Panasonic Kx Tva50 Programming Manual

2.5 System Parameters
Programming Manual 161
Forward to Other Extension
Specifies the DTMF signal used to indicate a Forward to Other Extension tone. Sent to the VPS when 
the dialed extension has set calls to be forwarded to another extension.
Default
8
Va l u e  R a n g e
Max. 16 digits consisting of 0–9,  , #, and A–D
Confirmation 
Specifies the DTMF signal used to indicate a confirmation tone. Sent to the VPS when the Message 
Waiting Lamp was successfully turned on or off.
Default
9
Va l u e  R a n...

2.5 System Parameters
162 Programming Manual
Translation Table (Table 1–Table 8)
Follow the steps below to edit the Translation Table
1.Click Click to edit….
2.Enter the digits sent from the PBX under Input Digit and the corresponding digits received by 
the VPS under Output Digit in the Translation Table dialog box.
3.Click OK.
Input/Output digit
Defines the input and output digits that are translated by the Digit Translation Table. Do not assign the 
same sequence of Input digits more than once; if...

2.5 System Parameters
Programming Manual 163
Dialing Parameters
Number of Digits to Access Outside Line
This parameter should match the number of digits of the Line Access Code required by the PBX when 
making outside calls.
Example:
If the PBX requires callers to dial 9 to access a trunk (CO line), this parameter should be set as 1. 
This enables the VPS to recognize that an outgoing call setup sequence is completed once the initial 
9 has been dialed (9-123-4567).
Default
1
Va l u e  R a n g e
0–8...

2.5 System Parameters
164 Programming Manual
immediately to the extensions Intercept Routing destination according to PBX 
programming, rather than return the call to the VPS.
Default
20 s
Va l u e  R a n g e
10 s–60 s
Outgoing Call No Answer Time
Specifies the length of time that the VPS waits before concluding that there is no answer at the 
outside number called.
Default
30 s
Va l u e  R a n g e
10 s–90 s
Pause Time for ,
Specifies the pause time for , used in call sequences.
Default
1000 ms
Va l u e...

2.5 System Parameters
Programming Manual 165
Default
T
Va l u e  R a n g e
Max. 16 digits consisting of 0–9,  , # and special codes
D: Disconnecting
F: Hook Flash
R: Ringback Tone Detection
T: Dial Tone Detection
,: Dial Pause for 1 s (default)
;: Dial Pause for 3 s (default)
0–9, , #: Dial Codes
Message Waiting Notification
Determines how essential Message Waiting Notification features are carried out.
Outgoing Call Ports
Specifies the port numbers used for Message Waiting Notification Device feature....

2.5 System Parameters
166 Programming Manual
Default
1-6 (KX-TVA50), 1-24 (KX-TVA200)
Va l u e  R a n g e
1–6 (KX-TVA50), 1–24 (KX-TVA200)
Feature Manual References
2.2.31 Message Waiting Notification—Device
Message Waiting Lamp Ports
Specifies the port numbers used for Message Waiting Notification Lamp feature. The VPS turns on 
the Message Waiting Lamp of the extension using the port specified in this parameter. At least 1 port 
must be specified. 
Note
 The maximum number of ports depends on the VPS...

2.5 System Parameters
Programming Manual 167
Max. Digits for Callback No.
Specifies the maximum number of digits the caller can enter as a callback number. This callback 
number will be displayed on beepers if Beeper Callback No. Entry Mode set to any values other than 
Disable (see Beeper Callback No. Entry Mode in 2.1.4 Notification Parameters).
Default
20
Va l u e  R a n g e
1–48 digits
Feature Manual References
2.2.31 Message Waiting Notification—Device
Callback No. Entry Interdigit Time-out...

2.5 System Parameters
168 Programming Manual
Programming Manual References
2.1.4 Notification Parameters
Feature Manual References
2.2.31 Message Waiting Notification—Device
External Message Delivery
Determines how essential External Message Delivery features are carried out.
Retry Times
Specifies the number of times the VPS will attempt to deliver an external message when the 
destination is busy or does not answer.
Default
3
Va l u e  R a n g e
0–9 times
Feature Manual References
2.3.11 External...

2.5 System Parameters
Programming Manual 169
Busy Delay
Specifies the length of time (in minutes) the VPS waits to try to deliver an external message again 
when the destination is busy.
Default
3 min
Va l u e  R a n g e
1 min–60 min
Feature Manual References
2.3.11 External Message Delivery Service
No Answer Delay
Specifies the length of time (in minutes) the VPS waits to try to deliver an external message again 
when the destination is not answering.
Default
60 min
Va l u e  R a n g e
60 min–120 min...

2.5 System Parameters
170 Programming Manual
Default
3 min
Va l u e  R a n g e
1 min–6 min
Feature Manual References
2.3.11 External Message Delivery Service
Max. Messages for Mailboxes
Specifies the maximum number of External Delivery Messages that can be stored in one mailbox.
Default
3
Va l u e  R a n g e
1–100 msgs
Feature Manual References
2.3.11 External Message Delivery Service
System External Message Delivery Duration Time
Specifies the maximum length of External Message Delivery calls. The timer...