Panasonic Matrix Switcher Wj Sx150 Operating Instructions

							●To Record the Camera Images in Maximum
Recording Rate
The following is the description of the connection between a
recorder and this unit for the maximum-rate recording.
1.Set the unit address of the recorder to 1. Then, set the
recorder’s CAMERA GENLOCK to ON in its SETUP
MENU. (Refer to the recorders operating instructions.)
2.Connect the unit’s CAM OUT 1 to 16 connectors to the
recorder’s VIDEO IN 1 to 16 connectors with a coaxial
cable.
3.Connect the unit’s EXT IN connector to the recorder’s
GENLOCK OUT connector with a coaxial cable.
4.Connect the unit’s DATA HDR connector to the
recorder’s DATA port with a modular cable.
(The control data and alarm signal will be output from
the unit to the recorder.)
5.After the connection, set the unit’s EXT IN to GENLOCK
ON through SETUP MENU or WJ-SX150 Administrator
Console (Refer to pp. 60 or 66).
Notes:
•You need WJ-HD500A or a newer model for the maxi-
mum-rate recording.
•The playback, multiscreen output or live images from the
recorder are not displayed on Monitor 1 to 4. To confirm
the images, you need to connect another monitor with
the recorder. 
•The recorder will not operate if its unit address is set to
other than 1.
•Make sure the DATA HDR ports unit address is set to 1
through WJ-SX150 Administrator Console. (Refer to p.
66.) If another number is selected, you cannot control
the recorder.
WJ-SX150 Matrix Switcher
WJ-HD500A or a newer model
16
1615
1514
1413
1312
1211
1110
109
98
87
76
65
54
432
2
3
1
1
SIGNAL GND10/100BASE-TSPOT
OUTIN EXT STORAGE COPY
CONTROL ALARM
VIDEOMODEDATAREMOTE(WV-CU50)GEN-LOCK OUTSERIAL
INOUT
OUTMULTI SCREEN OUTAUDIO
EXT IN
GENLOCK 
OUT MULTI 
SCREEN
OUTDATA DATA HDR
Monitor
CAMERA1
1
2
2
3 3 2
DATA  3 D ATA  2SERIAL ALARM
TERM
OFF ON4
2
1
43
EXT OUT
(REC OUT)
CAMERA
SW  INRS485(CAMERA)LINE
SELECTMONITOR OUT
EXT IN
(PLAY IN)
OUT
IN
4
4
5
5
6
6
7
7
8
8
9
9
10
10
11
11
12
12
13
13
14
14
15
15
16 16
RS485(CAMERA)PS•DATA
DATA  4 DATA HDRDATA  1
42
Notes:
•You cannot record the camera images in maximum
recording rate through this connection. Refer to the next
connection example in this page.
•The recorder will not operate if its unit address is set to
other than 1. 
						

							43
●To Control a Recorder via the Network
The following is the description of the connection between
a recorder and this unit to control the recorder via the net-
work.
1. Set the recorders unit address to a number 5 or larger .
(Refer to the recorders operating instructions.)
2. Connect the unit’s CAM OUT 1 to 16 connectors to the
recorder’s VIDEO IN 1 to 16 connectors with a coaxial
cable.
3. Connect the unit’s DATA HDR and DATA4 connectors
to the recorder’s DATA port with a daisy chain connec-
tion cable kit (WV-CA48/10K).
(The control data and alarm signal will be output from
the unit to the recorder.)
4. Select the recorders new unit address, which is set in
step 1, for DATA HDR in the Data Port window. (Refer to
p. 66.)
5. Through a browser, set the unit address of an optional
network board (WJ-HDB502) to a number other than 1.
(Refer to WJ-HDB502 Operating Instructions.) 
6. Refer to p. 39, p. 41 and p. 42 for MONITOR OUT con-
nection, MULTI SCREEN OUT connection, and EXT IN
connection.
43
Notes:
•You will need WJ-HD500A or a newer model, in which
an optional network board (WJ-HDB502) is installed.
•Select the PS·Data protocol for the DATA 4 setting.
(Refer to p. 61 DATA 4/PSD PORT SELECT or p. 81
Data Port.) If the terminal mode is selected, you cannot
control the recorder.
•The recorder will not be operable if its unit address is
set to 1.
•If the recorders unit address in step 1 and the DATA
HDR setting in step 4 are different, the recorder will not
be operable.
•In these connections, you cannot use a PS·Data system
controller.
WJ-SX150 Matrix SwitcherMonitor
 Digital Disk Recorder*
16
1615
1514
1413
1312
1211
1110
109
98
87
76
65
54
432
2
3
1
1
SIGNAL GND10/100BASE-TSPOT
OUTIN EXT STORAGE COPY
CONTROL ALARM
VIDEOMODEDATAREMOTE(WV-CU50)GEN-LOCK OUTSERIAL
INOUT
OUTMULTI SCREEN OUTAUDIO
* WJ-HD500A or Newer Models with Network Board (WJ-HDB502)
** LAN : Local Area Network
CAMERA1
1
2
2
3 3 2
DATA  3 D ATA  2SERIAL ALARM
TERM
OFF ON4
2
1
43
EXT OUT
(REC OUT)
CAMERA
SW  INRS485(CAMERA)LINE
SELECT
MONITOR OUT
EXT IN
(PLAY IN)
OUT
IN
4
4
5
5
6
6
7
7
8
8
9
9
10
10
11
11
12
12
13
13
14
14
15
15
16 16
RS485(CAMERA)PS•DATA
DATA  4 DATA HDRDATA  1
EXT IN
MULTI SCREEN 
OUTDATA HDR
DATA
DATA4
(PS·Data)
MONITOR
OUT
Daisy Chain Connection Kit
(WV-CA48/10K)
HUB/Router
LAN cable
10/100 BASE-T
LAN** 
						

							■ Connection with Digital Disk Recorder WJ-HD100 Series
1. To record the camera images with Digital Disk Recorder WJ-HD100 Series, install an optional Multiplexer board in the
matrix switcher.
2. Connect the matrix switcher’s EXT OUT (REC OUT) to the digital disk recorder’s VIDEO IN with a coaxial cable.
3. Connect the matrix switcher’s EXT IN (PLAY IN) to the digital disk recorder’s MONITOR OUT (PLAY) with a coaxial cable.
4. Connect the matrix switcher’s DATA HDR to the digital disk recorder’s DATA with a modular cable.
5. Connect the matrix switcher’s CAMERA SW IN to the digital disk recorder’s CAMERA SW OUT with an RCA-pin cable.
6. Select “HD100” for 610 RECORDER CONTROL in SETUP MENU. (Refer to p. 60.)
7. Conform the parameter of 740 PSD PORT SPEED to the setting of the recorder.
The following parameters are fixed.
Data bit:8 bits
Parity check:None
Stop bit:1 bit
8Conform the parameter of 620 RECORDER UNIT ADDRESS in SETUP MENU to the setting of the recorder. (Refer to the
recorder’s operating instructions for the unit address.)
Note:After the connection, configure the system through SETUP MENU and WJ-SX150 Administrator Console.
●DATA HDR Port
44
WJ-HD100 series Digital Disk Recorder
SIGNAL GND
ALARM SERIES
RECORD TIME
ADJUST
REMOTEMODE DATA RS-232C VIDEO OUTIN
OUTIN
AUDIOMONITOR OUT
(PLAY) CAMERA
SW  OUT
G
G
G
POWER
ON
OFF
JOG-CLICK
JOG-LEFT
JOG-RIGHTALARM SEARCHSTEP
REW/FF
STOP/SETUP
PLAY
REC
OUT
PLAY OUT
REC OUTAUTO OFF OUTDISK END OUT IN
OUT
IN
RECALL (EXT REC)
OUTRECOVER OUTRESET IN
IN
WJ-SX150 MatrixSwitcherPin #10 (Alarm Out 1)
Pin #11 (Alarm Out 3)
2DATA  3 D ATA  2SERIAL ALARM
TERM
OFF ON42 14
3
CAMERA
SW  INRS485(CAMERA)LINE
SELECT
MONITOR OUT
EXT IN
(PLAY IN)
EXT OUT
(REC OUT)RS485(CAMERA)
DATA  4 DATA HDR
PS•DATADATA  1
Pin #24 (Alarm Out 4) Pin #13 
(Recover Input)
Pin #23 (Alarm Out 2)
Pin #9 (GND)
TB
TA
RBRAGND
GNDMatrix switchers rear panel
DATA HDR
TB
TA
RB
RA
DATA HDR Port 
						

							45
■Connection with the Time-lapse VCR (Panasonic Models)
1. Configure the parameters of the multiplexer functions in the Multiplexer Mode (refer to p. 82) window of WJ-SX150
Administrator Console.
Note:When VCR is selected in 610 RECORDER CONTROL in SETUP MENU (refer to p. 60), parameter configuration in the
Multiplexer Mode window is unavailable.
2. Select VCR for 610 RECORDER CONTROL in SETUP MENU. (Refer to p. 60.)
3. Conform the communication speed (COMM. SPEED) for 750 SERIAL PORT SPEED in SETUP MENU to that of the time-
lapse VCR. (Refer to p.61.)
The following parameters are fixed.
Data bit:7 bits
Parity check:ODD
Stop bit:1 bit
4. Connect the matrix switcher’s EXT OUT (REC OUT) to the time-lapse VCR’s VIDEO IN with the coaxial cable.
5. Connect the matrix switcher’s EXT IN (PLAY IN) to the time-lapse VCR’s VIDEO OUT with the coaxial cable.
6. Connect the matrix switcher’s SERIAL to that of the time-lapse VCR with a 9-pin D-sub cable.
7. Connect the matrix switcher’s CAMERA SW IN to the time-lapse VCR’s CAMERA SW OUT with an RCA-pin cable.
Notes:
•Only Panasonic time-lapse VCRs which support RS-232C are usable. (Refer to Cable Specifications on the next page
for details of cables.)
•Both of the time-lapse VCR and PC cannot be connected to the matrix switcher.
•When configuring the system through WJ-SX150 Administrator Console, pull out the time-lapse VCR’s cable and con-
nect the PC’s cable to the serial port.
•To use the alarm recording function, connect the matrix switcher’s all alarm output terminals (Alarm Output 1 to 4) to
the time-lapse VCR’s ALARM IN.
•Be sure to activate auto-recovery for the VCR’s alarm reset function.
VIDEO IN
CAMERA
SW  OUTGND
S-VIDEO
AUDIOVIDEO OUT
12
12345678910111213141516
1
2
3
4
ALARM
IN
COMALARM
RESET IN
ALARMRECOVER OUT
5
6
7
8
ALARM
OUT
1 SHOT IN
TAPE END
OUT
9
10
11
12
WARNING
OUT
HUMID OUT
REC REVIEWOUT
13
14
15
16
SERIES
REC IN
TIME
ADJUST IN
TIMEADJUST OUT
COMREC OUT
SERIES
REC OUT
Time Lapse VCR WJ-SX150 MatrixSwitcher
2DATA  3 D ATA  2SERIAL ALARM
TERM
OFF ON42 14
3
CAMERA
SW  INRS485(CAMERA)LINE
SELECT
MONITOR OUT
EXT IN
(PLAY IN)
EXT OUT
(REC OUT)RS485(CAMERA)
DATA  4 DATA HDR
PS•DATADATA  1
Pin #23(Alarm out 2)
Pin #9(GND)
Pin #24(Alarm out 4)
Pin #10(Alarm out 1)
Pin #11(Alarm out 3)
Pin #13 
(Recover Input)
4 
						

							46
■Connection with the Time-lapse VCR (Non-Panasonic Models)
1. To record the camera images through a time-lapse VCR, install an optional Multiplexer board in the matrix switcher.
2. Select OFF for 610 RECORDER CONTROL in SETUP MENU.
3. Connect the matrix switcher’s EXT OUT (REC OUT) to the time-lapse VCR’s video input connector with the coaxial cable.
4. Connect the matrix switcher’s EXT IN (PLAY IN) to the time-lapse VCR’s video output connector with the coaxial cable.
Notes:
•To use the alarm recording function, connect the matrix switcher’s all alarm output terminals (Alarm Output 1 to 4) to the
time-lapse VCR’s ALARM IN.
•Refer to p. 45 “Connection with the Time-lapse VCR (Panasonic Models) ” for the illustration.
•Be sure to set the VCR to automatically recover from alarm reset.
VIDEO IN
CAMERA
SW  OUTGND
S-VIDEO
AUDIOVIDEO OUT
12
12345678910111213141516
1
2
3
4
ALARM
IN
COMALARM
RESET IN
ALARMRECOVER OUT
5
6
7
8
ALARM
OUT
1 SHOT IN
TAPE END
OUT
9
10
11
12
WARNING
OUT
HUMID OUT
REC REVIEWOUT
13
14
15
16
SERIES
REC IN
TIME
ADJUST IN
TIMEADJUST OUT
COMREC OUT
SERIES
REC OUT
Time Lapse VCR WJ-SX150 MatrixSwitcher
2DATA  3 D ATA  2SERIAL ALARM
TERM
OFF ON42 14
3
CAMERA
SW  INRS485(CAMERA)LINE
SELECT
MONITOR OUT
EXT IN
(PLAY IN)
EXT OUT
(REC OUT)RS485(CAMERA)
DATA  4 DATA HDR
PS•DATADATA  1
Pin #23(Alarm out 2)
Pin #9(GND)
Pin #24(Alarm out 4)
Pin #10(Alarm out 1)
Pin #11(Alarm out 3)
Pin #13 
(Recover Input)
4
■Cable Specifications
1
2
3
4
5
6
7
8
9
Frame1
2
3
4
5
6
7
8
20
22
Frame
Shield
WJ-SX150 T/L VCR
AG6730, AG6740
1
2
3
4
5
6
7
8
91
2
3
4
5
6
7
8
9
Straight Cable
RT850 WJ-SX150
RT850 
						

							47
■Connection with the PC
1. Conform the communication speed (SERIAL PORT
SPEED) parameter in SETUP MENU to that of the PC.
2. Connect the matrix switchers serial port to that of the
PC with the 9-pin D-sub cable.
Notes:
•The following parameters are fixed.
Data bit:8 bits
Parity check:none
Stop bit:1 bit 
•Refer to Cable Specifications in this page for details on
cables. 
●Cable Specifications
1
2
3
4
5
6
7
8
Frame1
2
3
4
5
6
7
8
Frame
Shield
PC WJ-SX150
SERIAL
Personal Computer Matrix Switcher
D-sub9 D-sub9
or
D-sub25
■Time Adjustment with an External
Equipment
The specified external devices can output the time adjust-
ing signal to the matrix switcher.
This signal can adjust the time by up to ± 30 seconds every
hour. 
To use this function, it is necessary to assign one of the
alarm input terminals (pin # 1 to 16) to the time adjusting
terminal.
SETUP MENU or WJ-SX150 Administrator Console can
assign the signal.
●Master Clock Connection Example for Time
Adjustment
Connect the matrix switchers time adjusting terminal to
those of the master clock with the twisted pair cable.
The figure below shows the case in which Alarm Input 16 is
assigned as the time adjusting terminal.
Note: A master clock with N.O. (Normally Open alarm con-
tact)-type output is connectable.
12
63 9
Master clockMatrix Switcher
ALARM
Pin #21
Pin #22
GND 
						

							49
WJ-SX150 SETUP PROCEDURES 
						

							50
SETUP PROCEDURES
■Setup Procedures
This unit has two setting procedures.
The one is SETUP MENU, which is the units on-screen dis-
play (OSD).
The other is WJ-SX150 Administrator Console, which oper-
ates on the PC.
•SETUP MENU (OSD)
The basic functions, which are essential for the operation,
are configurable. However, some items are not config-
urable. The settings about group sequences, operators and
schedules, etc.
•WJ-SX150 Administrator Console (PC)
All the functions of this unit are configurable. You need a
PC to use WJ-SX150 Administrator Console.
Refer to p. 64 WJ-SX150 ADMINISTRATOR CONSOLE for
details of the platform and installation.Notes:
•To use WJ-SX150 Administrator Console, you need to
prepare a PC and a 9-pin D-sub cable.(Refer to p. 47.)
•When changing the configuration of WJ-SX150
Administrator Console, configuration data getting and
putting are necessary between the unit and PC to acti-
vate your configuration.
■Description of Setup Procedures
This chapter describes about configurable items.
●Sequence Settings
SETUP MENU can configure tour sequences. WJ-SX150
Administrator Console can configure both of tour
sequences and group sequences.
•Tour sequence: Up to 16 tour sequences are config-
urable (16 steps per tour). 
•Group sequence: Tour sequences can be activated on
up to 4 monitors simultaneously (1 tour sequence per
monitor).
●Schedule Settings
SETUP MENU can configure daylight saving time. WJ-
SX150 Administrator Console can configure timer event,
camera cleaning, and daylight saving time.
•Timer event: A sequence or spot mode can be activat-
ed on the regular time of every month, week or day.
Up to 30 timer events can be registered.
•Camera cleaning: Camera cleaning can be executed
on the regular time of every month, week or day.
•Daylight saving time: Daylight saving times for 20 years
are configurable.
●Alarm Settings
The operation parameters when an alarm is input to the unit
are configurable.
•Alarm mode: The  operation mode activated along with
an alarm input is configurable. Sequence mode or hold
mode is selectable. Alarm mode can be set to OFF
when not using it.
•Alarm event: The event activated along with an alarm
input is assignable to each alarm input terminals. The
sequence number or spot camera is selectable for the
alarm event.
•Alarm input (Alarm port): The alarm polarity (N. O. or N.
C.) is assignable to each alarm input terminal. One of
16 terminals is assignable for time adjustment.
SETUP MENU (OSD)
WJ-SX150 Administrator Console (PC)
Sequence settings
 • Tour sequence
 • Group sequence
Schedule settings
 • Timer event 
 • Camera cleaning 
 • Daylight saving time
Alarm settings
 • Alarm mode 
 • Alarm event 
 • Alarm input/Alarm port
Operator settings
 • Operator registration
 • Level table 
 • Monitor select (Monitor selection) 
 •
Auto login/logout (Auto log-in/log-out)
System settings
 • Clock (Time and date) *1 
 • Cable compensation 
 • Camera title
 • Data port *
2
Multiplxer board 
 • Recorder
 • Multiplexer *
3
 • Mux (Multiplxer camera title) *3
 
Setup file operation
 • Put a file to SX150
 •
Get a configuration data from the SX150
SX150 Admin Console Configuration 
 • File Open
 • Account Manager
 • Communication (Serial) port 
 • Camera manual cleaning ON/OFF
*
1 WJ-SX150 Administrator Console can configure the 
display pattern.
*
2 WJ-SX150 Administrator Console can configure the 
communication speed (baud rate) of the ports Data 1 to 4.
*
3 These menus (or windows) appear only when the Multiplxer 
is installed in the unit. 
						

							51
•It is also selectable whether to activate the recording
and sequence/spot image monitoring when an alarm
signal is input to the unit. Alarm recording without the
sequence/spot image monitoring is also available.
●Operator Settings
If you control this unit with a terminal-mode system con-
troller, your operator information, controllable monitors and
auto log-in/log-out will be registrable and configurable.
•Operator registration: Up to 16 operators are available.
ID and password for operator identification are config-
urable. Level and priority can be assigned to each
operator. Each cameras control coverage is also con-
figurable.
•Level table: Restriction level for each password is cus-
tomizable.
•Monitor select (Monitor selection): Controllable monitor
can be assigned to each controller.
•Auto login/logout (Auto log-in/log-out): Auto log-in/log-
out is configurable for each controller.
Notes:
•These settings (except Operator registration) are con-
figurable only through WJ-SX150 Administrator
Console. Operator registration is configurable through
SETUP MENU and WJ-SX150 Administrator Console.
•When you control the unit with a PS·Data system con-
troller, the above settings will be invalid. Refer to the
system controllers operating instructions.
●System Settings
SETUP MENU can configure the clock (time and date),
cable compensation and camera title.
Besides these settings, WJ-SX150 Administrator Console
can select the data ports baud rates.
•Clock (Time and date): The units time and date are
configurable.
•Cable compensation: Cable compensation type is
selectable depending on the distance between a cam-
era and the unit. It is also possible to determine whether
to send the VD2 timing pulse or control data with the
camera output signals.
•Camera title: Camera title is configurable to identify the
camera images on the monitor. WJ-SX150 Administrator
Console can configure the camera title including origi-
nal characters.
•Data port: Usually, the ports DATA 1 to 3 connect to the
terminal-mode system controllers. RS-485 cameras will
be connectable with the data port configurations
through WJ-SX150 Administrator Console and SETUP
MENU.
When you use the system controllers via the PS·Data
protocol, you need to configure the DATA 4 port setting
through SX150 Admin Console or SETUP MENU.
•EXT IN: External synchronization of the EXT IN connec-
tor is set to ON or OFF.
●Multiplexer
•Recorder: The type and unit address of the recorder
are configurable.
•MULTIPLEXER: The parameters of the recorder mode
are configurable. You can set the alarm and normal
recording rate. You can also activate/deactivate
dynamic recording, dummy black, and CAM SW LOSS”
indication.
•MUX (Multiplxer) CAMERA TITLE: Camera titles which
are displayed with Multiscreen segments are config-
urable.
●Setup File Operation
WJ-SX150 Administrator Console can send a configuration
file from the PC to this unit. The utility can also send the file
from the unit to the PC for configuration. 
•Put to a file: A configuration data is sent from the PC to
the unit.
•Get from a file: A configuration data is sent from the unit
to the PC.
•Select setup data file: A configuration data is selected
when sending it from the PC to the unit (or from the unit
to the PC.)
Note:These settings are configurable only through WJ-
SX150 Administrator Console.
●WJ-SX150 Administrator Console
Configuration 
The PC-related settings are configurable.
•Account Manager: WJ-SX150 Administrator Console
operators are registrable and changeable.
•Communication (Serial) port: PCs usable communica-
tion port number and its baud rate (communication
speed) are configurable. 
						

							52
WJ-SX150 SETUP MENU (OSD)
The WJ-SX150 SETUP MENU (SETUP MENU) enables func-
tion controls that are not available by direct operation.
Note: Only one operator can enter SETUP MENU.
■Displaying SETUP MENU
To display SETUP MENU, follow the procedure below.
1. Confirm that the camera and peripherals are correctly
and securely connected and that all components are
turned on.
2. To execute the selection, select one of the monitors (1
to 4) by pressing the numeric button, then press the
MON (ESC) button. 
The MONITOR indicator will light up.
3. Press the SETUP button while holding down the SHIFT
button on the system controller.
WJ-SX150 SETUP MENU will appear on the active mon-
itor as shown below, and the system controllers SETUP
indicator will light up.
The tree of SETUP MENU is shown in the next page.
Note:“x.xx” in SETUP MENU shows the firmware ver-
sion.
The following functions and buttons are valid in SETUP
MENU:
Joystick to UP(D):Moves the cursor up or returns to
the previous page.
Joystick to DOWN(C):Moves the cursor down or dis-
plays the next page.Joystick to L(A):Moves the cursor to the left.
Joystick to R (B):Moves the cursor to the right.
PREV button:Selects the previous mode or parameter.
NEXT button:Selects the next mode or parameter.
Numeric buttons:Enters numerals.
CLEAR button:Deletes a character when editing a
camera title.
CAM (SET) button:Executes the selections and dis-
plays a submenu for items with the (O) mark.
MON (ESC) button:Returns to SETUP MENU or the
previous menu.
This operating instructions uses the symbols to
describe the buttons.
4. To end the setting and return to the normal view, press
the SETUP button while holding down the SHIFT button
when SETUP MENU is displayed.
The system controllers SETUP indicator will go off.
Note:The Multiplexer board version, “900 MULTIPLEX-
ER”, and “1000 MUX CAMERA TITLE” is displayed
only when the Multiplexer board is installed in the
unit.
■ Programming SETUP MENU
As shown in the tree, SETUP MENU has seven main sub-
menus:
TIME & DATE, D. S. T., SEQUENCE SETUP, ALARM
SETUP, CAMERA TITLE, SYSTEM SETUP and OPERATOR
REGISTRATION.
SEQUENCE SETUP, ALARM SETUP, CAMERA TITLE, SYS-
TEM SETUP and OPERATOR REGISTRATION are further
divided into additional submenus.
The (O) mark indicates that the item has a submenu for
more detailed setups.
Refer to the figure in next page for the composition of
SETUP MENU.
■TIME & DATE
SETUPSHIFT WJ-SX150 SETUP MENU            x.xx/x.xx
  100 TIME&DATE     Aug/21/2002 10:55 AM
  200 D.S.T.        ON           
  300 SEQUENCE
O  400 ALARMO  500 CAMERA TITLEO  600 RECORDERO  700 SYSTEMO  800 OPERATOR REGISTRATIONO 
  900 MULTIPLEXERO 1000 MUX CAMERA TITLEO
(Without the Multiplexer board)*
(With the Multiplexer board)
* This is the factory default setting.
 WJ-SX150 SETUP MENU                 x.xx
 100 TIME&DATE      Aug/21/2002 10:55 AM
 200 D.S.T.         ON           
 300 SEQUENCE
O 400 ALARMO 500 CAMERA TITLEO 600 RECORDERO 700 SYSTEMO 800 OPERATOR REGISTRATIONO
 WJ-SX150 SETUP MENU            x.xx/x.xx
  100 TIME&DATE     Aug/21/2002 10:55 AM
  200 D.S.T.        ON           
  300 SEQUENCE
O  400 ALARMO  500 CAMERA TITLEO  600 RECORDERO  700 SYSTEMO  800 OPERATOR REGISTRATIONO
  900 MULTIPLEXERO 1000 MUX CAMERA TITLEO