Panasonic Kx Tva50 Programming Manual

2.5 System Parameters
Programming Manual 151
4.Click OK.
Select Language
Position of AM/PM in Time Stamp
Specifies the position of the AM/PM announcement.
Default
After (when the Primary Language is set to English [US])
Va l u e  R a n g e
Before: the VPS announces AM/PM before the time, such as P.M. 3:42.
After: the VPS announces AM/PM after the time, such as 3:42 P.M..
24-h: the VPS announces the time in 24-h format, such as 15:42.
Oclock Prompt
Specifies when and if Oclock is announced.
Default
When 0...

2.5 System Parameters
152 Programming Manual
Va l u e  R a n g e
POUND, HASH
PBX Parameters
Specifies the parameters used to program the VPS for optimal signaling and performance with the 
PBX.
PBX Environment
Specifies how the VPS will initiate and control call transfers, setup outgoing calls, and control 
message waiting lamps on extensions. For KX-TVA50, the procedure for verifying the correct code 
sequences for non-Panasonic KX-T series PBX is to manually execute the sequences from a single 
line...

2.5 System Parameters
Programming Manual 153
Default
TDA/TAW
Va l u e  R a n g e
TDA/TAW, TD816/TD1232/TA1232, TD500, TD308, TA624, Other*1
Integration Mode
Specifies the method of integrating the VPS with the PBX.
Default
DPT
Va l u e  R a n g e
Inband: The PBX sends DTMF signals to the VPS to indicate the status of calls (busy, answered, 
disconnect, etc.). The DTMF code for each status must be set in the Inband Signaling Parameters; 
the settings of the PBX and VPS must match. If the PBX type is set...

2.5 System Parameters
154 Programming Manual
Va l u e  R a n g e
2–5 digits
Feature Manual References
2.4.1 Auto Configuration (APT/DPT Integration Only)
Operator Transfer Sequence
Specifies the sequence for transferring calls to an operators extension.
Default
FX
Va l u e  R a n g e
Max. 16 digits consisting of 0–9,  , # and special codes
D: Disconnecting
F: Hook Flash
R: Ringback Tone Detection
T: Dial Tone Detection
,: Dial Pause (default 1 s)
;: Dial Pause (default 3 s)
X: Extension Dialing
0–9, , #:...

2.5 System Parameters
Programming Manual 155
Default
FX
Va l u e  R a n g e
Max. 16 digits consisting of 0–9,  , # and special codes
D: Disconnecting
F: Hook Flash
R: Ringback Tone Detection
T: Dial Tone Detection
,: Dial Pause (default 1 s)
;: Dial Pause (default 3 s)
X: Extension Dialing
0–9, , #: Dial Code
Feature Manual References
2.2.1 Alternate Extension Group
Reconnect Sequence on Busy
Specifies the sequence for reconnecting to the caller if the called extension is busy.
Default
F
Va l u e  R a n...

2.5 System Parameters
156 Programming Manual
R: Ringback Tone Detection
T: Dial Tone Detection
,: Dial Pause (default 1 s)
;: Dial Pause (default 3 s)
X: Extension Dialing
0–9, , #: Dial Code
Reconnect Sequence on Refuse Call
Specifies the sequence for retrieving a call placed on hold after the extension (in Call Screening 
mode) has refused to accept it.
Default
F
Va l u e  R a n g e
Max. 16 digits consisting of 0–9,  , # and special codes
D: Disconnecting
F: Hook Flash
R: Ringback Tone Detection
T:...

2.5 System Parameters
Programming Manual 157
Light-Off Sequence for Message Waiting Lamp
Specifies the sequence for turning off the Message Waiting Lamp at an extension.
Default
None
Va l u e  R a n g e
Max. 16 digits consisting of 0–9,  , # and special codes
D: Disconnecting
F: Hook Flash
R: Ringback Tone Detection
T: Dial Tone Detection
,: Dial Pause (default 1 s)
;: Dial Pause (default 3 s)
X: Extension Dialing
0–9, , #: Dial Code
Feature Manual References
2.2.32 Message Waiting Notification—Lamp...

2.5 System Parameters
158 Programming Manual
Call Waiting Sequence
Specifies the sequence for performing Call Waiting if the called extension is busy.
Default
1
Va l u e  R a n g e
Max. 16 digits consisting of 0–9,  , # and special codes
D: Disconnecting
F: Hook Flash
R: Ringback Tone Detection
T: Dial Tone Detection
,: Dial Pause (default 1 s)
;: Dial Pause (default 3 s)
X: Extension Dialing
0–9, , #: Dial Code
Release Sequence for Call Waiting
Specifies the sequence for releasing Call Waiting.
Default...

2.5 System Parameters
Programming Manual 159
Waiting Time for Receiving Caller ID
Specifies the length of time that the VPS waits before receiving Caller ID from the PBX. This 
parameter is needed only when Enable is selected in Receiving Caller ID.
Default
0 s
Va l u e  R a n g e
0 s–10 s
Inband Signaling
Set these parameters only if the Integration Mode is set to Inband under PBX Environment. If the 
PBX type is set to a KX-T series PBX, the Inband Signaling parameters will be automatically set to 
the...

2.5 System Parameters
160 Programming Manual
Va l u e  R a n g e
Max. 16 digits consisting of 0–9,  , #, and A–D
DND
Specifies the DTMF signal used to indicate a Do Not Disturb tone. Sent to the VPS when the dialed 
extension is in Do Not Disturb mode.
Default
4
Va l u e  R a n g e
Max. 16 digits consisting of 0–9,  , #, and A–D
Answer
Sent to the VPS when the called extension answers the call.
Default
5
Va l u e  R a n g e
Max. 16 digits consisting of 0–9,  , #, and A–D
Forward to VM Ringing
Specifies...