Panasonic Matrix Switcher Wj Sx150 Operating Instructions

							93
■ Call Preset Position
1. Select the desired monitor and camera. (Refer to p. 90
Monitor Selection and p. 91 Camera Selection.)
2. To select the desired preset position number, press the
numeric buttons.
4. When you have selected a wrong number, press the
CLEAR button to clear the numeric input.
3. Press the CALL PRESET button to move to the preset
position of the selected camera on the active monitor.
■ Program Preset Position
1. Select the desired monitor and camera. (Refer to p. 90
Monitor Selection and p. 91 Camera Selection.)
2. To move the camera to the position to be preset, move
the joystick and press the lens control buttons.
3. To select the desired preset position number, press the
numeric buttons.
4. When you have selected a wrong number, press the
CLEAR button to clear the numeric input.
4. Press the CALL PRESET button while holding down the
SHIFT button to save a preset position of the selected
camera.
SHIFT
CALL
PRESET
PROGRAM
PRESET
PAUSE
TOUR SEQ
NEXT
AUTO PAN
PAUSE
CAM FUNC
CLEAR
LOG OUTMON LOCK
DEF ON
WIPER
DEF OFFMON (ESC)
T&D CAM ID
MON STATUSALLEVENT
ALM H VLD H SYS S
CAM (SET)
MULTI SCREEN SEL
SEQUENCE
AUX2 ON AUX2 OFFEL-ZOOM
AUX1 ON AUX1 OFFSTILL
Notes:
•If the entered position number has stored the previ-
ous preset position, it will be overwritten by the new
one.
•SETUP MENU and WJ-SX150 Administrator
Console can configure each operators pan/tilt con-
trol. (Refer to p. 62 OPERATOR REGISTRATION or
p. 75 Operator Registration.)Note:To use the above function, you must set the pre-
set position number for the camera.
CALL
PRESET
PROGRAM
PRESET
AUTO PAN
CAM FUNC
CLEAR
LOG OUTMON LOCK
DEF ON
WIPER
DEF OFFMON (ESC)
T&D CAM ID
MON STATUSALLEVENT
ALM H VLD H SYS S
CAM (SET)
MULTI SCREEN SEL
SEQUENCE
AUX2 ON AUX2 OFFEL-ZOOM
AUX1 ON AUX1 OFFSTILL 
						

							94
■ Camera Function (Shortcut Function)
The following function is available only when specified cam-
eras with the camera function feature are used.
This function enables executing camera functions via a
shortcut.
1. Select the desired monitor and camera. (Refer to p. 90
Monitor Selection and p. 91 Camera Selection.)
2. Press the AUTO PAN button while holding down the
SHIFT button.
F_ _ _ _  will appear on the LED display of the con-
troller as shown in the figure.
■ Camera Setup
1. Select the desired monitor and camera. (Refer to p. 90
Monitor Selection and p. 91 Camera Selection.)
2. Press the F1 button while holding down the SHIFT but-
ton.
The CAM SETUP indicator on the controller will light up
and the cameras SETUP MENU will appear on the
active monitor.
3. To select the desired item in the menu, move the joy-
stick to ▼or ▲. To select the desired parameter (or
mode) in the menu, move the joystick to tor s.
4. To execute the currently highlighted selection and to
enter a submenu of SETUP MENU, press the CAM
(SET) button.
5. To leave from the currently selected menu and to return
to the previous page of the menu, press the MON (ESC)
button.
6. Move the cursor to SPECIAL on the camera’s setup
menu, and press numeric buttons 4and 6simultane-
ously for 2 seconds or more to display the special
menu.
7. Move the cursor to CAMERA RESET on the camera’s
setup menu, and press buttons 4, 5and 6simultane-
ously to reset all the functions to the defaults.
Notes:
•Refer to the operating instructions of the selected
camera for details.
•Move the joystick while holding down the SHIFT
button to move  the camera smoothly for presetting
the positions in the cameras SETUP MENU.
8. To close the cameras SETUP MENU, press the F1 but-
ton while holding down the SHIFT button.
The CAM SETUP indicator goes off.
CAMERA FUNCTION CONTROL
SETUP
SHIFT
REW/FF
STEP
CALL
PRESET
PROGRAM
PRESET
GROUP SEQ
PAUSE
SUSPEND
F1
CAM SETUPALL RESET
ACKRESET
F2
TOUR SEQ
PREVNEXT
STOP
OSD
AUTO PANRECORDER
INDEX
STOP PLAYPAUSE
CAM FUNC
CLEAR
LOG OUTMON LOCK
DEF ON
WIPER
DEF OFFMON (ESC)
T&D CAM ID
MON STATUSALLEVENT
ALM H VLD H SYS S
CAM (SET)
MULTI SCREEN SEL
SEQUENCE
AUX2 ON AUX2 OFFEL-ZOOM
AUX1 ON AUX1 OFFSTILL
3. Press the numeric buttons to select an assigned func-
tion number, then press the CAM (SET) button.
For example, enter 175 for AGC ON.
The selected function will be executed on the active
monitor.
Notes:
•When you select a wrong number, press the CLEAR
button to clear the numeric input.
•Refer to the cameras operating instructions for
details on available shortcuts.
4. To exit from the mode, press the MON (ESC) button
then press the AUTO PAN button while pressing the
SHIFT button.
SETUP
SHIFT
REW/FF
STEP
CALL
PRESET
PROGRAM
PRESET
GROUP SEQ
PAUSE
SUSPEND
F1
CAM SETUPALL RESET
ACKRESET
F2
TOUR SEQ
PREVNEXT
STOP
OSD
AUTO PANRECORDER
INDEX
STOP PLAYPAUSE
CAM FUNC
CLEAR
LOG OUTMON LOCK
DEF ON
WIPER
DEF OFFMON (ESC)
T&D CAM ID
MON STATUSALLEVENT
ALM H VLD H SYS S
CAM (SET)
MULTI SCREEN SEL
SEQUENCE
AUX2 ON AUX2 OFFEL-ZOOM
AUX1 ON AUX1 OFFSTILL 
						

							95
■ Patrol Learn and Play
A routine of manual operations can be stored for a specific
time and later reproduced repetitively.
1. Select the desired monitor and camera. (Refer to p. 90
Monitor Selection and p. 91 Camera Selection.)
2. Press the AUTO PAN button three times while holding
down the SHIFT button.
LEARN will appear on the LED display of the controller
as shown in the figure.
■ Changing to Black and White Images
This function gets the clear camera images on the monitor
while shooting the objects under low light conditions.
1. Select the desired monitor and camera. (Refer to p. 90
Monitor Selection and p. 91 Camera Selection.)
2. Press the AUTO PAN button two times while holding
down the SHIFT button.
BLACK (black) will appear on the LED display of the
controller as shown in the figure.
3. Press the button 1 to change the image from the color
mode to the black and white mode on the active moni-
tor.
BL ON (BLACK ON) appears on the LED display to
indicate the selected mode.
4. Press the button 2 to change the black and white image
to the color image on the active monitor.
BL OF (BLACK OFF) appears on the LED display to
indicate the selected mode.
5. Press the MON (ESC) button to exit from the mode.
Note:When the black and white parameter is set to
AUTO in the cameras SETUP MENU, this function
is disabled.
SETUP
SHIFT
REW/FF
STEP
CALL
PRESET
PROGRAM
PRESET
GROUP SEQ
PAUSE
SUSPEND
F1
CAM SETUPALL RESET
ACKRESET
F2
TOUR SEQ
PREVNEXT
STOP
OSD
AUTO PANRECORDER
INDEX
STOP PLAYPAUSE
CAM FUNC
CLEAR
LOG OUTMON LOCK
DEF ON
WIPER
DEF OFFMON (ESC)
T&D CAM ID
MON STATUSALLEVENT
ALM H VLD H SYS S
CAM (SET)
MULTI SCREEN SEL
SEQUENCE
AUX2 ON AUX2 OFFEL-ZOOM
AUX1 ON AUX1 OFFSTILL
SETUP
SHIFT
REW/FF
STEP
CALL
PRESET
PROGRAM
PRESET
GROUP SEQ
PAUSE
SUSPEND
F1
CAM SETUPALL RESET
ACKRESET
F2
TOUR SEQ
PREVNEXT
STOP
OSD
AUTO PANRECORDER
INDEX
STOP PLAYPAUSE
CAM FUNC
CLEAR
LOG OUTMON LOCK
DEF ON
WIPER
DEF OFFMON (ESC)
T&D CAM ID
MON STATUSALLEVENT
ALM H VLD H SYS S
CAM (SET)
MULTI SCREEN SEL
SEQUENCE
AUX2 ON AUX2 OFFEL-ZOOM
AUX1 ON AUX1 OFFSTILL
3. To save the patrol sequence, follow the procedure
below.
qPress the button 2, then press the CAM (SET)  but-
ton.
LE R appears on the LED display.
wOperate the camera manually. 
ePress the button 3.
The operation data is saved and LE S appears on
the LED display.
4. To reproduce the operation data, follow the procedure
below.
qPress the button 1.
LE P appears on the LED display.
wPress the button 3.
The reproduction is ended.
5. To exit from the mode, press the MON (ESC) button. 
						

							96
■ Camera Panning Function
There are three panning modes available as follows: auto
pan, sort mode and sequence mode. Refer to p. 16
Camera-related Functions for details on each mode.
1. Select the desired monitor and camera. (Refer to p. 90
Monitor Selection and p. 91 Camera Selection.)
2. Press the AUTO PAN button four times while holding
down the SHIFT button.
PAN will appear on the LED display of the controller as
shown in the figure.4. To exit from the mode, press the MON (ESC) button,
then press the AUTO PAN button while holding down
the SHIFT button.
SETUP
SHIFT
REW/FF
STEP
CALL
PRESET
PROGRAM
PRESET
GROUP SEQ
PAUSE
SUSPEND
F1
CAM SETUPALL RESET
ACKRESET
F2
TOUR SEQ
PREVNEXT
STOP
OSD
AUTO PANRECORDER
INDEX
STOP PLAYPAUSE
CAM FUNC
CLEAR
LOG OUTMON LOCK
DEF ON
WIPER
DEF OFFMON (ESC)
T&D CAM ID
MON STATUSALLEVENT
ALM H VLD H SYS S
CAM (SET)
MULTI SCREEN SEL
SEQUENCE
AUX2 ON AUX2 OFFEL-ZOOM
AUX1 ON AUX1 OFFSTILL
3. Press the assigned numeric button shown below to acti-
vate the panning function of the selected camera.
The LED display indicates the selected mode as fol-
lows.
1:Activates AUTO PAN PA PA.
2:Activates SORT PAN PA SO.
3:Activates SEQUENCE PAN PA SE.
Note:The AUTO MODE parameter previously set in the
cameras SETUP MENU will be automatically
replaced to the activated function parameter. 
						

							97
■ Receiver Control
The following functions are available only when the
receivers are included in the system and the specified
camera housing is installed.
● Camera Housing Control
Wiper Control
1. Select the desired monitor and camera. (Refer to p. 90
Monitor Selection and p. 91 Camera Selection.)
2. Press the CAM (SET) button while holding down the
SHIFT button to turn on the housing wiper of the camera
until buttons are released.
Defroster Control
1. Select the desired monitor and camera. (Refer to p. 90
Monitor Selection and p. 91 Camera Selection.)
2. Press the button 9 while holding down the SHIFT button
to turn on the housing defroster of the camera.
3. To turn off the defroster, press the button 8 while hold-
ing down the SHIFT button.
● Auxiliary Control
1. Select the desired monitor and camera. (Refer to p. 90
Monitor Selection and p. 91 Camera Selection.)
2. Press the button 3 while holding down the SHIFT button
to turn on the users auxiliary switch 1 of the receiver.
Press  the button 2 while holding down the SHIFT but-
ton to turn off the users auxiliary switch 1 of the receiv-
er.
3. Press the button 6 while holding down the SHIFT button
to turn on the users auxiliary switch 2 of the receiver.
Press the button 5 while holding down the SHIFT button
to turn off the users auxiliary switch 2 of the receiver.
SHIFT
PAUSE
TOUR SEQ
NEXT
PAUSE
MON LOCK
DEF ON
WIPER
DEF OFFMON (ESC)
T&D CAM ID
MON STATUSALLEVENT
ALM H VLD H SYS S
CAM (SET)
MULTI SCREEN SEL
SEQUENCE
AUX2 ON AUX2 OFFEL-ZOOM
AUX1 ON AUX1 OFFSTILL
SHIFT
PAUSE
TOUR SEQ
NEXT
PAUSE
MON LOCK
DEF ON
WIPER
DEF OFFMON (ESC)
T&D CAM ID
MON STATUSALLEVENT
ALM H VLD H SYS S
CAM (SET)
MULTI SCREEN SEL
SEQUENCE
AUX2 ON AUX2 OFFEL-ZOOM
AUX1 ON AUX1 OFFSTILL
SHIFT
PAUSE
TOUR SEQ
NEXT
PAUSE
MON LOCK
DEF ON
WIPER
DEF OFFMON (ESC)
T&D CAM ID
MON STATUSALLEVENT
ALM H VLD H SYS S
CAM (SET)
MULTI SCREEN SEL
SEQUENCE
AUX2 ON AUX2 OFFEL-ZOOM
AUX1 ON AUX1 OFFSTILL
CAMERA SITE ACCESSORIES CONTROL 
						

							98
■ Tour Sequence
The following functions are available if a tour sequence has
been previously configured through SETUP MENU or WJ-
SX150 Administrator Console. Any tour sequence can be
assigned to any monitors.
1. Select the desired monitor and camera. (Refer to p. 90
Monitor Selection and p. 91 Camera Selection.)
2. To select the desired tour sequence number, press the
numeric buttons.
3. When you have selected a wrong number, press the
CLEAR button to clear the numeric input.
4. Press the TOUR SEQ button to run the tour sequence in
the forward direction on the active monitor.8. Press the PREV button to move the sequence one
frame to the previous step from the step that was previ-
ously paused by pressing the PAUSE button.
9. Press the STOP button to stop a tour sequence on the
active monitor and return to spot monitoring.
■ Group Sequence
The following function is available only if a group sequence
has been previously established in WJ-SX150 Administrator
Console.
As described earlier, a group sequence determines the
assignment of monitors and cameras. Therefore, monitor
selection is not required.
1. Press the numeric buttons to select a desired group
sequence number.
2. When you have selected a wrong number, press the
CLEAR button to clear the numeric input.
3. Press the GROUP SEQ button to run a group sequence
forward on the assigned monitors.
4. Press the PAUSE, NEXT or PREV button to operate the
group sequence. Refer to steps 5 to 8 of Tour
Sequence in this page for how to use these buttons. 
5. To stop the sequence, select one of the monitors that
are being run on the selected group sequence, then
press the STOP button.
RUNNING SEQUENCE
SETUP
SHIFT
REW/FF
STEP
CALL
PRESET
PROGRAM
PRESET
GROUP SEQ
PAUSE
SUSPEND
F1
CAM SETUPALL RESET
ACKRESET
F2
TOUR SEQ
PREVNEXT
STOP
OSD
AUTO PANRECORDER
INDEX
STOP PLAYPAUSE
CAM FUNC
CLEAR
LOG OUTMON LOCK
DEF ON
WIPER
DEF OFFMON (ESC)
T&D CAM ID
MON STATUSALLEVENT
ALM H VLD H SYS S
CAM (SET)
MULTI SCREEN SEL
SEQUENCE
AUX2 ON AUX2 OFFEL-ZOOM
AUX1 ON AUX1 OFFSTILL
5. Press the PAUSE button to pause a tour sequence on
the active monitor.
The P sign (indicating the pause status) is displayed
at the tour sequence number on the active monitor, and
a camera number currently selected appears on the
LED display.
6. Press the PAUSE button to restart a tour sequence for-
ward from the next step that was previously paused by
pressing the PAUSE button.
7. Press the NEXT button to move the sequence one
frame to the next step from the step that was previously
paused by pressing the PAUSE button.
SETUP
SHIFT
REW/FF
STEP
CALL
PRESET
PROGRAM
PRESET
GROUP SEQ
PAUSE
SUSPEND
F1
CAM SETUPALL RESET
ACKRESET
F2
TOUR SEQ
PREVNEXT
STOP
OSD
AUTO PANRECORDER
INDEX
STOP PLAYPAUSE
CAM FUNC
CLEAR
LOG OUTMON LOCK
DEF ON
WIPER
DEF OFFMON (ESC)
T&D CAM ID
MON STATUSALLEVENT
ALM H VLD H SYS S
CAM (SET)
MULTI SCREEN SEL
SEQUENCE
AUX2 ON AUX2 OFFEL-ZOOM
AUX1 ON AUX1 OFFSTILL 
						

							99
■ On-screen Display (OSD) Control
The procedure described below lets you determine the dis-
play parameters, such as camera title, clock and status, on
and off on the active monitor screen.
Before controlling each item, monitor selection is neces-
sary. (Refer to p. 90 Monitor Selection.)
●Displaying the Clock 
Toggle the button 1 while holding down the OSD button. 
(1) will appear/disappear on/from the active monitor.
●Displaying the Camera Title
Toggle the button 2 while holding down the OSD button.
(2) will appear/disappear on/from the active monitor.
●Displaying the Event
Toggle the button 3 while holding down the OSD button. 
(3) will appear/disappear on/from the active monitor.
●Displaying the Monitor Status*
Toggle the button 4 while holding down the OSD button. 
(4)* will appear/disappear on/from the active monitor.
* Monitor number, controller number and monitor mode
●Displaying All the Items
Toggle the button 5 while holding down the OSD button.
(1), (2), (3) and (4) will appear/disappear on/from the active
monitor.
■ On-screen Display (OSD) Position
Control
The procedure described below lets you determine the dis-
play positions, such as camera title, clock and status, on
the active monitor screen.
●Moving the Clock Display 
Move the joystick while holding down the OSD, SHIFT and
1 buttons. (1) will move to the desired direction.
●Moving the Camera Title Display
Move the joystick while holding down the OSD, SHIFT and
2 buttons. (2) will move to the desired direction.
MONITOR DISPLAY CONTROL
08/21/2002 12:50:28 PM
M1  K1 T01
C01 camera title          ALARM10*(1)
(3) (4)
(2)
SET UP
SHIFT
REW/FF
STEP
GROUP SEQ
PAUSE F2
TOUR SEQ
PREVNEXT
STOP
OSD
RECORDER
INDEX
STOP PLAYPAUSE
MON LOCK
DEF ON
WIPER
DEF OFFMON (ESC)
T&D CAM ID
MON STATUSALLEVENT
ALM H VLD H SYS S
CAM (SET)
MULTI SCREEN SEL
SEQUENCE
AUX2 ON AUX2 OFFEL-ZOOM
AUX1 ON AUX1 OFFSTILL
08/21/2002 12:50:59 PM
M1  K1 T01
C01 camera title          ALARM10*
Camera title
Monitor statusEvent
Clock
SET UP
SHIFT
REW/FF
STEP
GROUP SEQ
PAUSE F2
TOUR SEQ
PREVNEXT
STOP
OSD
RECORDER
INDEX
STOP PLAYPAUSE
MON LOCK
DEF ON
WIPER
DEF OFFMON (ESC)
T&D CAM ID
MON STATUSALLEVENT
ALM H VLD H SYS S
CAM (SET)
MULTI SCREEN SEL
SEQUENCE
AUX2 ON AUX2 OFFEL-ZOOM
AUX1 ON AUX1 OFFSTILL
UP
LR
DOWN 
						

							100
MODE:Lists the display mode on the moni-
tors.
SPOT:Spot mode
Tnn:Tour Sequence mode (nn is the tour 
sequence number.)
SET:WJ-SX150 Setup mode
ALARM:Alarm Active mode
ACK:Alarm ACK mode
VLD H:VLD History Table 
ALM H:Alarm History  Table
SYS S:System Status Table 
KB:Lists the system controller number or 
PC.
OPE:Lists the operator number
PRI:Lists the priority number
3. To exit from the mode, press the CLEAR button.●Moving the Event Display
Move the joystick while holding down the OSD, SHIFT and
3 buttons. (3) will move to the desired direction.
●Moving the Monitor Status*
Move the joystick while holding down the OSD, SHIFT and
4 buttons. (4) will move to the desired direction.
* Monitor number, controller number and monitor mode
●Moving All the Items
Move the joystick while holding down the OSD, SHIFT and
5 buttons. (1), (2), (3), and (4) will move to the desired
direction.
■ System Status Table
The table shows the current system status.
1. Select the desired monitor. (Refer to p. 90 Monitor
Selection.)
2. Press the button 9 while holding down the OSD button.
OSD will appear on the LED display, and the SYSTEM
STATUS table will appear on the active monitor as
shown in the figure.
The columns in the table indicate the states as shown in the
figure.
MON:Monitor number
CAM:Camera number 
No number indicates no camera is  
selected.
             SYSTEM STATUS
  MON   CAM  MODE    KB    OPE  PRI
  1     01   T01     K1    1    30
  2     02   SPOT    K2    2     2
  3     04   ALARM   K4    4     1
  4     16   CAM     PC    30    1
SETUP
SHIFT
REW/FF
STEP
CALL
PRESET
PROGRAM
PRESET
GROUP SEQ
PAUSE
SUSPEND
F1
CAM SETUPALL RESET
ACKRESET
F2
TOUR SEQ
PREVNEXT
STOP
OSD
AUTO PANRECORDER
INDEX
STOP PLAYPAUSE
CAM FUNC
CLEAR
LOG OUTMON LOCK
DEF ON
WIPER
DEF OFFMON (ESC)
T&D CAM ID
MON STATUSALLEVENT
ALM H VLD H SYS S
CAM (SET)
MULTI SCREEN SEL
SEQUENCE
AUX2 ON AUX2 OFFEL-ZOOM
AUX1 ON AUX1 OFFSTILL 
						

							101
■ Alarm History Table
There are 100 alarm records stored in chronological order
in 10 pages of tables.
1. Select the desired monitor. (Refer to p. 90 Monitor
Selection.)
2. Press the button 7 while holding down the OSD button.
OSD will appear on the LED display, and the ALARM
HISTORY table will appear on the active monitor as
shown in the figure.
The columns in the table indicate the states as follows:
DATE:Lists the date and time when the alarm state
changes.
ALARM:Lists the alarm number (01 - 16).
EVENT:Lists the event when the alarm state changes.
3. Press the NEXT button to select the next page of the
history, and press the PREV button to back up to the
previous page.
4. To exit from the mode, press the CLEAR button.
■ Video Loss History Table
There are 100 video loss detection records stored in
chronological order in 10 pages of table.
1. Select the desired monitor. (Refer to p. 90 Monitor
Selection.)
2. Press the button 8 while holding down the OSD button.
OSD will appear on the LED display, and the VIDEO
LOSS HISTORY table will appear on the active monitor
as shown in the figure  below.
The columns in the table indicate the states as follows:
DATE:Lists the date and time when the video loss
state changes.
CH:Lists logical camera number that is connected
to the system.
EVENT:Lists the event when the video loss state
changes.
             ALARM HISTORY      1 of 2
NO  YYYY/MM/DD HH:MM:SS  ALARM  EVENT
016 2001/08/21 18:59:08  03     ALARM
015 2001/08/21 18:58:08  03     ACK
014 2001/08/21 18:57:08  03     RESET
013 2001/08/21 18:55:08  07     ALARM
012 2001/08/21 18:54:08  07     ACK
011 2001/08/21 18:53:08  07     RESET
010 2001/08/21 18:53:00  09     ALARM
009 2001/08/21 18:52:08  09     RESET
008 2001/08/21 18:51:08  06     ALARM
007 2001/08/21 18:50:08  06     ACK
SETUP
SHIFT
REW/FF
STEP
CALL
PRESET
PROGRAM
PRESET
GROUP SEQ
PAUSE
SUSPEND
F1
CAM SETUPALL RESET
ACKRESET
F2
TOUR SEQ
PREVNEXT
STOP
OSD
AUTO PANRECORDER
INDEX
STOP PLAYPAUSE
CAM FUNC
CLEAR
LOG OUTMON LOCK
DEF ON
WIPER
DEF OFFMON (ESC)
T&D CAM ID
MON STATUSALLEVENT
ALM H VLD H SYS S
CAM (SET)
MULTI SCREEN SEL
SEQUENCE
AUX2 ON AUX2 OFFEL-ZOOM
AUX1 ON AUX1 OFFSTILL
          VIDEO LOSS HISTORY    1 of 2
NO  YYYY/MM/DD HH:MM:SS  CH EVENT
012 2001/08/21 18:59:08  03 VIDEO RECOVER
011 2001/08/21 18:58:08  14 VIDEO RECOVER
010 2001/08/21 18:57:08  09 VIDEO LOSS
009 2001/08/21 18:55:08  07 VIDEO LOSS
008 2001/08/21 18:54:08  08 VIDEO LOSS
007 2001/08/21 18:53:08  16 VIDEO LOSS
006 2001/08/21 18:53:00  09 VIDEO LOSS
005 2001/08/21 18:52:08  14 VIDEO LOSS
004 2001/08/21 18:51:08  06 VIDEO LOSS
003 2001/08/21 18:50:08  01 VIDEO RECOVER
        
SETUP
SHIFT
REW/FF
STEP
CALL
PRESET
PROGRAM
PRESET
GROUP SEQ
PAUSE
SUSPEND
F1
CAM SETUPALL RESET
ACKRESET
F2
TOUR SEQ
PREVNEXT
STOP
OSD
AUTO PANRECORDER
INDEX
STOP PLAYPAUSE
CAM FUNC
CLEAR
LOG OUTMON LOCK
DEF ON
WIPER
DEF OFFMON (ESC)
T&D CAM ID
MON STATUSALLEVENT
ALM H VLD H SYS S
CAM (SET)
MULTI SCREEN SEL
SEQUENCE
AUX2 ON AUX2 OFFEL-ZOOM
AUX1 ON AUX1 OFFSTILL 
						

							102
■Operating during an Alarm Mode
While an alarm mode is active, the following are available
from the system controller:
•Operating the camera with the alarm input (ACK)
•Resetting the alarm (RESET/ALL RESET)
•Suspending the alarm (ALM SUSPENDED)
■Operation of an Alarm-related
Camera (ACK)
You can operate the camera with the alarm input as follows:
1. Select a monitor which displays ALARM.
2. Press the ACK button.
ACK will appear on the monitor with an alarm input.
The camera with an alarm input will become operable.
3. Operate camera with the system controller.
Pan/Tilt, zoom, focus, and iris are available.
When selecting another monitor, ACK will disappear
from the display. The matrix switcher system will return
to the alarm mode.
MON LOCK
DEF ON
WIPER
DEF OFFMON (ESC)
T&D CAM ID
MON STATUSALLEVENT
ALM H VLD H SYS S
CAM (SET)
MULTI SCREEN SEL
SEQUENCE
AUX2 ON AUX2 OFFEL-ZOOM
AUX1 ON AUX1 OFFSTILL
SHIFT
REW/FF
STEP
GROUP SEQ
PAUSE
SUSPEND ALL RESET
ACKRESET
TOUR SEQ
PREVNEXT
OSD
PLAYPAUSE
■Alarm Mode
When alarm (sensor) is accepted, the matrix switchers
operation mode changes to the alarm mode.  Then, the sys-
tem operates as follows:
•The camera image (alarm image) appears on the moni-
tor.
In the factory default setting, the alarm inputs 1 to 16
are associated with the same-numbered camera input
connectors. All the video output signals are sent to
Monitor 1. For example, when the alarm (sensor) con-
nected to the alarm input 1 becomes active, the camera
input connector 1’s image appears on Monitor 1.
•ALARMnn appears on the monitor.
The display indicates the image is input through the
alarm nn (nn is the alarm number).
When more than one alarm signal input has been
accepted, ALARMnn
* appears on the monitor.
•Alarm output signals are supplied from Alarm Output 1
to 4 (#10, 11, 23 and 24) of the ALARM port (25-pin D-
sub connector) at the rear panel. Alarm Output 1 to 4 is
associated with MONITOR OUT 1 to 4. For example,
when an alarm input signal is activated on MONITOR
OUT 1, the unit supplies Alarm Output 1 to Monitor 1.
•The monitor and alarm number will appear on the LED
display. At the same time, the alarm indicator will blink,
the monitor indicator will light up, and the camera indi-
cator will go out.
There are two operation mode when more than one
alarm signal has been accepted by the unit that is
assigned to the same monitor.
• Sequence mode:An alarm operation is replaced by
another one after the dwell time ends.
• Hold mode:An initial alarm operation is continued
even after another alarm input is accepted.
Notes:
•The association of the alarm inputs with cameras and
monitors are changeable in SETUP MENU or WJ-SX150
Administrator Console. (Refer to p. 56 or p. 74.)
•Alarm input will be automatically reset in 30 seconds.
The auto-recovery time is configurable through SETUP
MENU or WJ-SX150 Administrator Console.
ALARM CONTROL
ALARM01
ACK