Panasonic Matrix Switcher Wj Sx150 Operating Instructions

103
1. Press the RESET button while holding down the SHIFT
button.
2. The monitor, the LED display and the indicator will
change as follows:
ALARMnn will disappear from the monitor.
The LED display will return to the state before the
alarm input.
The alarm indicator will go out.
The CAM indicator will return to the state before the
alarm input.
■Suspending the Alarm Inputs
Use this function when you do not want to be disturbed by
an alarm input, for example, during the setup procedures.
1. Press the...

104
MULTIPLEXER OPERATIONS 
Multiplexer board WJ-SXB151 is an optional board.
It enables multiscreen display, electronic zooming, still pic-
ture and multiscreen sequence.
It also enables the operation of Digital Disk Recorder WJ-
HD100 Series or time-lapse VCR, when connected to them.
Note:Before the use, it is necessary to install the
Multiplexer board in the matrix switcher and config-
ure the system through SETUP MENU and WJ-
SX150 Administrator Console. [Refer to p. 34
Installing the Multiplexer...

105
●Electronic Zooming (EL-ZOOM)
Playback spot pictures can be electrically zoomed.
1. Select the desired monitor. (Refer to p. 90 Monitor
Selection and p. 91 Camera Selection.)
2. Press the RECORDER button. (Refer to p. 116 Recorder
Mode.) The system will enter the recorder mode.
3. Press the PLAY button. (Refer to p. 117 Normal
Playback.) The system will enter the playback mode.
4. Select a camera channel by pressing a numeric button
and then pressing the CAM (SET) button. The selected
camera image...

107
OPERATING PROCEDURES
(PS·DATA) 

108
WHEN USING A PS·DATA SYSTEM CONTROLLER
This manual describes the operating procedures which are specifically related to WJ-SX150.
For the basic operating procedures such as log-in/log-out, camera selection, and camera control, etc., refer to the system con-
trollers operating instructions.
The following are different from the terminal mode when you use the system controller via the PS·Data protocol.
•Camera selection, camera control, camera site accessories control are in accordance with the PS·Data...

109
Refer to the system controller’s operating instructions
before you login the system. After the log-in procedure, the
following operations are available to control the system.
The operation begins with selecting a monitor, then the
selected camera appears the active monitor.
■ Monitor Selection
Unit addresses are given to each monitor. 
Rotary SW Mon 1 Mon 2 Mon 3 Mon 411234
The following is how to select a monitor.
1. Press the numeric button(s) to select the desired moni-
tors unit address.
2. Press...

110
■ Tour Sequence
The following functions are available if a tour sequence has
been previously configured through SETUP MENU or WJ-
SX150 Administrator Console. Any tour sequence can be
assigned to any monitors.
1. Select the desired monitor. (Refer to p. 109 Monitor
Selection.)
2. To select the desired tour sequence number, press the
numeric buttons.
3. Press the SEQ button to run the tour sequence in the
forward direction on the active monitor.
4. Press the SEQ PAUSE button to pause a tour sequence...

111
The procedure described below lets you determine on-screen display (OSD) items, such as camera title, clock and status, on
and off on the active monitor screen.
Before controlling each item, monitor selection is necessary. (Refer to p. 109 Monitor Selection.)
1. Press the SHIFT button, and then press the numeric buttons corresponding to the function code. 
(Refer to the table.)
2. Press the FUNCTION button. The function will be executed.
Notes:
•Alarm History Table doesnt have a function code. When...

112
■Resetting All the Alarm Inputs
You can reset all the alarm input signals at a time. 
1. Select a monitor which displays ALARM.
(Refer to the figure on p. 102.)
2. Press the SHIFT button, and then press the ALL RESET
button.
All the alarms will be reset.
Then, the LED display and indicators will return to the
state before the alarm input.
Note:You cannot reset the alarm input signals one by one.
■Suspending All the Alarm Inputs
Use this function when you do not want to be disturbed by
an alarm input,...

113
This section will describe what you should take notice when
using a PS·Data system controller. The same descriptions
as the system controller’s operating instructions are not
mentioned here. Refer to them. 
■Controlling the Unit with a PS·Data
System Controller
1. Before operating the recorder, it is necessary to enter
the recorder mode. (Refer to p. 124 or p. 125.)
2. Enter the desired function code (refer to the diagram)
and press the FUNCTION button.
MULTIPLEXER OPERATIONS (PS · Data)