Panasonic DLP Projector PT-DZ21K2 PT-DS20K2 PT-DW17K2 PT-DZ16K2 Operating Instructions

Chapter 3 Basic Operations — Operating with the remote control
ENGLISH - 71
Operating with the remote control
Switching the input
The input for projection can be switched. Method to switch the input is as follows.
 fPress the input selection button and directly specify the input to proje\
ct.
 fDisplay the input selection screen and select the input to project from \
the list.
 button
Switching the input directly
The input for projection can be switched by directly specifying it.
1)
 
Press the input...

Chapter 3 Basic Operations — Operating with the remote control
72 - ENGLISH
*1
(PT-DZ21K2, PT- DS20K2)
Switches the input to SDI1 or SDI2. Switches to the other input when one\
 input has already been 
selected. Also, input selection can be fixed to SDI1 or SDI2 using the [SECURITY] menu  → 
[CONTROL DEVICE SETUP].
(PT
-

DZ16K2)
Switches the input to SDI.
*1 SDI input is supported only for PT- DZ21K2, PT- DS20K2, and PT- DZ16K2.
Note
 fWhen the optional DIGIT AL LINK output supported device (Model No.:...

Chapter 3 Basic Operations — Operating with the remote control
ENGLISH - 73
2) Press the  button again.
 fThe image is displayed.
Note
 f The power indicator  will blink slowly in green while the shutter function is in use (shutter: closed). fY
ou can set the speed of shutter opening/closing via the [DISPLAY OPTION] menu  → [SHUTTER SETTING].
Using the on-screen display function
Turn off the on-screen display function (no display) when you do not wish the viewers to see the on-screen 
display, such as...

Chapter 3 Basic Operations — Operating with the remote control
74 - ENGLISH
Note
 fRefer to the [POSITION] menu  →  [ASPECT] (x   page   91) for details.
Using the function button
The  button of the remote control can be used as a simplified shortcut button by assigning the 
following functions: [P IN P], [SUB MEMORY], [SYSTEM SELECTOR], [SYSTEM DAYLIGHT VIEW], [FREEZE], 
[WAVEFORM MONITOR], [LENS MEMORY LOAD], [LEFT/RIGHT SWAP], [PROJECTION METHOD]
 button
1) Press the  button.
Note
 f [LEFT/RIGHT...

Chapter 3 Basic Operations — Operating with the remote control
ENGLISH - 75
Using the AC voltage monitor function
The value of input supply voltage can be displayed on the self-diagnosis\
 display at the side of the projector.
 rTo display during projection
1) Press the power on < b > button.
 fThe value of the input supply voltage is displayed only as numeric value\
 on the self-diagnosis display

.
 fThe display will turn of

f automatically after approximately 3 seconds.
 rTo display during standby...

76 - ENGLISH
Chapter 4 Settings
This chapter describes the settings and adjustments you can make using t\
he on-screen menu.  

Chapter 4 Settings — Menu navigation
ENGLISH - 77
Menu navigation
The on-screen menu (Menu) is used to perform various settings and adjustments of the projector.
Navigating through the menu
Operating procedure
 button
1) Press the  button on the remote control or control panel.
 fThe 

[MAIN MENU] screen is displayed.
MAIN MENUPICTURE
POSITION
ADVANCED MENU
DISPLAY LANGUAGE
DISPLAY OPTION 3D SETTINGS
PROJECTOR SETUP
TEST PATTERN
SIGNAL LIST
SECURITY
NETWORK
MENU SELECT
SUB MENU
P IN P
ENTER
2) Press  as...

Chapter 4 Settings — Menu navigation
78 - ENGLISH
4) Press as to select a sub-menu, and press qw or the  button to change or adjust settings.
 fSome items will switch in order as follows each time you press  qw

.
ABC
 fFor some items, press  qw to display an individual adjustment screen with a bar scale as shown be\
low.
0CONTRAST
ADJUST
Note
 fPressing the  button while the menu screen is displayed returns to the previous menu. fDepending on the signals to be input to the projector
, some items or...

Chapter 4 Settings — Menu navigation
ENGLISH - 79
Main menu itemPage
[3D SETTINGS]*1103
[DISPLAY OPTION] 108
[PROJECTOR SETUP]126
[P IN P]144
[TEST PATTERN]146
[SIGNAL LIST]147
[SECURITY]150
[NETWORK]154
*1 Only for PT-DZ21K2, PT- DS20K2
Sub-menu
The sub-menu of the selected main menu item is displayed, and you can se\
t and adjust items in the sub-menu.
[PICTURE] 
Sub-menu item Factory defaultPage
[PICTURE MODE] [STANDARD]
*183
[CONTRAST] [0]
*283
[BRIGHTNESS] [0]
*284
[COLOR] [2]
*284
[TINT] [-2]
*284...

Chapter 4 Settings — Menu navigation
80 - ENGLISH
Sub-menu itemFactory defaultPage
[CLAMP POSITION] [24]
*197
[EDGE BLENDING] [OFF]98
[FRAME RESPONSE] [NORMAL]99
[FRAME CREATION] [2]100
[FRAME LOCK]
*2― 100
[RASTER POSITION] ―101
*1 Depends on the signal input.
*2  Only for PT- DZ21K2, PT- DS20K2
Note
 fSub-menu items and factory default settings vary depending on the select\
ed input terminal.
[DISPLAY LANGUAGE] 
Details (x page 102)
[3D SETTINGS] 
(Only for PT- DZ21K2, PT- DS20K2)
Sub-menu item Factory...