Panasonic Kx Tva50 Programming Manual

2.5 System Parameters
Programming Manual 171
Va l u e  R a n g e
Max. 32 digits
Intercom Paging Parameters
VPS Intercom Paging functions in conjunction with the Intercom Paging feature of the PBX. It allows 
the VPS to page the called party (announce the callers name, line number, etc.) while the caller is 
placed on hold. To utilize this feature, Intercom Paging must be available for the PBX, and the VPS 
must be properly programmed. This feature is available for APT/DPT Integration only.
Intercom...

2.5 System Parameters
172 Programming Manual
T: Dial Tone Detection
,: Dial Pause for 1 s (default)
;: Dial Pause for 3 s (default)
X: Pager Dialing
0–9, , #: Dial Codes
Feature Manual References
2.2.25 Intercom Paging (APT/DPT Integration Only)
Release for Intercom Paging
Specifies the intercom paging release sequence. The settings made here must match the settings of 
the PBX. The sequence can be a combination of 7 letters and 12 dial codes.
Default
F,
Va l u e  R a n g e
Max. 16 digits consisting of...

2.5 System Parameters
Programming Manual 173
Announcement Repeat Cycle
Specifies the number of times the VPS announces the page.
Example:
I have a call for (subscribers name).
Default
1
Va l u e  R a n g e
1–3 times
Feature Manual References
2.2.25 Intercom Paging (APT/DPT Integration Only)
Intercom Paging Retry
Specifies the number of times to retry paging when the called subscriber has set Incomplete Call 
Handling to Intercom Paging and the subscriber is busy or if there is no answer.
Note
 This...

2.5 System Parameters
174 Programming Manual
Paging Code
Specifies the intercom paging code. The settings made here must match the settings of the PBX.
Note
 Each subscribers Intercom Paging Group Number is determined based on his or her COS.
Default
All groups: None
Selective (Paging Code for Group 1-32):  33 + Group No.
Va l u e  R a n g e
Max. 16 digits consisting of 0–9,  , # for all/each group
Feature Manual References
2.2.25 Intercom Paging (APT/DPT Integration Only)
Fax Management
You can program...

2.5 System Parameters
Programming Manual 175
Automatic Transfer of Incoming Fax Call
Enables or disables the detection of incoming fax calls.
Note
 The VPS can detect incoming fax signals during the first 30 seconds after it answers 
incoming calls.
Default
Disable
Va l u e  R a n g e
Disable, Enable
Feature Manual References
2.2.22 Fax Management
Main Fax Extension No.
Specifies the extension number of the main fax machine.
Default
None
Va l u e  R a n g e
2–5 digits
Feature Manual References
2.2.22...

2.5 System Parameters
176 Programming Manual
Default
10 s
Va l u e  R a n g e
5 s–60 s
Feature Manual References
2.2.22 Fax Management
Fax Manager Mailbox No.
Specifies the mailbox number of the Fax Manager. The VPS will notify the Fax Manager of the status 
of fax calls depending upon the settings of the Fax No Answer Coverage Mode and Fax Notification 
Mode parameters.
Default
None
Va l u e  R a n g e
2–5 digits
Feature Manual References
2.2.22 Fax Management
Fax No Answer Coverage Mode
Determines what...

2.5 System Parameters
Programming Manual 177
calls. The number announced is the number of received fax calls since the last time the VPS notified 
the Fax Manager.
Default
No
Va l u e  R a n g e
No: The VPS will not notify the Fax Manager when fax calls are answered. 
Mbx: The VPS will announce the number of successfully received fax calls to the Fax Manager when 
the Fax Manager logs in to his or her mailbox.
Extn: The VPS will announce the number of successfully received fax calls to the Fax Manager by...

2.5 System Parameters
178 Programming Manual
Va l u e  R a n g e
0 s–60 s
Maximum Continuous Tone Time
Specifies the length of time the VPS waits when a continuous tone is detected before it disconnects 
the call.
Default
6 s
Va l u e  R a n g e
0 s–60 s
Maximum Cyclic Tone Time
Specifies the length of time the VPS waits when a cyclic tone is detected before it disconnects the call.
Default
6 s
Va l u e  R a n g e
0 s–60 s
Maximum Call Duration
Specifies the maximum duration of calls. If the VPS detects...

2.5 System Parameters
Programming Manual 179
Outside Transfer Sequence
Call Transfer to Outside Sequence
Specifies the sequence the VPS uses to transfer calls to trunks (CO lines).
Default
FND
Va l u e  R a n g e
Max. 16 digits consisting of 0–9,  , # and special codes
D: Disconnecting
F: Hook Flash
R: Ringback Tone Detection
T: Dial Tone Detection
,: Dial Pause for 1 s (default)
;: Dial Pause for 3 s (default)
N: Telephone Number Dialing
0–9, , #: Dial Codes
Feature Manual References
2.2.7 Call Transfer...

2.5 System Parameters
180 Programming Manual
Call Transfer to Outside Reconnect Sequence on Busy
Specifies the sequence the VPS uses to reconnect the line when the transferred party is busy.
Default
F
Va l u e  R a n g e
Max. 16 digits consisting of 0–9,  , # and special codes
D: Disconnecting
F: Hook Flash
R: Ringback Tone Detection
T: Dial Tone Detection
,: Dial Pause for 1 s (default)
;: Dial Pause for 3 s (default)
N: Telephone Number Dialing
0–9, , #: Dial Codes
Feature Manual References
2.2.7 Call...