Panasonic Matrix Switcher Wj Sx150 Operating Instructions

53
●How to Display
To display this menu on the monitor, move the cursor to 100
TIME & DATE in SETUP MENU by moving the joystick to D
or C.
●Parameters
You can move the cursor to each parameter by moving the
joystick to Aor B.
• Month
Press the NEXT or PREV button to select the correct month.
• Day
Press the numeric buttons to enter it directly. 

54
 300 SEQUENCE
     
     TOUR NO. =1
 STEP CAM  PRE DWELL  STEP CAM  PRE DWELL
    1   1   --    2S     9   9   --    2S
    2   2   --    2S    10  10   --    2S
    3   3   --    2S    11  11   --    2S
    4   4   --    2S    12  12   --    2S
    5   5   --    2S    13  13   --    2S
    6   6   --    2S    14  14   --    2S
    7   7   --    2S    15  15   --    2S
    8   8   --    2S    16  16   --    2S
 400 ALARM
 410 ALARM MODE    SEQUENCE 
/ DWELL 2sec
 420  ALARM EVENTOALARM INPUT
 430...

55
• Year
Press the numeric button to enter the correct year.
• TIME
Press the numeric button to enter the correct time.
• MINUTE
Press the numeric button to enter the correct minute.
• AM/PM
Press the NEXT or PREV button to select the correct time.
After the configuration, press the SETUP button while hold-
ing down the SHIFT button. The configuration will be updat-
ed when closing SETUP MENU. 
Notes:
• Adjust the time and date when the clock display is differ-
ent from the current one.
• The clock...

56
TOUR NO:Press the NEXT or PREV button to select the
tour number. Or press the numeric button(s) to
enter a number.
STEP: This stands for a tour sequence step.
CAM: This stands for a camera number. CAM 0 to 16 is
selectable. CAM 0 deactivates the sequence step. 
The factory default setting is assigned to each step
in numerical order (STEP 1 = CAM 1, STEP 2 =
CAM 2, STEP 3 = CAM 3, STEP = 4, CAM 4, STEP 5
= CAM 5…)
PRE: This stands for a camera’s preset position num-
ber. 1 to 64 or - - is selectable....

57
OFF:An alarm input is not accepted via the ALARM
port.
The factory default setting is ON.
Each alarm inputs polarity is configurable in 440 ALARM
INPUT (ALARM PORT).
Set ALARM PORT to ON or REC ONLY, and press the CAM
(SET) button.
440 ALARM INPUT (ALARM PORT) will appear on the moni-
tor.
To select an alarm input polarity required for the ALARM
port, press the PREV or NEXT button.
N.O.:Selects Normally Open alarm contact.
N.C.:Selects Normally Closed alarm contact.
TIME:Enables the input for time...

58
• MUX MOTION DET
This menu appears only when the Multiplexer board is
installed in the unit.
This stands for that the unit’s motion detector is activat-
ed when a camera detects the brightness-level change
and transmit an alarm signal.
ON:The alarm-associated sequence/spot image is dis-
played on a monitor, and alarm recording will start
(if a recorder is connected to the unit.)
REC ONLY:Only alarm recording will start and moni-
tors will keep displaying the current sequence/spot
images.
Note:You...

59
■CAMERA TITLE
●How to Display
To display this menu on the monitor, move the cursor to 500
CAMERA TITLE in SETUP MENUby moving the joystick to
▼or ▲. Then, press the CAM (SET) button. The submenu
appears on the monitor.
●How to edit
A camera title is composed of up to 20 characters.
Each camera number is fixed and the subsequent 20 char-
acters are editable.
The characters available here are the following:
ABCDEFGHIJKLMNOPQRSTUVWXYZabcdefghijklmnopqrs
tuvwxyz0123456789!#$%&()*+,-./:;=?•_(space) 
The...

60
•When moving the joystick to ▲at the top of CAMERA
TITLE 2 of 2, the monitor will display 1 of 2 (the previous
page).
•Original characters  are configurable through WJ-
SX150 Administrator Console, but they are not dis-
played correctly in SETUP MENU. They are displayed
as ■. (Refer to p. 80 Edit Font window.)
■RECORDER
●How to Display
To display this menu on the monitor, move the cursor to 600
RECORDER in SETUP MENU by moving the joystick to D
or C. Then, press the CAM (SET) button. The submenu will...

61
• DATA4/PSD PORT SELECT
This stands for the operation mode: PS·Data or the terminal
mode.
PSD:Select this when connecting a PS·Data controller
to the DATA 4 port.
DATA 4: Select this when connecting a terminal-mode
controller to the DATA 4 port.
The factory default setting is PSD.
• PSD/HDR PORT SPEED
This stands for the PS·Data communication speed (or baud
rate) of the DATA 4 port.
19200, 9600 or 4800 bps is selectable.
The factory default setting is 9600 bps.
• SERIAL PORT SPEED
Select the desired...

62
• CAMERA CLEANING
ON:Activates the manual cleaning for the cameras.
OFF:Deactivates the manual cleaning.
When you set CAMERA CLEANING to ON and exit from the
SETUP MENU, camera cleaning will start.
The factory default setting is OFF.
Notes:
•When the camera cleaning is active, cleaning will begin
from CAM 1 in numerical order. 
•Surveillance is impossible during the cleaning. 
•The cleaning cannot be stopped after it is started.
•Refer to pp. 38 and 39 for details on RS-485 or PS·Data
connections....