Panasonic Kx Tva50 Installation Manual

•Reconnect Sequence on No Answer
Tells the VPS how to return to the caller if the called extension does not answer. PBXs differ in how they
handle this function. Test from an SLT to determine the sequence.
• Reconnect Sequence on Refuse Call
Tells the VPS how to return to the caller if the called extension ’s owner has enabled Call Screening to not
take the call. PBXs differ in how they handle this function. Test from an SLT to determine the sequence.
• Light-On Sequence for Message Waiting Lamp
This is...

Inband SignalingThese parameters are used when the  Integration Mode is set to Inband. If the PBX type is set to a KX-T
series system, these parameters will be automatically set. If another type of PBX is used, check the system ’s
Installation Manual for settings.Code
(default)Call StateSent to the Voice Mail Port When...1Ringback ToneThe extension dialed is ringing.2Busy ToneThe extension dialed is busy.
3
Reorder ToneAn invalid extension number is dialed or the call is
inadvertently connected to...

Transfer to Outside ParametersThese parameters specify how the VPS will transfer calls to trunks (CO lines) from the following services:
Custom Service, Call Transfer Service, and Personal Custom Service.
Outside Transfer Sequence
• Call Transfer to Outside Sequence
Specifies the sequence the VPS uses to transfer calls to trunks (CO lines).
• Call Transfer to Outside Reconnect Sequence on Busy
Specifies the sequence the VPS uses to reconnect the line when the transferred party is busy.
• Call Transfer to...

Sequences for Voice Mail IntegrationUse the KX-TVA Maintenance Console software to program the following sequences using the sequence
codes listed here.
PBX TypeT308
T616T1232 TA
Series
T96T336
TA1232
TD1232 TD816
TD308
TD500
TDE
TDA
TAW
Series
Other
Manufacturers
Operator
Transfer
SequenceFTXFTXFTXFTXFTXFTXFTXFXExtension
Transfer
SequenceFTXFTXFTXFTXFTXFTXFTXFXAlternate
Extension
Transfer
SequenceFTXFTXFTXFTXFTXFTXFTXFXReconnect
Sequence on
BusyF,,F,,F,,F,,F,,F,,F,,F,,Reconnect
Sequence on No...

5.3  KX-TDE, KX-TDA, and KX-TAW Series PBX
Programming for Inband Integration DPT Integration is recommended when using the VPS with a KX-TDE, KX-TDA, or KX-TAW series PBX,
however, Inband Integration is necessary when the PBX has available SLT ports but no available DPT ports.
The screen shots shown in this section are for the KX-TDA200. Programming procedures and
availability may vary by PBX model, software version, etc. Refer to the documentation included with
the PBX or consult your dealer for more...

Example Settings (1)
Program the PBX so that all trunk (CO line) calls are directed to the VPS (DIL feature).
1. Go to the  CO & Incoming Call-DIL Table & Port Setting  screen.
2. Assign the  DIL Destination  for each time mode and trunk (CO line) to a floating extension number (VPS
Port).
3. Click  Apply  to save the changed data.
Calls received on the assigned trunks (CO lines) will be directed to the VPS. The VPS will answer those calls
using the service (AA, VM, Custom Service, etc.) assigned to each...

Example Settings (2)
Program the PBX to direct incoming trunk (CO line) calls to an operator, and to then direct those calls to the
VPS when the operator does not answer.
1. Program the PBX so that incoming trunk (CO line) calls are directed to an operator (DIL feature).
a. Go to the  CO & Incoming Call-DIL Table & Port Setting  screen.
b. Assign the  DIL Destination  for each time mode and trunk (CO line) to a specific extension number
(operator extension).
c. Click  Apply  to save the changed data....

c.Click  Apply  to save the changed data.
3.Set the amount of time that passes before a call is considered to be unanswered, and therefore forwarded
to the VPS.
a. Go to the  System-Timers & Counters-CO / Extension  screen.
b. Assign the  Intercept Timer  parameter.
138Installation ManualDocument Version  3.0  2010/065.3 KX-TDE, KX-TDA, and KX-TAW Series PBX Programming for Inband Integration  

c.Click  Apply  to save the changed data.
4.Program the PBX so that it will direct intercepted calls to the VPS.
a. Go to the  Groups-VM(DTMF) Group-System Setting  screen.
b. Select  None, Answer by Mailbox , or AA as the parameter for  Intercept Routing to the VPS
Sequence .
This parameter determines which DTMF command the PBX will send to the VPS in order to select the
desired service (AA, VM, Custom Service, etc.). If using a Custom Service, select  None.
Document Version  3.0  2010/06Installation...

c.Click  Apply  to save the changed data.140Installation ManualDocument Version  3.0  2010/065.3 KX-TDE, KX-TDA, and KX-TAW Series PBX Programming for Inband Integration