Panasonic Kx-tvs90 Voice Processing System Installation Manual

SYSTEM ADMINISTRATORS GUIDE
Installation Manual 291
To program the following 10 Parameters in the next table, use the Special Commands and Dial 
Codes listed below. You can set up to 12 digits for each parameter.
D: Disconnecting
F: Hook Flash
R: Ringback Tone Detection
S: Silence Detection
T: Dial Tone Detection
W: Wait for 1 s
X: Extension dialing
A: Answer
1-9, 0,  , #: Dial Codes
Table 75 
Parameter Value Range
(Default)Description/Function
Operator 
Transfer 
Sequence(FX)The VPS performs this...

SYSTEM ADMINISTRATORS GUIDE
292 Installation Manual
Inband Signaling Parameters
Use these parameters if the PBX sends touchtones to the VPS to indicate the state of a call 
(busy, answered, disconnected, etc.). The integration mode must be set to Inband. If PBX 
type is set to a KX-T series telephone system, the Inband Signaling parameters will 
automatically default to the proper codes.
The following parameters can be programmed using 0-9,  , #, and A-D.Call Waiting 
Sequence(1)The VPS carries out this...

SYSTEM ADMINISTRATORS GUIDE
Installation Manual 293
Note
Default values in the above table vary depending on the settings of PBX type and Inband 
Integration (PBX Interface Parameters).
N/A: Not availableForward to VM 
Busy(7)Sent to the VPS if the called extension is forwarded to a 
voice mail port and that voice mail port is not available to 
accept the call.
Forward to 
Other 
Extension(8)Sent to the VPS if the called extension is forwarded to 
another, non-Voice Mail extension.
Confirmation
(9)Sent...

SYSTEM ADMINISTRATORS GUIDE
294 Installation Manual
Digit Translation Table Parameters
Use the Digit Translation Table to translate the Follow On ID Signal from the PBX into the 
proper codes for the VPS. This translation table is only effective for the incoming signal.
Digit Translation Table Parameters-Inter-Digit Timeout
Digit Translation Table Parameters-Input/Output
To access the proper menu for Digit Translation Table Parameters, follow the menu 
path as shown:
System Administration Top...

SYSTEM MANAGERS GUIDE
Installation Manual 295
Appendix C
SYSTEM MANAGERS GUIDE 

SYSTEM MANAGERS GUIDE
296 Installation Manual
C1 ACCESSING THE SYSTEM MANAGERS 
MAILBOX
The System Managers Mailbox must be accessed before performing any System Manager 
task. To access the System Managers Mailbox, three items of information must be known: the 
telephone number connected directly to the Voice Mail Service, the System Managers 
Mailbox Number and the Password for that mailbox (if assigned). The System Managers 
Mailbox Number is 99, 999 (default), 9999 or 99999 depending upon the mailbox...

SYSTEM MANAGERS GUIDE
Installation Manual 297
C2 SETTING UP MAILBOXES
The System Managers primary function is to create mailboxes for new subscribers and to 
maintain system organization by deleting unneeded passwords and mailboxes.
Note
While the System Administrator programs via a personal computer, the System Manager 
cannot set up mailboxes. The VPS plays Sorry, this function is not available.
Creating and Editing a Mailbox
The System Manager can both create and edit Subscriber Mailboxes by following...

SYSTEM MANAGERS GUIDE
298 Installation Manual
6.Press [2] to accept the entry.
7.As each parameter plays:
a)Press [1] to enter the new parameter or [2] to leave the parameter unchanged.
b)Enter the parameter.
c)Confirm the new parameter is correct and Press [2] to accept it.
8.The All Calls Transfer to Mailbox parameter is the last parameter to be entered. When this 
entry is completed, the prompt at Step 4 will appear. Continue assigning or editing other 
mailboxes by repeating Steps 5-7.
9.To return to...

SYSTEM MANAGERS GUIDE
Installation Manual 299
Deleting a Mailbox Password
When a password is forgotten, the System Manager must delete the password before it can be 
reassigned by the subscriber.
1.Log in the Main Menu.
2.Press [6] for Other Features.
3.Press [1] for the Mailbox Setup.
4.Press [3] for Password Reset.
5.Type the mailbox number.
6.Press [1] to delete the password. 

SYSTEM MANAGERS GUIDE
300 Installation Manual
C3 SETTING COS (CLASS OF SERVICE) 
PARAMETERS
Class of Service defines the set of VPS services available to mailbox owners. A maximum of 
64 Class of Services can be established. Each Class of Service can be set using the telephone. 
COS No.63 and No.64 are assigned to the Message Manager and the System Manager 
respectively.
For a complete explanation of COS parameters, please see Table 40 and Table 41 in 
B3 SYSTEM ADMINISTRATION—SETTING COS (CLASS OF...