Panasonic Matrix Switcher Wj Sx150 Operating Instructions

93
■ Call Preset Position
1. Select the desired monitor and camera. (Refer to p. 90
Monitor Selection and p. 91 Camera Selection.)
2. To select the desired preset position number, press the
numeric buttons.
4. When you have selected a wrong number, press the
CLEAR button to clear the numeric input.
3. Press the CALL PRESET button to move to the preset
position of the selected camera on the active monitor.
■ Program Preset Position
1. Select the desired monitor and camera. (Refer to p. 90
Monitor...

94
■ Camera Function (Shortcut Function)
The following function is available only when specified cam-
eras with the camera function feature are used.
This function enables executing camera functions via a
shortcut.
1. Select the desired monitor and camera. (Refer to p. 90
Monitor Selection and p. 91 Camera Selection.)
2. Press the AUTO PAN button while holding down the
SHIFT button.
F_ _ _ _  will appear on the LED display of the con-
troller as shown in the figure.
■ Camera Setup
1. Select the desired...

95
■ Patrol Learn and Play
A routine of manual operations can be stored for a specific
time and later reproduced repetitively.
1. Select the desired monitor and camera. (Refer to p. 90
Monitor Selection and p. 91 Camera Selection.)
2. Press the AUTO PAN button three times while holding
down the SHIFT button.
LEARN will appear on the LED display of the controller
as shown in the figure.
■ Changing to Black and White Images
This function gets the clear camera images on the monitor
while shooting the...

96
■ Camera Panning Function
There are three panning modes available as follows: auto
pan, sort mode and sequence mode. Refer to p. 16
Camera-related Functions for details on each mode.
1. Select the desired monitor and camera. (Refer to p. 90
Monitor Selection and p. 91 Camera Selection.)
2. Press the AUTO PAN button four times while holding
down the SHIFT button.
PAN will appear on the LED display of the controller as
shown in the figure.4. To exit from the mode, press the MON (ESC) button,
then press...

97
■ Receiver Control
The following functions are available only when the
receivers are included in the system and the specified
camera housing is installed.
● Camera Housing Control
Wiper Control
1. Select the desired monitor and camera. (Refer to p. 90
Monitor Selection and p. 91 Camera Selection.)
2. Press the CAM (SET) button while holding down the
SHIFT button to turn on the housing wiper of the camera
until buttons are released.
Defroster Control
1. Select the desired monitor and camera. (Refer to...

98
■ Tour Sequence
The following functions are available if a tour sequence has
been previously configured through SETUP MENU or WJ-
SX150 Administrator Console. Any tour sequence can be
assigned to any monitors.
1. Select the desired monitor and camera. (Refer to p. 90
Monitor Selection and p. 91 Camera Selection.)
2. To select the desired tour sequence number, press the
numeric buttons.
3. When you have selected a wrong number, press the
CLEAR button to clear the numeric input.
4. Press the TOUR SEQ...

99
■ On-screen Display (OSD) Control
The procedure described below lets you determine the dis-
play parameters, such as camera title, clock and status, on
and off on the active monitor screen.
Before controlling each item, monitor selection is neces-
sary. (Refer to p. 90 Monitor Selection.)
●Displaying the Clock 
Toggle the button 1 while holding down the OSD button. 
(1) will appear/disappear on/from the active monitor.
●Displaying the Camera Title
Toggle the button 2 while holding down the OSD...

100
MODE:Lists the display mode on the moni-
tors.
SPOT:Spot mode
Tnn:Tour Sequence mode (nn is the tour 
sequence number.)
SET:WJ-SX150 Setup mode
ALARM:Alarm Active mode
ACK:Alarm ACK mode
VLD H:VLD History Table 
ALM H:Alarm History  Table
SYS S:System Status Table 
KB:Lists the system controller number or 
PC.
OPE:Lists the operator number
PRI:Lists the priority number
3. To exit from the mode, press the CLEAR button.●Moving the Event Display
Move the joystick while holding down the OSD, SHIFT and
3...

101
■ Alarm History Table
There are 100 alarm records stored in chronological order
in 10 pages of tables.
1. Select the desired monitor. (Refer to p. 90 Monitor
Selection.)
2. Press the button 7 while holding down the OSD button.
OSD will appear on the LED display, and the ALARM
HISTORY table will appear on the active monitor as
shown in the figure.
The columns in the table indicate the states as follows:
DATE:Lists the date and time when the alarm state
changes.
ALARM:Lists the alarm number (01 - 16)....

102
■Operating during an Alarm Mode
While an alarm mode is active, the following are available
from the system controller:
•Operating the camera with the alarm input (ACK)
•Resetting the alarm (RESET/ALL RESET)
•Suspending the alarm (ALM SUSPENDED)
■Operation of an Alarm-related
Camera (ACK)
You can operate the camera with the alarm input as follows:
1. Select a monitor which displays ALARM.
2. Press the ACK button.
ACK will appear on the monitor with an alarm input.
The camera with an alarm input will...