Sharp Ar-m 351 Manual

SADDLE STITCH FINISHER
3-17
3

 Saddle stitch function
The saddle stitch finisher can automatically place two
staples for centreline binding of prints or copies and fold
them along the centreline.

 Hole punching (only if a punch module is
installed)
If the saddle stitch finisher is equipped with a hole punch
module, printed paper can be hole punched and delivered
to the offset tray. Saddle stitching and hole punching
cannot be selected at the same time. The automatic image
rotation will not...

SADDLE STITCH FINISHER
3-18
Using the saddle stitch finisher
When [OUTPUT] is selected on the main screen of copy mode, a screen for making selections for sort, group, staple
sort, saddle stitch, punch and exit tray will appear.
(1) [GROUP] key (See page 3-15.)
When Group is selected, all copies of the same
original will be grouped.
(2) [STAPLE SORT] key (See page 3-16.)
When Staple Sort is selected, sorted sets will be
stapled and delivered to the offset tray. (They will
not be offset stacked.)
(3)...

SADDLE STITCH FINISHER
3-19
3
Staple cartridge replacement and staple jam removal
When the staple cartridge becomes empty or staples become jammed, a message will appear in the message
display of the operation panel.
Follow the procedure below to replace the staple cartridge or remove jammed staples.

 Staple cartridge replacement
1Open the front cover.
2Pull out the stapler section.
3Turn roller rotating knob A in the direction
of the arrow to move the staple unit to the
front.
Turn the roller...

SADDLE STITCH FINISHER
3-20

 Staple jam removal
1Unlatch the saddle stitch finisher and slide
it away from the machine.
2Open the front cover.
3Turn roller rotating knob C as shown in the
illustration until the blue indication is
seen.
4Remove the paper from the stapler
compiler.
5If saddle stitch was selected, open the
saddle stitch section cover.
6Remove the misfed paper.
Be careful not to tear the
misfed paper during
removal.
7Close the saddle stitch section cover.
8Open the front cover and pull...

SADDLE STITCH FINISHER
3-21
3
9Turn roller rotating knob A in the direction
of the arrow to move the staple unit to the
front.
Turn the roller rotating
knob until the triangle
mark is aligned with the
index.
10Remove the staple box.
11Raise the lever at the end of the staple box.
Remove the top staple if
it is bent. If bent staples
remain, a staple jam will
occur again.
12Return the lever to its original position.
13Reinstall the staple box.
Push the staple box in
until it clicks into place.
14Push the...

SADDLE STITCH FINISHER
3-22
Misfeed in the saddle stitch finisher
When a misfeed occurs in the saddle stitch finisher, remove the misfed paper following the procedure below.
1Press the detach button and separate the
saddle stitch finisher from the machine.
2Remove any misfed paper from the
machine.
3If there was no misfed paper in step 2, pull
roller rotating knob B on the punch unit
toward you and rotate it. (Only when an
optional punch unit is installed.)
Rotating roller rotating
knob B releases the...

SADDLE STITCH FINISHER
3-23
3
10Open the front cover.
11Rotate roller rotating knob D in the direction of
the arrow.
12Remove any misfed paper from the saddle
stitch tray.
Remove the paper
gently, taking care not to
tear it.
13Close the cover of the saddle stitch section.
14Close the front cover.
15Push the saddle stitch finisher back onto the
machine.
Roller rotating knob D
Copy_EX.book  23 ページ  ２００４年９月２８日　火曜日　午後９時５４分 

SADDLE STITCH FINISHER
3-24
Troubleshooting (concerning the saddle stitch finisher)
Check the list below before calling for service.
* When a punch module is installedProblem Check Solution or cause
The saddle stitch
finisher does not
operate.Are any saddle stitch finisher covers open? Close all covers. (See page 3-14.)
Message indicating need to remove paper
from the stapler compiler displayed?Remove all remaining paper from the stapler
compiler referring to step 4 on page 3-20.
Stapling cannot be...

Part 2: Copier Operation
Copy_EX.book  1 ページ  ２００４年９月２８日　火曜日　午後９時５４分 

Copy_EX.book  2 ページ  ２００４年９月２８日　火曜日　午後９時５４分