Panasonic DLP Projector PT-DZ21K2 PT-DS20K2 PT-DW17K2 PT-DZ16K2 Operating Instructions

Chapter 4 Settings — [DISPLAY OPTION] menu
ENGLISH - 121
Setting [WARNING MESSAGE]
Set the display/hide of the warning message.
1) 
Press 
 as to select [ON-SCREEN DISPLAY].
2)
 
Press the  button.
 fThe 

[ON-SCREEN DISPLAY] screen is displayed.
3)
 
Press 
 as to select [WARNING MESSAGE].
4)
 
Press 
 qw to switch the item.
 fThe items will switch each time you press the button.
[ON] Displays the warning message.
[OFF] Hides the warning message.
[IMAGE ROTATION]
(Only for PT-DZ21K2, PT- DS20K2, PT-...

Chapter 4 Settings — [DISPLAY OPTION] menu
122 - ENGLISH
Note
 fThe startup logo will disappear in approximately 15 seconds. fT
o create/register the [USER LOGO] image, use “Logo Transfer Software” included in the supplied CD-ROM.
[UNIFORMITY]
Correct the brightness and color unevenness of the entire screen.
Setting each color
1) Press  as to select [UNIFORMITY].
2)  
Press the  button.
 fThe 

[UNIFORMITY] screen is displayed.
3)
 
Press 
 as to select [WHITE], [RED], [GREEN], or [BLUE].
4)
 
Press 
 qw...

Chapter 4 Settings — [DISPLAY OPTION] menu
ENGLISH - 123
2) Press the  button.
 fThe 

[SHUTTER SETTING]  screen is displayed.
3)
 
Press 
 as to select [FADE-IN] or [FADE-OUT].
4)
 
Press 
 qw to switch the item.
Item Adjustment
[FADE-IN]
[FADE-OUT] [OFF]
Does not set fade-in or fade-out.
[0.5s] - [10.0s] Sets the fade-in or fade-out time.
Select an item from [0.5s] to [4.0s], [5.0s], [7.0s], and [10.0s]. 
Items from [0.5s] to [4.0s] can be selected in increments of 0.5.
Note
 f
Press the  button on the...

Chapter 4 Settings — [DISPLAY OPTION] menu
124 - ENGLISH
[OFF]Does not display the waveform monitor.
[ON] Displays the waveform monitor.
3) Press the  button two times to clear .
4)  
Press 
 as to select any horizontal line.
5)
 
Press the  button to switch the Select line to either luminance, red, green, or blue.
 fLine selection items switch each time the  is pressed only when the waveform monitor is 
displayed.
“Select line (luminance)” Displayed in white waveform.
“Select line (red)” Displayed in...

Chapter 4 Settings — [DISPLAY OPTION] menu
ENGLISH - 125
Note
 fFor DVI - D signal, HDMI signal, SDI signal, and DIGITAL LINK signal, confirm that the [SIGNAL LEVEL] setting is correct before black level 
adjustment. (SDI signal is supported only for PT- DZ21K2, PT- DS20K2, PT- DZ16K2)
[CUT OFF]
Each red, green, and blue color component can be removed.
1)
 
Press 
 as to select [CUT OFF].
2)
 
Press the  button.
 fThe 

[CUT OFF] screen is displayed.
3)
 
Press 
 as to select [RED], [GREEN], or [BLUE]....

Chapter 4 Settings — [PROJECTOR SETUP] menu
126 - ENGLISH
[PROJECTOR SETUP] menu
On the menu screen, select [PROJECTOR SETUP] from the main menu, and select an item from the sub-
menu.
Refer to “Navigating through the menu” (x
  page   77) for the operation of the menu screen.
[PROJECTOR ID]
The projector has an ID number setting function that can be used when mu\
ltiple projectors are used side by side 
to enable simultaneous control or individual control via a single remote\
 control.
1)
 
Press 
 as...

Chapter 4 Settings — [PROJECTOR SETUP] menu
ENGLISH - 127
[QUAD]Four lamps will light.
3) Press the  button.
Note
 f For a certain period of time after [LAMP  SELECT] is switched, [LAMP SELECT] cannot be switched again, because the speed of the lamp 
replacement cycle will increase. Repeatedly switching [LAMP SELECT] in a short time will also increase the speed of the lamp replacement 
cycle.
 f The colors of the items indicate the status.
Green Current setting
Yellow Current setting (when there is a...

Chapter 4 Settings — [PROJECTOR SETUP] menu
128 - ENGLISH
Note
 fThe [LAMP  RELAY] function is enabled when [SINGLE], [DUAL], [TRIPLE], or [QUAD] is selected in [LAMP SELECT]. fWhen [SINGLE] or [DUAL] is selected in [LAMP
 SELECT], lamps are switched at the specified time. When [TRIPLE] is selected in [LAMP  
SELECT], lamps are switched three times every two hours after the specified time, and then the previous status is maintained until the next 
specified time.
When [QUAD] is selected in [LAMP SELECT],...

Chapter 4 Settings — [PROJECTOR SETUP] menu
ENGLISH - 129
[AUTO]Corrects the brightness of the screen by the brightness sensor.
Automatically corrects screen brightness when lamp brightness changes.
[PC] Synchronizes nine or more projectors using a computer and dedicated software “Multi Monitoring & 
Control Software”
*1.
*1 “Multi Monitoring & Control Software” is included in the supplied CD-ROM.
 f
When [PC] is selected, proceed to Step  11 ).
7)
 
Press 
 as to select [LINK].
8)
 
Press 
 qw to switch...

Chapter 4 Settings — [PROJECTOR SETUP] menu
130 - ENGLISH
 fIf the  button is pressed when [LINK] is set from [GROUP  A] to [GROUP D], the group name is 
displayed on the screens of projectors that have been set in the same gr\
oup.
LINK GROUP A
Note
 fWhen [MODE] in [BRIGHTNESS CONTROL  SETUP] is set to [AUTO] or [PC], keep the shutter function disabled (shutter: open) for at least 
two minutes to perform the brightness sensor calibration after the [BRIGHTNESS CONTROL  SETUP] setting has been...