Sanyo Pdg Dwt50l Projector User Manual

5. Using On-Screen Display 
72
Keystone 
The keystone trapezoid can be adjusted by selecting this option. 
 
Select Horizontal or Vertical using  ▲or▼  then, use  ◄or►  to adjust the projected image appearance as required. 
Lamp control 
Select Normal or Eco from the lamp mode window. The lamp life can be extended by us ing the Eco mode and the fan 
noise can be reduced. 
 
 
Lamp mode 
Select the lamps to be used for projection. 
 
Select from the following: 
Dual  – Uses both lamps simultaneously....

5. Using On-Screen Display 
73 
 
Lamp interval 
The period of time for regulating lamp usage when not in dual lamp mode.\
 
 
Select from the following: 
Off , 1 week, 4 weeks  and 2000H   
 
Simple menu 
Select the Simple menu to display. 
 
 
Set Simple menu On or Off.  

5. Using On-Screen Display 
74
 
Language 
Select the OSD language to be used. 
 
Select from the following: 

5. Using On-Screen Display 
75 
 
Installation 
The Installation tab contains menu options for various setup  conditions such as orientation and remote sensor mode and is 
accessed through the Setup menu. 
 
The following table lists all functions with a brief description. 
ITEM DESCRIPTION 
Ceiling & Rear  Select from four projection met
hods depending on projection site  
(see Ceiling & Rear page  76). 
Communication speed  Select Communication speed.  
Range: 4800bps, 9600bps, 19200bps, 38400bps 
Menu...

5. Using On-Screen Display 
76
ITEM DESCRIPTION 
Key lock Set Control panel lock On/Off. Note: 
y This Control Panel Lock does not affect the remote control functions. 
y When the control panel is locked, pressing and holding the Cancel butto\
n 
on the projector cabinet for about 10 seconds. The setting will change t\
o Off.
 
DynamicBlack DynamicBlack
TM improves the black level of the projector. Black level is the darkest 
part of a picture and varies between  viewing devices and environments. 
Set...

5. Using On-Screen Display 
77 
 
Communication speed 
Select communication speed to set the baud rate of the connection.  
Note:  
Longer cable connections may require lower settings.  
 
Select from the following options: 

5. Using On-Screen Display 
78

5. Using On-Screen Display 
79 
 
PIN Code Lock 
See t Preventing the Unauthorized Use of the Projector on page  51 – 53. 
 
Key lock 
Turn On/Off the Key Lock function for cabinet buttons. 
Note: 
y This Control Panel Lock does not affect the remote control functions. 
y When the control panel is locked, pressing and holding the Cancel butto\
n on the projector cabinet for 
about 10 seconds. The setting will change to Off. 
 
 
 
DynamicBlack 
DynamicBlackTM enables you to improve the black level of the...

5. Using On-Screen Display 
80
 
Network Setting 
See Network setting on page 82. 
 
Standby mode 
There are two standby modes available: No rmal and Power-saving. Power-saving mode  allows you to put the projector in 
the standby condition to consume less power than Normal. 
 
 
Note: 
Be sure to connect the projector and computer while the projector is in standby mode and before turning on 
the computer. 
 
Select from the following: 

5. Using On-Screen Display 
81 
 
PC control 
This function enables you to select the path for PC control (see  r PC Control Codes and Cable Connections  
on page  115). 
 
 
Note: 
In the Network mode, Communication Speed function is not available.  
Select from the following: