Panasonic Kx Tva50 Installation Manual

4.Complete the PBX-VPS connection by following from step 1 of 4.7  Completing the PBX-VPS
Connection.
Document Version  3.0  2010/06Installation Manual1114.3 KX-TA824 PBX Programming for APT Integration  

4.4  KX-TD Series PBX Programming for DPT
Integration For KX-TD500 programming, refer to 4.5  KX-TD500 PBX Programming for DPT Integration.
Programming procedures and availability may vary by PBX model, software version, etc. Refer to the
documentation included with the PBX or consult your dealer for more information.
Note
•Do not use system programs [106] or [602] for DPT Integration.
• The next 2 sections (4.4.1  KX-TD Series PBX Programming via the Manager’s Extension and
4.4.2  KX-TD1232 Series PBX...

•If you are configuring a 2-cabinet system, all Voice Mail Ports should be assigned to either the
Master or Slave System.
From the  SYS-PGM NO ?  screen:
a. Enter  [117].
b. Press the  NEXT button (SP-PHONE).
Screen output:  M:
c. Enter the jack number  (02-64) of the port you will use for the Voice Mail.
d. Press the  STORE button.
e. Press  END (HOLD) when finished.
Note
•Jack 01 cannot be used as a Voice Mail port. A jack programmed as a Manager Extension (System
Program [006]) cannot be used in this...

b.Verify the Operating and Maintenance version being used.
Sample display:
Note •If you have an older version of the maintenance tool but have the correct ROM version in the
PBX, you may still program the KX-TD1232 but you must program using the Manager’s
Extension.
c. Verify the ROM version of the KX-TD1232.
Example:  P231U
60403XX
The underlined digits represent the software production date code (year, month, day).
For DPT Integration, the production date must be 60403 or later.
If the software version...

4.5  KX-TD500 PBX Programming for DPT IntegrationFollow the procedure below to program the VPS card(s) for DPT Integration.
Programming procedures and availability may vary by PBX model, software version, etc. Refer to the
documentation included with the PBX or consult your dealer for more information.
1. Assignment of the VPS card to be connected to the VPS
Note
•If the VPS card to which the VPS will be assigned is already installed in the KX-TD500, proceed
to step 2. If installing a new VPS card, begin...

2.Confirm the LPR version of the card and the software version of the KX-TD500.
Note
•The LPR Version must be version 2 or higher for the VPS card (101: DLC/DHLC) to which the
control channel will be assigned.
• The software version must be Q171A or higher for DPT Integration to be utilized. If the software
version of the KX-TD500 is lower than this, you may not be able to utilize some of the features
available only with DPT Integration. For more information, call National Parts Center at...

Note•All parameters except for  Attribute will disappear and the  DN (Directory Number) will be cleared.
4. Assignment of the VPS card and its model
a. Go to the  1-4 VPS (DPT) Port Assignment  screen.
b. Select the corresponding equipment number in the  TVS No. menu.
c. Select your VPS model in the  Type menu.
KX-TVA50: Select  TVS200-1
KX-TVA200: Select  TVS300
Document Version  3.0  2010/06Installation Manual1174.5 KX-TD500 PBX Programming for DPT Integration  

d.Select the card (101: DLC/DHLC for jacks 1-8; 201: DLC/DHLC for jacks 9-12) which connects with
the VPS in the  VPS Card menu.
5.Assignment of the extension ports connected to the VPS
a. Continue programming in the  1-4 VPS (DPT) Port Assignment  screen.
b. Select the extension port number of the card (DLC/DHLC) to which the VPS (DPT) jack is to be
connected in the  Port No. menu. This program tells the KX-TD500 which extension ports are connected
to the VPS. This allows the KX-TD500 to send the proper...

f.Set  Status  to INS .
6. To set the trunk (CO line) features, follow the instructions for "Settings for the trunk (CO line) features" in
5.6  KX-TD500 PBX Programming for Inband Integration.
7. Set the PBX to send DID numbers to the VPS.
a. Go to the  2-7 System Option 6  screen.
b. Enable  67.Sending DID Number to VPS .
Document Version  3.0  2010/06Installation Manual1194.5 KX-TD500 PBX Programming for DPT Integration  

Note•This setting enables the PBX to send DID numbers to the VPS. If you want to use the features
which utilize DID numbers (e.g., Toll Saver, DID Call Routing), you must enable this setting.
8. Connect the jack assigned in Step 4 to the VPS.
9. Complete the PBX-VPS connection by following from step 1 of 4.7  Completing the PBX-VPS
Connection.
120Installation ManualDocument Version  3.0  2010/064.5 KX-TD500 PBX Programming for DPT Integration