Panasonic Matrix Switcher Wj Sx150 Operating Instructions

115
EXPANDED FUNCTION 

116
WJ-HD500 SERIES CONTROL (TERMINAL MODE)
Matrix switcher can control Digital Disk Recorder WJ-
HD500 Series. The following is the procedure of WJ-HD500
Series SETUP MENU.
Notes:
•The following operating procedures are for the terminal
mode. If you are using a PS·Data system controller,
refer to p. 124.
•When a Multiplexer board is installed in the unit, you
can neither connect nor control a WJ-HD500 Series
recorder. You need to remove the board from the unit.
■Displaying WJ-HD500 Series SETUP
MENU
To...

117
•The indicator beside the RECORDER button will
light up, and the images from the recorder are dis-
played on the active monitor in multiscreen seg-
ments.
•The CAMERA indicator will go out and the monitor
number with -H00 will appear on the LED display.
3. To exit from the recorder mode, select the camera.
(Refer to p. 91 Camera Selection.) The indicator beside
the button will go out. The monitor number and camera
number will appear on the LED display again.
You can also exit from the recorder mode...

118
●Manual Recording
1. Enter the recorder mode (Refer to p. 116 Recorder
Mode.)
2. To start recording, press the WIDE and TELE buttons
simultaneously.
The digital disk recorder will start recording.
3. To stop the recording, press the STOP button while
holding down the SHIFT button.
Note:Refer to WJ-HD500 Series Operating Instructions
for details and other recording modes. 
●Search Playback
You can search playback images using the Record List or
Thumbnail Display. Every time you press the INDEX...

119
●Multiscreen Sequence
Digital disk recorder starts a sequence according to the
setting of WJ-HD500 Series.
1. Enter the recorder mode (Refer to p. 116 Recorder
Mode.)
2. Press the button 7 while holding down the SHIFT but-
ton.
3. To cancel the sequence, press the button 0 while hold-
ing down the SHIFT button.
The display will change into the multiscreen display.
●Other Operations
SHIFT + ZOOM WIDE buttons: Selects a group to be 
SHIFT + ZOOM TELE buttons:Changes the display mode
of the Record List...

120
WJ-HD100 SERIES CONTROL (TERMINAL MODE)
Digital Disk Recorder WJ-HD100 Series are operable with
the system controller, while connecting to the matrix switch-
er.
Note:Before the use, it is necessary to install the multi-
plexer board in the matrix switcher, connect the
matrix switcher to the digital disk recorder, and con-
figure the system through WJ-SX150 Administrator
Console, OSD SETUP MENU, and WJ-HD100 Series
SETUP MENU. [Refer to p. 34 Installing the
Multiplexer Board, p.44 Connection with...

121
•ALARM RECALL table
The recorder’s alarm history will be displayed on the
ALARM RECALL table.
Move the cursor with the joystick to the desired alarm
number, and then press the PLAY button. The associat-
ed image will be played back.
•Date-and-time entry form
Note:To cancel the entry form, press the CLEAR but-
ton.
1. Press the numeric buttons to enter the date and time
written down in step 2. The cursor can be adjusted by
moving the joystick rightward or leftward.
2. Press the PLAY button. After the...

122
TIME-LAPSE VCR CONTROL [PANASONIC MODELS] (TERMINAL MODE)
A time-lapse VCR (Panasonic Models) is operable with the
system controller, while connecting to the matrix switcher.
Note:Before the use, it is necessary to install the
Multiplexer board in the matrix switcher, connect
the matrix switcher to the time-lapse VCR, and con-
figure the system through WJ-SX150 Administrator
Console, OSD SETUP MENU, and time-lapse VCRs
SETUP MENU. [Refer to p. 34 Installing the
Multiplexer Board, p. 45 Connection...

123
TIME-LAPSE VCR CONTROL [NON-PANASONIC MODELS] (TERMINAL MODE)
A time-lapse VCR is operable with the system controller,
while connecting to the matrix switcher.
Notes:
•Before the use, it is necessary to install the
Multiplexer board in the matrix switcher, connect
the matrix switcher to the digital disk recorder, and
configure the system through WJ-SX150
Administrator Console, OSD SETUP MENU, and
time-lapse VCRs SETUP MENU. [Refer to p. 34
Installing the Multiplexer Board, p. 46 Connection
with the...

124
This section will describe what you should take notice when using a PS·Data system controller. 
The same descriptions as the system controllers operating instructions are not mentioned here. Refer to them.
Refer the descriptions of terminal mode for illustrations.
■Controlling the Recorder with a PS·Data System Controller
●Recorder Mode
Before operating the recorder, it is necessary to enter the recorder mode.
1. Select the desired monitor. (Refer to p. 109 Monitor Selection.)
2. Enter 111 by...