Sanyo Pdg Dwt50l Projector User Manual

1. Introduction 
12
 
Important: 
Avoid using the projector with bright fluorescent lighting turned on. Ce\
rtain high-frequency fluorescent lights 
can disrupt remote control operation. 
1. Be sure nothing obstructs the path between the remote control and the projector. If the path between re-
mote and projector is obstructed, you can bounce the remote signal off certain reflective surfaces such as 
projector screens. 
2. The buttons and keys on the projector have the same functions as the corresponding...

1. Introduction 
13 
 
Battery Installation 
The Remote Control unit included with the projector does not c ontain batteries, though batteries are supplied as part of the 
complete package. To insert (or replace)  the batteries, refer to the following guide. 
1.  Remove the battery compartment cover 
by squeezing the locking catch and slid-
ing the cover in the direction of the 
arrow. 
 
2.  Insert the supplied batteries taking note 
of the polarity (+/-) as shown. 
 
3.  Replace the cover locator, and...

1. Introduction 
14
 
Operating Range for Wireless Remote Control 
Point the remote control toward the projector (to Infrared Remote Re-
ceivers) when pressing the buttons. Maximum operating range for the 
remote control is about 16.4 feet (5 m) and 60 degrees in front and rear 
of the projector. 
Infrared remote receivers are provided both in front and back of the pro\
-
jector. You can conveniently  use both of the receivers. 
Remote Control Precautions 
The following precautions ensure that  the...

1. Introduction 
15 
Using the Remote Control in Wired Operation 
Connect the supplied remote cable to the R/C jack on the projector (see\
  r Terminal Panel Features on page  9) and the 
other end to the remote jack on the remote control (see item 1,  s Part Names of the Remote Control on page  11). 
Note:  
Connecting the remote cable to the R/C jack on the terminal panel will make the wireless operation unavail-
able. 
 
 
 
  

1. Introduction 
16
Carrying the Projector 
Always carry your projector by the handle. 
Before moving or carrying the projector, disconnect the power cable and any other cables that may be attached to it. 
When moving the projector or when the projector is not in use, cover the lens with the lens cap. 
To extend the projector handle, refer to the following guide. 
1.  Stand the projector on its end with  the control panels at the bottom. 
2.  Lift the handle in the direction  shown until it is fully...

 
17 
2. Installation and Connections 
n Setting Up the Screen and the Projector 
This section briefly describes how to set  up your projector and how to connect video and  
audio sources.  
Your projector is simple to set up and use.  But before you get started, you must first:  
•  Set up a screen and the projector.  
•  Connect your computer or video equipment to the projector. See  s Making Connections on page  26. 
•  Connect the supplied power cable. See  t Connecting the Supplied Power Cable on...

2. Installation and Connections 
18
 
o Selecting a Location 
Locating the projector correctly ensures  optimum performance and a longer parts life. 
Take note of the following when setting up the projector: 
• The projector table or stand should be level and sturdy. 
•  Position the projector so that it is perpendicular to the screen. 
•  Ensure cables do not cause a trip hazard. 
 
 
  

2. Installation and Connections 
19 
p Installing or Removing the Optional Lens 
CAUTION 
  • 
Do not shake or place excessive pressure on the projector or the lens components as the projector and 
lens components contain precision parts. 
•  When shipping the projector with the optional lens, re move the optional lens before shipping the projec-
tor. The lens and the lens shift mechanism ma y encounter damage caused by improper handling during 
transportation. 
•  Before removing or installing the lens,...

2. Installation and Connections 
20
3.  Pull out the existing lens slowly. 
 
 
CAUTION 
  When Installing the lens into the projector, be sure to remove the lens cap from the back of the optional 
lens before installing the optional lens into the projec
tor. Failure to do so will cause damage to the projec-
tor. 
 
Installing the New Lens 
1.  Insert the lens label side up. 
 
2.  Rotate the lens clockwise until it 
clicks into place. 
  

2. Installation and Connections 
21 
Installing the New Lens Using the anti-theft screw
 Using the anti-theft screw to prevent theft of 
the lens. 
Tighten the supplied anti-theft screw on the 
front bottom.