Sharp Ar-m 351 Manual

5-1
CHAPTER 5
CONVENIENT COPY 
FUNCTIONS
This chapter explains special-purpose functions, storing of copy
settings, and other convenient functions. Please select and read
sections of this chapter as needed.
Page
SPECIAL MODES ................................................................................... 5-2
General procedure for using special functions ................................ 5-2
Margin shift...................................................................................... 5-3
Erase...

5-2
SPECIAL MODES
Touch the [SPECIAL MODES] key in the main screen of copy mode to open the special modes screen. The following
functions can be selected in the special modes screen.
(1) Margin shift (page 5-3)
(2) Erase (page 5-4)
(3) Dual page copy (page 5-5)
(4) Pamphlet copy (page 5-6)
(5) Job build (page 5-8)
(6) Tandem copy (page 5-9)(7) [OK] key on the special modes screen
Touch the [OK] key to return to the main screen of
copy mode.
(8) /  key
Touch these keys to change the special modes
screen....

SPECIAL MODES
5-3
5
Margin shift
The margin shift function will automatically shift the text or image on the copy paper approximately 10 mm (1/2) in
its initial setting. 
This function is convenient when stapling or binding copies with a string.
1Touch the [MARGIN SHIFT] key on the
special modes screen.
The margin shift setting
screen will appear.
The margin shift icon
( ) will also appear in
the upper left of the
screen to indicate that
the function is turned on.
2Select the shift direction.
Touch a...

SPECIAL MODES
5-4
Erase
The erase function is used to erase the shadow lines on copies produced when copying thick originals or books. The
erase modes that can be selected are shown below. The erase width is approximately 10 mm (1/2) in its initial
setting.
EDGE ERASE
Eliminates shadow lines around the edges of
copies caused when heavy paper or a book is used
as an original.
CENTRE ERASE
Eliminates shadow lines produced by the bindings
of bound documents.
EDGE + CENTRE ERASE
Eliminates shadow lines...

SPECIAL MODES
5-5
5
Dual page copy
The dual page copy function produces separate copies of two documents placed side by side on the document glass.
This function is especially useful when copying books and other bound documents.
[Example] Copying right and left pages of a book
1Touch the [DUAL PAGE COPY] key on the
special modes screen.
The [DUAL PAGE
COPY] key will be
highlighted to indicate
that the function is
turned on, and the dual
page copy icon ( ) will
appear in the upper left
of the screen....

SPECIAL MODES
5-6
Pamphlet copy
The pamphlet copy function is used to arrange copies in proper order for eventual centre-stapling and folding into a
booklet. Two original pages are copied onto each side of copy paper. Four pages are, therefore, copied onto one sheet.
This function is convenient for arranging copies into an attractive booklet or pamphlet.
[Example] Copying eight originals in the pamphlet copy mode
When using this function, a duplex module must
be installed.
Scan the originals from the...

SPECIAL MODES
5-7
5
5Select whether or not you wish to copy on
the cover (YES or NO).
6Select the paper tray for the cover.
(1)The currently selected
paper tray for the
cover is displayed.
(2)The size and type of
paper in the currently
selected tray is
displayed.
In the example screen above, A4 (8-1/2 x 11)
size plain paper is loaded.
To change the paper tray for the cover, touch the tray
selection key. (In the screen example, the  TRAY2
display is the tray selection key.)
The tray selection screen...

SPECIAL MODES
5-8
Job build
Use job build mode when you need to copy more originals than can be placed in the document feeder at once. The
maximum number of originals that can be placed in the document feeder at once is 50 sheets (30 sheets when the
size is B4 or larger; for more information see Acceptable originals on page 4-2). This function lets you divide and
scan the originals in sets. This function allows the original pages to be scanned in sets.
[Example] Copying 100 pages of A4 originals
1Touch...

SPECIAL MODES
5-9
5
Tandem copy
Two machines connected to the same network can be used to run a large copy job in parallel.
By dividing the job in half, approximately half the time is required to complete the job.
To use this function, two machines must be connected to your network as network printers. Even if more machines are
connected to the network, this function can only be used to have one other machine share a job.
Server machine and client machine
In the following explanations, the machine on...

SPECIAL MODES
5-10
5Press the [START] key.
NOTES
To perform tandem copying, the server machine and client machine must meet certain conditions.
After the [START] key is pressed on the server machine, the server machine verifies that the conditions have
been met. If the conditions have not been met, tandem copying does not begin and TANDEM OUTPUT IS
NOT ALLOWED. OUTPUT ALL SETS USING MASTER MACHINE? appears in the display. To have the
server machine make all the copies, touch the [OK] key. To cancel the...