Panasonic Matrix Switcher Wj Sx150 Operating Instructions

125
This section will describe what you should take notice when using a PS·Data system controller. 
The same descriptions as the system controllers operating instructions are not mentioned here. Refer to them.
Refer the descriptions of terminal mode for illustrations.
■Controlling the Recorder with a PS·Data System Controller
●Recorder Mode
Before operating the recorder, it is necessary to enter the recorder mode.
1. Select the desired monitor. (Refer to p. 109 Monitor Selection.)
2. Enter 111 by...

126
This section will describe what you should take notice when using a PS·Data system controller. 
The same descriptions as those of digital disk recorders are not mentioned here. Refer to p.xx for details.
Notes:
•Before the use, it is necessary to install the Multiplexer board in the matrix switcher, connect the matrix switcher to the
time-lapse VCR, and configure the system through WJ-SX150 Administrator Console, OSD SETUP MENU, and time-lapse
VCRs SETUP MENU. [Refer to p. 34 Installing the...

127
MONITOR DISPLAY WHEN A VIDEO LOSS OCCURS
■Video Loss Display
•When video loss of CAMERA IN nn (nn is a number) is
detected,  LOSS CH nn will blink on the monitor.
•When more than one LOSS CH have occurred, LOSS
CH nn* will appear on the monitor.
•When the input loss is recovered, LOSS CH nn will dis-
appear from the monitor.
•When you press the RESET button while pressing the
OSDbutton, LOSS CH nn will disappear from the
monitor.
■Camera Switching Pulse Loss
Display
•When loss of the camera switching...

128
TROUBLESHOOTING
Check to see the following before request for repair.
If a trouble cannot be removed even after checking and trying remedy, contact your dealer.
Problem Check item Remedy
Matrix switcher does not power up. The power cord may be disconnected
either from the units power socket or
the AC outlet.Connect the power cord between the
unit
s power socket and the AC outlet.
System controller(s) do (does) not log
in.The unit’s power cord may be discon-
nected from the AC outlet.Connect the power...

129
The camera image is dim. Dust may be sticking on the camera
lens.Remove the dust from the camera lens. 
The camera’s lens focus may not be
proper.Press the FOCUS NEAR/ FAR buttons
to adjust the lens focus. If the camera
supports auto focus, press these but-
tons simultaneously. The lens focus can
be adjusted automatically.
The camera’s cable compensation set-
ting may not be proper.Open 710 COMPENSATION/VD2/DATA
(refer to p. 60) or the Cable Compensa-
tion/VD2 window (refer to p. 78) to con-
firm the...

130
The alarm mode is not activated.
The alarm mode is set to OFF. Set the alarm mode to SEQUENCE or
HOLD in SETUP MENU or WJ-SX150
Administrator Console.
SETUP MENU: Refer to p. 52.
Adminstrator Console: Refer to p. 64.
The port for an alarm input is set to
OFF.Set the alarm port to ON in SETUP
MENU or WJ-SX150 Administrator
Console.
SETUP MENU: Refer to p. 52
Administrator Console: Refer to p. 64.
When ALM SUSPENDED is displayed
on the monitor, the alarm is suspended.Press the ACK/SUSPEND button while...

131
APPENDIX 

132
[STX]   [Response Command] : [E] [R] [n1] [n2] [n3] [ETX] Parameters are omitted when the command format includes neither data nor status to send back.
(2) Reception Error
The unit sends back NAK code 15H, followed by the parameters. The unit then resets the reception buffer and enters the
waiting mode for the next message. Parameter e identifies the error status. [p] stands for parameter. Parameters are omitted when the command does not need to specify them.
2. Response Command
The unit returns...

133
Pausing sequence
(PAUSE)
Stopping sequence
(STOP)
Sequence increment
(NEXT)
Sequence decrement
(PREV)
Transmission command toggles priority lock
ON or OFF.
mm=Monitor No.
n=0 (OFF)
n=1 (ON) Starting tour sequence
■Command Table
Item Response (ASCII) Parameter (ASCII)
Log-in CMD:Wnnnnn-ppppp ANS:WOK (When OK)
ANS:WNG (When NG)nnnnn= Operator number
ppppp= Password
Log-out CMD:H00LG ANS:H00LG
Monitor Selection CMD:HmmMS ANS:HmmMSmm=Monitor No.
Camera SelectionCMD:HmmCScc
CMD:HmmCS+1...

134
Alarm ACK
(Each monitor)CMD:HmmAK ANS:HmmAKmm=Monitor No. Item
Alarm input OAIcc No responsecc=Alarm No. Transmission Command
(ASCII)Response (ASCII) Parameter (ASCII)
Alarm reset
(Each monitor)CMD:HmmAR ANS:HmmARmm=Monitor No.
Alarm all reset CMD:H00AR ANS:H00AR
Alarm suspension MAD MADnTransmission command toggles alarm sus-
pension ON or OFF.
n=0  OFF
n=1  ON
Alarm Control
Return to normal view* CMD:HmmSE ANS:HmmSEmm=Monitor No.
*Available only in SETUP MENU Item
Display SETUP MENU CMD:HmmSS...