Sanyo Pdg Dwt50l Projector User Manual

2. Installation and Connections 
22
 
q Throw Distance and Screen Size 
Example of LNS-S40: 
The further your projector is from the screen or wall, the  larger the image. The minimum size the image can be is approxi-
mately 40 inches (1 m) measured diagonally  when the projector is roughly 71 inches (1.8 m) from the wall or screen. The 
largest the image can be is 500 inches (12.7 m) when the projector is about 915 inc hes (23.2 m) from the wall or screen. 
 
Screen Size LNS-W41 LNS-W40 LNS-S40 
0.77...

2. Installation and Connections 
23 
 
Screen Size LNS-T40 LNS-T41 
2.22 - 4.43 4.43 - 8.3 Diagonal Width Height Distance 
[inches] [m] [inches] [m] [inches] [m] [inches] [m] [inches] [m] 
40 1.02 34.3  0.87 20.5 0. 52 75.7 - 155.0 1.92 -3.94 151.7 -289.8 3.85 -7.36 
50  1.27 42.9  1.09 25.6 0. 65 95.7 - 194.7 2.43 -4.95 190.9 -363.5 4.85 -9.23 
60  1.52 51.6  1.31 30.7 0. 78 115.6 - 234.5 2.94 -5.96 230.2 -437.3 5.85 -11.11 
67  1.70 57.6  1.47 34.3 0.87  129.6 - 262.4 3.29 -6.66  257.7 - 488.9 6.55...

2. Installation and Connections 
24
 
r Installing the Optional Color Wheel 
The PDG-DWT50L projector comes with a four-segment color w heel installed. An additional six-segment color wheel is op-
tional. To replace the color wheel (located under the lamp  cover adjacent to lamp 1) refer to the following guide. 
Note: 
Wait until the lamp house and the color wheel cool off. 
1.  Loosen the captive screw (A) 
on the lamp cover. 
 
2.  Remove the lamp cover by 
sliding it in the direction of 
the arrow...

2. Installation and Connections 
25 
4.  Lift the color wheel in the di-
rection shown. 
 
5.  Insert the six-segment color 
wheel  
 
6.  Secure the retaining screws as 
shown. 
  

2. Installation and Connections 
26
7.  Align the lamp cover (A) with 
the arrow mark on the cabinet 
and slide it into place. 
 
8.  Secure the captive screw (B).  
 
Storing Unused Color Wheel:  
Keep the unused color wheel in the zipper bag in which the  6-segment color wheel (not supplied) was packaged.  
This bag prevents dust from falling or collecting on the color wheel. 
 
s  Making Connections 
Connecting Your PC or Macintosh Computer
 
Enabling the computer’s external display 
Displaying an...

2. Installation and Connections 
27 
 
2.  Turn on the projector and select the chosen method of  connection from the source menu before turning on the 
PC (see  o Selecting an Input Source on page  34). 
3.  Turn on the PC. 
Note: 
Failure to follow the above steps may not activate the digital output of the graphics card resulting in no \
pic-
ture being displayed. Should this happen, restart your PC.    

2. Installation and Connections 
28
 
Connecting an External Monitor 
Connect an external monitor to the projector through RGB out connections as shown below  
(see item 4,  r Terminal Panel Features on page  9) 
 
 
  

2. Installation and Connections 
29 
 
Connecting Your DVD Player with Component Output 
To connect a DVD Player to the projector, refer to the following guide. \
1.  Connect the DVD Player to the projector as shown  below before turning on the Player or the projector. 
 
2.  Turn on the projector and select  Component from the source menu before turning on the DVD Player  
(see  o Selecting an Input Source on page  34). 
3.  Turn on the DVD Player. 
Note: 
Refer to your DVD players users manual for...

2. Installation and Connections 
30
 
Connecting Your VCR or Laser Disc Player 
To connect your VCR or Laser Disc Player, refer to the following diagram. 
 
 
Note:  
Refer to your VCR or laser disc player user’s manual for more information about your device’s requirements.  
Images may not be displayed correctly when using an S-Video or Video connection \
to fast-forward or fast-
rewind scanning.  
 
The AUDIO IN RCA jack is shared  between VIDEO IN and S-VIDEO IN.  

2. Installation and Connections 
31 
 
t Connecting the Supplied Power Cable 
This projector uses nominal input voltages of 100–120V or 200–240V\
  AC and it automatically selects the correct input volt-
age. It is designed to work with single-phase power system s having a grounded neutral conductor. To reduce the risk of 
electrical shock, do not plug into any other type of power sy stem. If you are not sure of the type of power being supplied, 
consult your authorized dealer or service  station....