Sharp Ar-m 351 Manual

2-23
2 TROUBLESHOOTING
Check the following troubleshooting list before requesting service as many problems can be fixed by the user. If you
are unable to solve the problem by checking the list, turn off the power switch, unplug the power cord.
Problems related to general use of the machine are described below. For problems related to the copy function, see
page 6-3. For problems related to document filing, see page 7-28. For fax, printer, and network scanner problems,
see the manuals for those functions....

TROUBLESHOOTING
2-24
Printing stops
before the job is
finishedIf too many pages collect on the output
tray, the tray full sensor activates and
stops printing.Remove the paper from the output tray.
You have run out of paper. Load paper. (Page 2-2)
Smudges on printed
sheetsDoes a message appear indicating the
need for maintenance?Please contact the your dealer as soon as
possible.
The displayed
paper size or paper
type does not match
the loaded paper
size or paper type.The correct paper size or paper type...

TROUBLESHOOTING
2-25
2
Printed paper is
wrinkled or the
image rubs off
easily.Is paper other than SHARP-
recommended paper being used?Use SHARP-recommended paper. (Page 2-16
)
Is paper size or weight out of the
allowable range?Use paper in the allowable range.
Paper damp?
Be sure to store paper in the wrapper in a dry
location and do not store paper in a location that is
humid
at a high temperature or an extremely low
temperature
exposed to direct sunlight
dusty.
The contrast on the
touch panel is...

Copy_EX.book  26 ページ  ２００４年９月２８日　火曜日　午後９時５４分 

3-1
CHAPTER 3
PERIPHERAL DEVICES
This chapter describes operating instructions for the Mail-Bin Stacker,
the Finisher, the Saddle Stitch Finisher, and the Duplex Module.
Page
DUPLEX MODULE ................................................................................. 3-2
Part names ...................................................................................... 3-2
Specifications .................................................................................. 3-2
Loading paper in the bypass...

3-2
DUPLEX MODULE
If a duplex module is installed, printing onto both sides of paper can be performed.
Two types of duplex modules are available: duplex module/bypass tray and duplex module. The descriptions in this
manual are for the duplex module/bypass tray. For information on misfeed removal for these modules, see page
2-19.
Part names
Specifications
*1For paper size and paper weight for the bypass tray, see Specifications of paper trays (types and sizes of
applicable papers for trays) on page 2-3....

DUPLEX MODULE
3-3
3
Loading paper in the bypass tray
The bypass tray can be used for plain paper and special paper including labels. Up to 100 sheets of standard paper
can be set. For paper types that can be used in the bypass tray, refer to page 2-3.
1Open the bypass tray.
When setting A3, B4,
11x 17, 8-1/2 x 14 or
8-1/2 x 13 paper, be
sure to extend the
bypass tray extension.
If the bypass tray
extension is not pulled
all the way out the size of
the loaded paper will not
be correctly displayed.
2Set...

DUPLEX MODULE
3-4
Troubleshooting (concerning the duplex module)
Check the list below before calling for service.
Problem Check Solution or cause
The machine will not
print duplex prints.Message indicating the paper type
cannot be used for two-sided printing
displayed?Special paper cannot be used for two-sided
printing. Use a paper type adequate for
two-sided printing. (See pages 2-4 and 3-2.)
Message indicating the paper size
cannot be used for two-sided printing
displayed?Use a paper size adequate for...

3-5
3 MAIL-BIN STACKER
The mail-bin stacker has 7 mail bins which can each be designated to receive printed output from a user or a group
of users .
Output paper in the copy mode and the fax mode will be delivered to the top tray of the stacker separated from printed
output. (Printed output can also be delivered to the top tray.)
Part names
Specifications
Specifications are subject to change for improvement without notice.
NOTES

Do not put pressure on the mail-bin stacker, particularly on the top tray...

MAIL-BIN STACKER
3-6
Misfeed in the mail-bin stacker
If a misfeed has occurred in the mail-bin stacker during printing, remove the misfed paper following the procedure
below.
1Open the top cover.
Move the tab in the
direction of the arrow as
shown in the illustration
to open the top cover.
2Remove the misfed paper.
Be careful not to tear the
misfed paper during
removal.
After removing the
paper, press down on
the top cover to close it.
3If the misfed paper is not found in step 2,
open the front cover....