Sharp Ar-m 351 Manual

PART 1: GENERAL INFORMATION
•BEFORE USING 
THE PRODUCT
•
MANAGING THE MACHINE
•PERIPHERAL DEVICES
PART 2: COPIER OPERATION
•MAKING COPIES
•CONVENIENT COPY 
FUNCTIONS
•
MACHINE MAINTENANCE 
(FOR COPYING)  
•DOCUMENT FILING 
FUNCTION
•
SPECIFICATIONS  1-1
2-1
3-1
4-1
5-1
6-1
7-1
8-1
Page
OPERATION MANUAL
(for general information and copier operation)
MODEL
AR-M351N
AR-M451N
LASER PRINTER
NAKS1CZZ
Be sure to become thoroughly familiar with this manual to 
gain the maximum benefit from the product. Before...

Warranty
While every effort has been made to make this document as accurate and helpful as possible, SHARP Corporation makes
no warranty of any kind with regard to its content. All information included herein is subject to change without notice. SHARP
is not responsible for any loss or damages, direct or indirect, arising from or related to the use of this operation manual. 
© Copyright SHARP Corporation 2004. All rights reserved. Reproduction, adaptation or translation without prior
written permission...

Part 1: General Information
Copy_EX.book  1 ページ  ２００４年９月２８日　火曜日　午後９時５４分 

Copy_EX.book  2 ページ  ２００４年９月２８日　火曜日　午後９時５４分 

0-1
PRODUCT CONFIGURATIONS
The table below shows the product models covered by this manual. 
(As of October 2004)
OPERATION MANUALS
The following operation manuals are provided for the machine. Please read the appropriate manuals as needed for
the features you wish to learn about.
Operation manual (for general information and copier operation) (this manual):
The first half of this manual provides general information about the machine, including safety information, loading
paper, removing misfeeds, and...

0-2
Improper installation may damage this product. Please note the following during initial installation and whenever the
machine is moved.
1.The machine should be installed near an
accessible power outlet for easy connection.
2.Be sure to connect the power cord only to a
power outlet that meets the specified voltage and
current requirements. Also make certain the
outlet is properly grounded.
For the power supply requirements, see the
name plate on the back of the main unit.
3.Do not install your...

0-3
CAUTIONS
1.Do not touch the photoconductive drum. Scratches or smudges on the
drum will cause dirty prints.
2.The fusing unit is extremely hot.  Exercise care in this area. 
3.Do not look directly at the light source. Doing so may damage your
eyes.
4.Five adjusters are provided on all optional stand/paper drawer units.
These adjusters should be lowered until they contact the floor. 
When moving the machine with the optional stand/paper drawer, be
sure to raise the adjusters. Also, unlock the two...

CAUTIONS
0-4
Laser Information
Wave length
785 nm+10 nm
-15 nm
Pulse times North America: 35 cpm model: (4.1 µs ± 4.1 ns)/7 mm
45 cpm model: (5.7 µs ± 5.7 ns)/7 mm
Europe:  35 cpm model: (3.8 µs ± 3.8 ns)/7 mm
45 cpm model: (4.4 µs ± 4.4 ns)/7 mm
Output power 0.2 mW - 0.4 mW
At the production line, the output power of the scanner unit is adjusted to 0.4 MILLIWATT PLUS 8 % and is maintained
constant by the operation of the Automatic Power Control (APC).
Caution
Use of controls or adjustments or...

0-5
CONTENTS
Page
PRODUCT CONFIGURATIONS .................................. 0-1
OPERATION MANUALS.............................................. 0-1
INSTALLATION REQUIREMENTS.............................. 0-2
CAUTIONS................................................................... 0-3
Laser Information ................................................. 0-4
CONTENTS ................................................................. 0-5
CHAPTER 1
BEFORE USING THE PRODUCT...

CONTENTS
0-6
CHAPTER 5
CONVENIENT COPY FUNCTIONS
SPECIAL MODES ........................................................ 5-2
General procedure for using special functions ..... 5-2
Margin shift ........................................................... 5-3
Erase .................................................................... 5-4
Dual page copy..................................................... 5-5
Pamphlet copy ...................................................... 5-6
Job build...