Panasonic DBS 576HD Technical Manual

							Section 700 - Operation Chapter 7. SLT Features
576-50-700 DBS 576HD (USA) issued September 2001 5-79
• Storing a new number erases any previously stored data.
• If the called party’s number and name are stored in the PSD code, that information appears on the 
display when you use the speed dial code.
• Speed dial numbers can contain up to 24 characters. The following table reflects which keys to 
use.
* Indicates that the digits that follow are either a feature access code or an extension 
number. (Not needed if your System is set for Intercom Level.) See Note below.
** Indicates that the digits that follow are for an outside number and the System should 
seize the next available trunk when dialing. (Not needed if your System is set for CO 
Level.) See Note below.
*** Indicates that the enclosed digits should not be displayed during dialing. Must precede 
and follow the digits that you do not want displayed. Example: AUTO *2 555-4143 
AUTO *2.
Note:The System has two levels - CO Level and Intercom Level. If set at CO Level (default), 
you must enter the code for Intercom Level when programming a feature access code or 
extension number for speed dialing. If the System is set at Intercom Level, you must enter the 
MCO Code when programming an outside number for speed dialing.
System Speed Dial
You can store frequently called numbers using the SSD feature. Either 80 or 800 SSD numbers can be 
programmed, depending on how the System is configured. In an 80 SSD-number system, the SSD 
numbers are stored in bins 00-79. In 800 SSD-number systems, the SSD numbers are stored in bins 
000-799. 
Operation
To assign SSD numbers:To indicate. . . Enter/Press Shown on Display?
Digit or character0, 1 - 9, *, #yes (unless preceded by AUTO * 2 - see *** 
below)
Intercom Level *AUTO * #no
MCO Code **AUTO * 0no
PauseREDIALno
DP - DTMF CodeAUTO * *no
SSD CodeAUTO 
NN(N)no
Hyphen (-)PROGyes 
Display Number (Start / Stop) ***AUTO * 2
DTMF Conversion After the 
Other Party AnswersAUTO * 3 
Action Result
1.   Lift the handset or press the ON/OFF key. Intercom dial tone 
						

							5-80 DBS 576HD (USA) issued September 2001 576-50-700
Chapter 7. SLT Features Section 700 - Operation
To dial an SSD number by entering the speed dial bin number:
To check an SSD number:Action Result
2.   (A) Press the PROG key.
(B) Press the AUTO key.
OR...
(A) Enter the Speed Dial Set/Clear code (default = 710).
3.   Enter the SSD bin number (00-79 or 000-799).Enter Spd Dial displays
4.   Dial the phone number.
5.   Press the HOLD key.Stored Spd Dial displays
6.   Replace the handset or press the ON/OFF key.
Action Result
1.   Lift the handset or press the ON/OFF key. Intercom dial tone
2.   If necessary, access an outside line. Outside dial tone
3.   Press the AUTO key.
OR...
Enter the Speed Dial Originate code (default = 80).A displays
4.   Enter the SSD bin number (00-79 or 000-799).
5.   Complete the call and replace the handset or press the ON/
OFF key.
Action Result
1.   Lift the handset or press the ON/OFF key. Intercom dial tone
2.   Press the CONF key.C displays
3.   Press the AUTO key.
4.   Enter the SSD bin number (00-79 or 000-799). Programmed data displays 
5.   If you want to check the next SSD number, press the HOLD 
key.
6.   Replace the handset or press the ON/OFF key. 
						

							Section 700 - Operation Chapter 7. SLT Features
576-50-700 DBS 576HD (USA) issued September 2001 5-81
To delete an SSD number:
Hardware Requirements
•N/A
Related Programming
• FF1-0-15, 16, & 17: SSD Blocks
• FF1-0-02: SSD Digits
• FF1-0-03: Extension COS (SSD Assignment)
• FF8-1-02: SSD Number
• FF8-1-02: SSD Name
Considerations
• If numbers do not appear on the display when you use SSD codes (00-79 or 000-799), your 
extension is not programmed to display that data.
• The System can be programmed to allow SSD numbers to override toll restrictions. 
Speed Dial Linking
You can automatically link together up to 6 SSD numbers in 1 PSD bin to handle telephone numbers 
longer than 24 characters. You can then dial the entire number by pressing the programmed PSD key 
or by entering the speed dial bin number.
Alternatively, any combination of PSDs and SSDs can be manually linked together by pressing the 
keys in the desired sequence. This can be useful for prepending account codes or long distance carrier 
access codes, etc.
Note:Before linking multiple SSD numbers to a PSD bin, the SSD bins must already have been 
programmed with the appropriate speed dial information.Action Result
1.   Lift the handset or press the ON/OFF key. Intercom dial tone
2.   (A) Press the PROG key.
(B) Press the AUTO key.
OR...
(A) Enter the Speed Dial Set/Clear code (default = 710).
3.   Enter the SSD bin number (00-79 or 000-799).
4.   Press the HOLD key.Cleared Spd Dial displays
5.   Replace the handset or press the ON/OFF key. 
						

							5-82 DBS 576HD (USA) issued September 2001 576-50-700
Chapter 7. SLT Features Section 700 - Operation
Operation
To link multiple SSD numbers to a PSD bin:
To use a PSD Key that links multiple SSDs:
To manually link speed dial keys together:
Hardware Requirements
•N/AAction Result
1.   Determine the SSD bin numbers to be linked
2.   Lift the handset or press the ON/OFF key.
3.   (A) Press the PROG key.
(B) Press the AUTO key.
OR...
(A) Enter the Speed Dial Set/Clear code (default = 710).
4.   Enter the PSD bin number (80-90).Enter Spd Dial displays
5.   Press the AUTO key.
6.   Enter the SSD bin number (00-79 or 000-799) that contains 
the first part of the number to be dialed.
7.   Repeat steps 5-6 up to 5 more times for all additional SSDs 
to be dialed.
8.   Press the HOLD key when finished.Stored PSDXXX displays
Action Result
1.   If necessary, select the trunk group (9, 81-84). (Normally 
the trunk is selected by the speed dial numbers.)
2.   Press the PSD key.
Action Result
1.   Lift the handset or press the ON/OFF key. Intercom dial tone
2.   If necessary, access an outside line.
3.   If you are using a PSD number, press the one-touch key for 
the first part of the number.
If you are using an SSD number, press the AUTO key, then 
enter the SSD bin number.
4.   Use the one-touch keys or press the AUTO key and enter 
the SSD codes to dial the parts of the phone number until it 
is completed. 
						

							Section 700 - Operation Chapter 7. SLT Features
576-50-700 DBS 576HD (USA) issued September 2001 5-83
Related Programming
•N/A
Considerations
•N/A
Speed Dial Name Assignments
You can assign names to PSD numbers from a key telephone without entering the programming 
mode. If allowed in the Extension Class of Service (COS), you can also assign names to SSD 
numbers.
(PSD names can contain a maximum of 7 characters. SSD names can contain a maximum of 16 
characters.)
Operation
PSD Names:
To set PSD names using a large-display or small-display phone:
Action Result
1.   Lift the handset or press the ON/OFF key.
2.   Press the PROG key.
3.   Press the * key.
4.   Enter 0 for the PSD Name Assignment mode.A B C D E F P80 displays (where P80 = 
PSD bin 80)
5.   Press the VOLUME up or down arrow key to display the 
desired PSD bin number.A B C D E F PXX displays (where PXX 
= desired PSD bin number)
6.   Enter the extension name:
•   If using a large-display phone, press the soft key next 
to the desired row of letters. (See Example 1 on page 
5-84.)
•   If using a small-display phone press the appropriate 
one-touch key. (See Example 2 on page 5-86.)
Note: Press the FLASH key to clear any existing data
7.   Use the bottom row of FF keys to select a single letter. 
•   See “Example 1. Large-display phone” on page 5-84.
•   See “Example 2. Small-display phone” on page 5-86.
Notes:
•   Press the * key to erase a single entry.
•   Press the # key to enter a space.
8.   Repeat steps 6-7 as many times as necessary to enter the 
desired PSD name.
Note: Press the FLASH key to clear the entire entry.
9.   Press the HOLD key when finished. Next PSD bin number displays
10.   To enter another speed dial name repeat steps 5-9. 
						

							5-84 DBS 576HD (USA) issued September 2001 576-50-700
Chapter 7. SLT Features Section 700 - Operation
SSD Names:
To set SSD names using a large-display or small-display phone:
Example 1. Large-display phone
To  e n t e r  D:
a.  Press the first soft key on the top left.
Action Result
1.   Lift the handset or press the ON/OFF key.
2.   Press the PROG key.
3.   Press the * key.
4.   Enter 1 for the SSD Name Assignment mode.SSD NO.=>
SSD NAME displays
5.   Enter the speed dial bin number (00-79 or 000-799).
6.   Press the HOLD key.-SSDXXX 
A B C D E F XXX displays (where XXX 
= specified SSD bin number)
7.   Press the FLASH key to clear the current data.A B C D E F XXX displays (where XXX 
= specified SSD bin number)
8.   Enter the speed dial name:
•   If using a large-display phone, press the soft key next 
to the desired row of letters. (See Example 1 on page 
5-84.)
•   If using a small-display phone press the appropriate 
one-touch key. (See Example 2 on page 5-86.)
9.   Use the bottom row of FF keys to select a single letter. 
•   See “Example 1. Large-display phone” on page 5-84.
•   See “Example 2. Small-display phone” on page 5-86.
Notes:
•   Press the * key to erase a single entry.
•   Press the # key to enter a space.
10.   Repeat steps 8-9 as many times as necessary to enter the 
desired SSD name.
Note: Press the FLASH key to clear the entire entry.
11.   Press the HOLD key when finished. Next SSD bin number displays
12.   To enter another speed dial name, press the CONF key and 
repeat steps 5-11.SSD NO.=>
SSD NAME displays 
						

							Section 700 - Operation Chapter 7. SLT Features
576-50-700 DBS 576HD (USA) issued September 2001 5-85
b.  Press the fourth FF key from the left on the bottom row.
To  e n t e r  o:
a.  Press the third soft key from the top right.
b.  Press the third FF key from the left on the bottom row. 
						

							5-86 DBS 576HD (USA) issued September 2001 576-50-700
Chapter 7. SLT Features Section 700 - Operation
Example 2. Small-display phone
Refer to the following diagram to determine which one-touch key to press. (See step 7-8 above.)
To  e n t e r  D:
a.  Press the first one-touch key from the left on the bottom row.
b.  Press the fourth FF key from the left on the bottom row.
G H I J K L M N O P Q R S T U V W X A B C D E F Y Z . , ’ -
a b c d e fg h i j k lm n o p q rs t u v w xy z : & / sp
END MODE 
						

							Section 700 - Operation Chapter 7. SLT Features
576-50-700 DBS 576HD (USA) issued September 2001 5-87
To  e n t e r  o:
a.  Press the third one-touch key from the left on the top row.
b.  Press the third FF key from the left on the bottom row.
Hardware Requirements
•N/A
Related Programming
• FF1-0-03: Extension COS (User Log-in)
• FF3: Extension COS
• FF8-1: SSD & PSD
Considerations
• The ability to assign SSD names is allowed/restricted to anyone with a COS that allows access to 
User Maintenance features. (See Chapter 4 “User Maintenance” of this document.)
Station Lockout
Description
Use the Station Lockout feature to limit use of your phone by others when you are away from your 
telephone. When the Station Lockout feature is in use, the TRS Class of your telephone is changed. 
Anyone using your telephone is limited to the calling abilities defined by this Lockout TRS Class.
In addition, with the appropriate COS, you can set or cancel Station Lockout for other telephones.
END MODE
PROG
CONF 
						

							5-88 DBS 576HD (USA) issued September 2001 576-50-700
Chapter 7. SLT Features Section 700 - Operation
Operation
To activate Station Lockout feature:
To cancel Station Lockout feature:
To activate Station Lockout feature for another extension:
To cancel Station Lockout feature for another extension:Action Result
1.   Lift the handset or press the ON/OFF key. Intercom dial tone
2.   Enter the Station Lockout feature code (default = 746).St. Lock Set displays
3.   Replace the handset or press the ON/OFF key.Lock displays
Action Result
1.   Lift the handset or press the ON/OFF key. Intercom dial tone
2.   Enter the Station Lockout feature code (default = 746) .Enter ID Code displays
3.   Enter the Walking TRS/Station Lockout security code. Cleared St. Lock displays
4.   Replace the handset or press the ON/OFF key. The telephone display returns to the nor-
mal display.
Action Result
1.   Lift the handset or press the ON/OFF key. Intercom dial tone
2.   Enter the Station Lockout for another extension feature code 
(default = 747).Enter Lock EXT # displays
3.   Dial the extension number to activate station lockout.St. Lock Set displays
4.   Replace the handset or press the ON/OFF key.
Action Result
1.   Lift the handset or press the ON/OFF key. Intercom dial tone
2.   Enter the Station Lockout feature code (default = 748).Enter Lock EXT #displays
3.   Enter the extension number to activate station lockout.Enter ID Code displays
4.   Enter the Walking TRS/Station Lockout security code. Cleared St. Lock displays
5.   Replace the handset or press the ON/OFF key. The telephone display returns to the nor-
mal display.