Panasonic Kx Tva50 Installation Manual

4.6  KX-TA Series PBX Programming for APT
Integration For KX-TA824 programming via the Operating and Maintenance Tool, refer to 4.3  KX-TA824 PBX
Programming for APT Integration.
For KX-TA1232 programming, refer to 4.4  KX-TD Series PBX Programming for DPT Integration.
Programming procedures and availability may vary by PBX model, software version, etc. Refer to the
documentation included with the PBX or consult your dealer for more information.
Note
•The KX-TA824 can also be programmed via PC using the...

b.Press the  NEXT button (SP-PHONE).
Screen output:  Disable
c. Press the  SELECT button (AUTO ANS).
Screen output:  Port 7 or Port 15
d. To assign 2 jacks, press the  SELECT button (AUTO ANS) again.
Screen output:  Port 7 & 8 or Port 15 & 16
To assign 1 jack, skip this step.
e. Press the  STORE button.
f. Press  END (HOLD).
Note
•The lowest jack (jack 07 or jack 15) entered here must be connected to Port 1 of the VPS. To
change the current assignment from  Port 7 to Port 7 & 8 , you must first change it...

4.7  Completing the PBX-VPS ConnectionOnce you have finished installing all optional cards, connecting all telephones to the PBX, and configuring the
PBX for APT/DPT Integration, proceed with the following steps to complete and test the PBX-VPS connection.
1. Start KX-TVA Maintenance Console (see 3.2  KX-TVA Maintenance Console Installation).
2. Using KX-TVA Maintenance Console, initialize the PBX (see 8.1  Initializing the VPS).
3. Start the Quick Setup utility and proceed with Quick Setup (see 6.1.2...

Note•If the correct lines are not online, make sure the correct PBX type is selected, that the PBX is
properly programmed for APT/DPT Integration, and that the PBX and VPS are connected by
4-conductor cables.
7. To test the connection, dial the extension number of the VPS from a telephone connected to the PBX. If
the VPS answers, the APT/DPT connection has been established.
IMPORTANT
Important information for KX-TA users (except KX-TA1232):
When 2 VPSs are connected to a KX-TA series PBX, the following...

Section  5
PBX Programming for Inband Integration (KX-TVA50 only)
This section explains how to configure selected
Panasonic PBXs to use Inband Integration with the
VPS.Document Version  3.0  2010/06Installation Manual125 

5.1  Guidelines for Inband Integration
5.1.1  What is Inband Integration? In order for the VPS to function, it must be integrated with the PBX it serves. The type of integration that is
used determines how voice (caller messages, VPS prompts, etc.) and data (extension status, button presses,
etc.) are sent between the VPS and the PBX.
When the VPS and PBX use Inband Integration, voices are sent using analog technology, and data is sent
using analog DTMF tones.
The PBX informs the VPS of the status of...

Minimum Loop Current20 mAMinimum Line Voltage7 V DCMinimum Ringing Voltage40 V AC
DTMF SignalingFor system users to access VPS services and features, they must be able to send DTMF signals from their
telephones to the VPS port. As a general rule, most SLTs can send DTMF signals; however, many proprietary
telephones cannot. Some PBXs need to be programmed to make proprietary telephones use DTMF signaling.
TEST: Call an SLT extension from the telephone in question. When the
call is answered, see if the...

Follow-on ID or Called Party IDWhen forwarding or transferring a call to the VPS, a PBX with Follow-on ID sends the mailbox number of the
called subscriber to the VPS before connecting the caller. The VPS responds by playing that subscriber’s
personal greeting. This operation is sometimes called Call Forward to Mailbox. Without this feature, the VPS
cannot immediately play the called extension’ s greeting message when the line is busy or there is no answer
because the VPS does not know which mailbox to...

5.2  PBX Settings for Inband Integration
5.2.1  General Guidelines and Definitions In order for the VPS and PBX to communicate properly, certain settings of both the VPS and PBX should be
set to the same values.
Programming procedures and availability may vary by PBX model. Consult your dealer for more
information.
5.2.2  Global Parameters Global parameters are hardware settings that affect integration with the PBX. There is no need to change these
settings in a typical installation. Only change these...

5.2.3  PBX ParametersThe following items can be programmed using  KX-TVA Maintenance Console under System Parameters by
selecting the  Parameters tab.
PBX Environment •PBX Type
Specifies the type of PBX which is connected to the VPS.
• Integration Mode
Select  Inband . If PBX type is set to the Panasonic KX-T series, the inband signaling parameters are set
automatically and should not be altered.
SEQUENCE CODESDDisconnectFHookswitch FlashRRing DetectionTDial Tone DetectionXDial Extension,Dialing Pause...