Panasonic Kx-tvs90 Voice Processing System Installation Manual

INTEGRATING THE VPS WITH THE PANASONIC KX-TA SERIES PBX AND KX-TD SERIES PBX
Installation Manual 91
Screen output:
The VPS tests the CPU card, the flash memory, and the
ports until 1...2...3... is displayed.
Active ports are displayed on the screen.
Screen output:
The display will alert you if System Setup is not completed successfully.
Screen output:
This message will appear when the DPT connection between the VPS and telephone 
system cannot be established.
Possible causes of the message: DPT...

INTEGRATING THE VPS WITH THE PANASONIC KX-TA SERIES PBX AND KX-TD SERIES PBX
92 Installation Manual
10. Start up completed.
a)The Power Indicator light stops blinking when the start-up has been successful. (The 
delay varies according to the system’s condition.) 
b)**ON LINE MODE** is displayed.
c)System prompt [>] is displayed on the screen. To enter system administration, Press 
ENTER. All parameters can be set through the menu-driven program.
11. Go to the System Administration Top Menu. Select [5]...

INTEGRATING THE VPS WITH THE PANASONIC KX-TA SERIES PBX AND KX-TD SERIES PBX
Installation Manual 93
4.4.2 KX-TD1232 Software Verification and Programming for DPT 
Integration via the Operating and Maintenance Tool 
Follow these steps after communication between the KX-TD1232 and the programming 
software has been established. Refer to the Operating and Maintenance manual for 
connection information. 
1.Check the software version.
a)Go to the Main Menu. Press the ALT key and the letter [V] at the same...

INTEGRATING THE VPS WITH THE PANASONIC KX-TA SERIES PBX AND KX-TD SERIES PBX
94 Installation Manual
2.Go to the Main Menu. Choose System Data Programming (BATCH [1] or 
INTERACTIVE [2]). 
Main Menu
3.Choose System from the System Data Programming Main Menu.
System Data Programming Main Menu
4.Choose Voice Mail Integration from the System Menu.
System Menu
5.First, enter the port numbers that will be connected to the VPS. If desired, change the 
default extension numbers of the Voice Mail ports. 
1....

INTEGRATING THE VPS WITH THE PANASONIC KX-TA SERIES PBX AND KX-TD SERIES PBX
Installation Manual 95
Voice Mail Integration
6.Step 6 should only be done if the VPS is going to answer all incoming Central Office lines 
directly. 
Return to the System Data Programming Main Menu. Select Line and then select CO 
Line Setting 1. Program all lines DIL to the first extension of the Voice Mail hunt group. 
CO Line Setting
7.Follow steps 5-11 in 4.4.1 KX-TD1232 Software Verification and Programming for DPT...

INTEGRATING THE VPS WITH THE PANASONIC KX-TA SERIES PBX AND KX-TD SERIES PBX
96 Installation Manual
4.4.3 KX-TD308 Software Verification and Programming for DPT 
Integration via the Manager’s Extension 
It is important that the KX-TD308 has the proper software level to allow DPT Integration with 
the VPS. Follow the procedures below to confirm the software level, then complete the 
required programming before starting up the VPS.
All of the following procedures must be done after entering system...

INTEGRATING THE VPS WITH THE PANASONIC KX-TA SERIES PBX AND KX-TD SERIES PBX
Installation Manual 97
3.Set PBX extension numbering using System Program [003].
4.Assign the Voice Mail Port. This program tells the PBX which jack will be connected to 
the VPS. This allows the PBX to send the proper DPT Integration information to those 
ports. 
KX-TVS90 (2 ports): assign 1 jack
From the SYS-PGM NO ? screen:
a)Enter [117].
b)Press the NEXT button (SP-PHONE).
Screen output: M: # #
c)Enter the jack number (2-8)...

INTEGRATING THE VPS WITH THE PANASONIC KX-TA SERIES PBX AND KX-TD SERIES PBX
98 Installation Manual
6.Connect the jack assigned in Step 4 to the VPS.
7.Connect your personal computer to the VPS and start your communication software (i.e., 
HyperTerminal, Procomm Plus, Smartcom...). 
Communication Parameters: 9600, 8 Bit, None, 1
8.Disconnect the power from the VPS and set the DIP Switch to position 5.
Only perform this step when initially setting up the system.
CAUTION
Setting the DIP Switch to position...

INTEGRATING THE VPS WITH THE PANASONIC KX-TA SERIES PBX AND KX-TD SERIES PBX
Installation Manual 99
The display will alert you if System Setup is not completed successfully.
Screen output:
This message will appear when the DPT connection between the VPS and telephone 
system cannot be established.
Possible causes of the message: DPT Interface Connection is not Established
10. Start up completed.
a)The Power Indicator light stops blinking when the start-up has been successful. (The 
delay varies according...

INTEGRATING THE VPS WITH THE PANASONIC KX-TA SERIES PBX AND KX-TD SERIES PBX
100 Installation Manual
Set the DIP Switch to position 0 after initialization is complete.TEST: Press the INTERCOM button and then [295]. If the VPS 
answers, you have a DPT connection.
The required programming is complete and the VPS and KX-TD308 should be able to 
communicate through DPT Integration.
We recommend that the KX-TD308 system has any optional extension cards installed and 
telephones connected before starting the...