [Original] key.
3
Touch the [Custom Size] key.
4
Call up the stored original size.
(1) Touch the [Recall] tab.
(2) Touch the key of the original size that you 
wish to call up.
(3) Touch the [OK] key.
To cancel the operation...
Press the [CLEAR ALL] key ( ).
Ready to scan for copy.
2-Sided CopyOriginal
0
Output
Special Modes
File
Quick File
Full ColorColor Mode
AutoExposure
100%Copy Ratio
 8 x111 
/
 2
2.3.4.
1.8 x11R8...

39
Changing a stored original size
1
Touch the [Job Detail Settings] key.
2
Touch the [Original] key.
3
Touch the [Custom Size] key.
4
Select the original size key that you wish 
to change.
(1) Touch the [Store/Delete] tab.
(2) Touch the original size key that you wish to 
change.
Touch the key ( ) that shows the original size 
that you wish to change.
5
Touch the [Modify] key.
Ready to scan for copy.
2-Sided CopyOriginal
0
Output
Special Modes
File
Quick File
Full ColorColor Mode
AutoExposure
100%Copy...

40
6
Change the original size.
(1) Enter the X (horizontal) dimension of the 
original.
With the [X] key highlighted, enter the X (horizontal) 
dimension of the original with the     keys. A 
dimension from 2-1/2 to 17 (64 mm to 432 mm) can be 
entered.
(2) Enter the Y (vertical) dimension of the 
original.
Touch the [Y] key and enter the Y (vertical) dimension of 
the original with the     keys. A dimension from 
2-1/2 to 11-5/8 (64 mm to 297 mm) can be entered.
(3) Touch the [OK] key.
7
Touch the [OK]...

41
Deleting a stored original size
1
Touch the [Job Detail Settings] key.
2
Touch the [Original] key.
3
Touch the [Custom Size] key.
4
Select the original size key that you wish 
to delete.
(1) Touch the [Store/Delete] tab.
(2) Touch the original size key that you wish to 
delete.
Touch the key ( ) that shows the original size 
that you wish to delete.
5
Touch the [Delete] key.
6
Touch the [OK] key.
To cancel the operation...
Press the [CLEAR ALL] key ( ).
Ready to scan for copy.
2-Sided CopyOriginal
0...

42
OUTPUT
To select output functions and the output tray, touch the [Output] key in the base screen of copy mode. Output functions 
that can be selected are sort, group, offset, staple sort, saddle stitch, and punch. All settings are explained in this section 
based on the assumption that a saddle stitch finisher, punch module and right tray are installed.
(1) [Group] key
This is used to group copies by page.
☞Group mode (page 43)
(2) [Staple Sort] key
This is used to sort the output into sets, staple...

43
OUTPUT MODES
This section explains the output functions.
Sort mode
This is used to sort (collate) output into sets.
Example: Sorting the originals into 5 sets
Group mode
This function groups copies by page.
Example: Groups of 5 copies of each page
Offset function
This function offsets each set of copies from the previous set in the output tray, making it easy to separate sets of copies.
The sort function is automatically selected when 
originals are placed in the automatic document feeder.
When the...

44
Staple sort function / Saddle stitch function
The staple sort function sorts output into sets, staples each set, and delivers the sets to the tray. The saddle stitch 
function staples each set in 2 places at the centerline and folds the stapled set.
The relations between the stapling positions, paper orientation, permitted paper sizes for stapling, and number of sheets 
that can be stapled are shown below.
For original placement orientations, see Original placement orientation (for the staple sort and...