Panasonic Kx Tva50 Installation Manual

c.Click  Apply  to save the changed data.
3.Set the amount of time before a call is considered to be unanswered and therefore forwarded to the VPS.
a. Go to the  System-Timers & Counters-CO / Extension  screen.
b. Assign the  Intercept Timer  parameter.
Document Version  3.0  2010/06Installation Manual1014.2 KX-TDE, KX-TDA, and KX-TAW Series PBX Programming for DPT Integration  

c.Click  Apply  to save the changed data.
4.Program the PBX so that it will direct intercepted calls to the VPS.
a. Go to the  Groups-VM(DPT) Group-System Setting  screen.
b. Set  Intercept to Mailbox  to Disable .
102Installation ManualDocument Version  3.0  2010/064.2 KX-TDE, KX-TDA, and KX-TAW Series PBX Programming for DPT Integration  

c.Click  Apply  to save the changed data.Document Version  3.0  2010/06Installation Manual1034.2 KX-TDE, KX-TDA, and KX-TAW Series PBX Programming for DPT Integration  

Example Settings (3)
Program the PBX to direct incoming trunk (CO line) calls to an Incoming Call Distribution (ICD) group, and to
then direct those calls to the VPS when they are not answered.
1. Program the PBX so that incoming trunk (CO line) calls are directed to an ICD group (DIL feature).
a. Go to the  CO & Incoming Call-DIL Table & Port Setting  screen.
b. Assign the  DIL Destination  for each time mode and trunk (CO line) to a specific extension number
(floating extension number of the ICD...

d.Click  Apply  to save the changed data.
3.Program the PBX so that it will direct overflowed calls to the ICD group’s mailbox.
a. Go to the  Groups-VM(DPT) Group-System Setting  screen.
b. Set  Intercept to Mailbox  to Enable .
Document Version  3.0  2010/06Installation Manual1054.2 KX-TDE, KX-TDA, and KX-TAW Series PBX Programming for DPT Integration  

c.Click  Apply  to save the changed data.
4.2.1  Installing Prompt Data for the VM Menu Feature
KX-TDA series PBXs (MPR version 2.0 or higher) and KX-TDE series PBXs can use the VM Menu feature,
however, VM Menu prompt data must first be installed in the PBX using the following procedure.
1. Shutdown the PBX, eject the SD memory card, and insert the SD memory card into your PC.
2. Insert the CD-ROM included with the VPS into your PC’s CD-ROM drive.
3. Find the following folder:  CD-ROM...

4.3  KX-TA824 PBX Programming for APT IntegrationThe instructions in this section are for programming a KX-TA824 via the Operating and Maintenance Tool. To
program a KX-TA824 using the Manager Extension, follow the instructions for KX-TA series PBX programming
by referring to 4.6  KX-TA Series PBX Programming for APT Integration.
Note
•Software version 3.0 or higher is required for 4-port APT Integration. Consult your dealer for more
information.
1. Go to the  1.System - 1.Date  & Time  screen. Set the...

automatically. Also the Extension Hunting type is set as Circular automatically in each of these 2 extension
groups. You can confirm these automatic settings in the  2.Extension - 6.Extension Group screen.
3.Program the appropriate trunk (CO line) feature settings depending on how your customer plans to use
the VPS: a) to answer all incoming calls, b) as an operator backup, or c) to only answer calls not answered
by user extensions.
a. If the VPS is answering all calls:
Go to the  3.CO - 1.Line Mode...

DIL to the first port of the hunt group. Lines programmed as Normal do not hunt. Click  Apply to save
the changed data.
b. If the VPS is only answering calls not answered by the operator (Operator Backup):
Go to the  3.CO - 2.Incoming / Outgoing  screen. Program lines to ring operator extensions immediately
for all time modes. To give the operator time to answer the call before the VPS picks up, we recommend
setting the delay to a few seconds for each extension connected to the VPS. Set a different delay...

c.If the VPS is only answering calls not answered by user extensions:
Go to the  3.CO - 2.Incoming / Outgoing  screen. Program lines to ring user extensions immediately
for all time modes. To give users time to answer the call before the VPS picks up, we recommend
setting the delay to a few seconds for each extension connected to the VPS. Set a different delay time
for each extension connected to the VPS. Finally, go to the  3.CO - 1.Line Mode screen and set all
trunk (CO line) types to  Normal. Click...