Panasonic DBS 576HD Technical Manual

							Section 700 - Operation Chapter 7. SLT Features
576-50-700 DBS 576HD (USA) issued September 2001 3-33
Related Programming
•N/A
Considerations
•N/A
Free Slot
Description
The DBS 576HD cabinet contains 5 free slots. These slots can be used for trunk cards, extension 
cards, or certain option cards. 
Some circuit cards such as the Integrated Services Digital Network (ISDN) - Primary Rate Interface 
(PRI) card occupy more that one slot.
Hardware Requirements
•N/A
Related Programming
•N/A
Considerations
•N/A
Hunting Groups
Description
Hunting allows calls to be automatically transferred among a preselected group of phones. If a phone 
is busy or there is no answer in a set amount of time, the call will hunt to the next phone in the hunt 
group.
A phone assigned to a hunt group is called a member. Up to 20 members can be assigned to a hunt 
group. Up to 12 hunt groups are available per cabinet.
Several methods of station hunting are available. Some methods require use of a pilot number (a 
fictitious extension number) while others start by a direct call to a hunt group member. 
The System supports the following hunting groups:
• Pilot Terminal Hunt Group
• Pilot Distributed Hunt Group
• Switch Back Hunt Group
• Circular Hunt Group
• Next Extension/Hunt Group 
						

							3-34 DBS 576HD (USA) issued September 2001 576-50-700
Chapter 7. SLT Features Section 700 - Operation
Pilot Terminal Hunt Group
Pilot Terminal Hunt Group directs calls to a pilot number. The System begins with the first member 
and hunts through the group for the first available member to receive the call. If no member is 
available (extension is busy or there is no answer for a specified amount of time), the call is queued 
for the first member to become available. You can also set the Queuing Timer to specify how long the 
System will search the initial hunt group before beginning to search the next hunt group or extension.
The main advantage of this type of hunting is that the same hunting order is taken for all calls. This is 
useful in presenting calls to selected members first.
Pilot Distributed Hunt Group
Pilot Distributed Hunt Group directs calls to a pilot number. The System reviews who received the 
last call and begins hunting with the next member. If the last member in the group is reached and no 
member is available, the hunt continues with the first member and proceeds forward. After a complete 
search and no available member is found (extension is busy or there is no answer for a specified 
amount of time), the call is queued for the first member to become available. You can also set the 
Queuing Timer and specify how the long the System will search the initial hunt group before 
beginning to search the next hunt group or extension.
The main advantage of this type of hunting is that calls are evenly distributed throughout the group.
Switch Back Hunt Group
Switch Back Hunt Group initiates hunting in a specified group for calls made to a member extension 
in the group. If the called member of the hunt group is busy, the System begins hunting forward to the 
end of the group. If no member is available, the system hunts backward
 from the called member. If no 
member is available (extension is busy or there is no answer for a specified amount of time), the call 
is queued for the first member to become available. You can also set the Queuing Timer and specify 
how the long the System will search the initial hunt group before beginning to search the next hunt 
group or extension. 
The main advantage of this type of hunting is that calls can be directed to start with a selected portion 
of the hunting group based on the directed number. However, all members are eventually searched.
Circular Hunt Group
Circular Hunt Group initiates hunting in a specified group for calls made to a member extension in the 
group. If the called member of the hunt group is busy, the System begins hunting forward to the end of 
the group and then moves forward
 from the first member of the group. If no member is available 
(extension is busy or there is no answer for a specified amount of time), the call is queued for the first 
member to become available. You can also set the Queuing Timer and specify how the long the 
System will search the initial hunt group before beginning to search the next hunt group or extension. 
The main advantage of this type of hunting is that calls can be directed to start with a selected portion 
of the hunting group based on the directed number. However, all members are eventually searched.
Next Extension/Hunt Group
Next Extension/Hunt Group lets you specify which extension or hunt group to search after the 
Queuing Timer expires. This hunt group can be set as any type of hunt group, an attendant group, or 
an extension (including virtual extensions).
Hardware Requirements
•N/A 
						

							Section 700 - Operation Chapter 7. SLT Features
576-50-700 DBS 576HD (USA) issued September 2001 3-35
Related Programming
• FF5-1: Hunt Groups Mode
• FF5-1: Pilot Number
• FF5-1: Member
• FF5-1: Delayed Hunt Timer
• FF5-1: Queuing Timer
• FF5-1: Next Hunting
Considerations
• If a member of the hunt group has Do-Not-Disturb (DND) or Call Forwarding - All set, that 
phone is temporarily removed from the hunt group.
• If a member of the hunt group has Call Forwarding - Busy set and the extension is busy, the call 
goes to the next phone in the hunt group.
• If all members are busy for the duration of the busy queuing timer, the call can be forwarded to 
another hunt group or another extension.
• A hunt group can contain both real extensions and virtual extensions. If virtual, several phones 
can be made to ring at the same time.
• The pilot number for a hunt group is flexible (i.e., any extension number can be designated as the 
pilot [not a real extension]).
• Hunt groups support the following call types:
•   Direct Inward Dialing (DID) / Dialed Number Identification Service (DNIS) / Direct 
Dial Inward (DDI)
•   Direct Inward System Access (DISA)
•   Extension calls
•   Private network attendant calls
•   Call forward incoming
•   Call forwarded to Attendant Hunt Group
• For Version 3.5 and higher, a queuing wait timer allows you to queue calls in a Hunt Group for a 
fixed period of time. When the call has passed through the Hunt Group once, the timer is 
activated and the call is re-routed to the top of the group. The system continues to hunt for an 
available agent until the timer limit expires, and the call is diverted to another location.
Internal Hold Tone
Description
If a Music-on-Hold (MOH) sound source is unavailable, a periodic hold tone generated internally in 
the System can be provided to a caller. For more information, see “Music-on-Hold” on page 3-37.
Hardware Requirements
•N/A
Related Programming
• FF1: MOH Assignment 
						

							3-36 DBS 576HD (USA) issued September 2001 576-50-700
Chapter 7. SLT Features Section 700 - Operation
Considerations
•N/A
LAN TAPI
Description
LAN TAPI opens a line of communications between the DBS 576HD’s switching systems and a PC. 
This is accomplished through the use of a Telephony Server connected to a LAN. Users on PCs can 
use specific applications to send and receive information to and from the DBS 576HD via the LAN. 
Using a software program called the Telephony Service Provider (TSP), call control information 
(TAPI commands) is translated into commands that can be interpreted by the DBS 576HD. This 
“open” communication between the PC and the telephone system allows the user to initiate and 
handle calls via the application running on the PC.
Hardware Requirements
• Windows NT network
• Telephony Server connected to the network
• Panasonic TSP software installed on the Telephony Server
• PC (Windows 95/98 or NT operating system)
• Supported TAPI application
Related Programming
•See Section 575 - LAN TAPI Installation
Considerations
•N/A
MCO Tenant Group
Description
When the System is configured for tenant operation, MCO Tenant Group determines which trunks 
groups are used for incoming and outgoing calls. 
Each MCO trunk group is assigned to an MCO tenant group for incoming calls and for outgoing calls. 
By default, Trunk Group 1 is assigned to MCO Tenant Group 1, Trunk Group 2 is assigned to MCO 
Tenant Group 2, etc. for both incoming and outgoing calls. 
For outgoing calls, each tenant group has 5 auto-trunk selections available. By default the first auto-
trunk selection is seized by entering 9, the second by entering 81, etc.
The number of MCO tenant groups available depends on the number of ports in the system as follows:
• DBS 576HD: 
•   96-port system: 1 to 12 MCO tenant groups 
						

							Section 700 - Operation Chapter 7. SLT Features
576-50-700 DBS 576HD (USA) issued September 2001 3-37
Hardware Requirements
•N/A
Related Programming
• FF1-3: MCO Incoming/Outgoing
• FF5-2: MCO Outgoing Trunk Assignments
• FF5-3: MCO Incoming Trunk Assignments
• FF2: Trunk Tenant Group Assignments
• FF3: Extension Tenant Group Assignments
Considerations
• When you first assign a trunk to a Trunk Tenant Group from the initial setting of (0), the system 
automatically assigns the trunks as a member of the same number MCO Trunk Group (FF5-2 and 
FF5-3). For instance, if Trunk 10 is assigned as a member of Trunk Tenant Group 1, then Trunk 
10 is automatically assigned as a member of MCO Outbound Trunk Group 1 and MCO Inbound 
Trunk Group 1. These assignments can be manually changed if desired.
Music-on-Hold
Description
The System can provide Music-on-Hold (MOH) to parties on hold (either CO line, extension, or 
network party). The MOH feature can also be used to play announcements or advertisements if 
desired. 
Hardware Requirements
• The music source must be purchased separately. It is not provided with the System.
Related Programming
•N/A
Considerations
•
Name Assignments
Description
Names may be assigned to the following:Important:
 A license may be required from the American Society of Compos-
ers, Authors, and Publishers (ASCAP) or similar organizations to transmit radio 
or recorded music through the MOH feature.  Panasonic Telecommunication 
Systems Company, its distributors, and affiliates assume no liability should users 
of Panasonic equipment fail to obtain such a license.  
						

							3-38 DBS 576HD (USA) issued September 2001 576-50-700
Chapter 7. SLT Features Section 700 - Operation
• Extensions
• Trunks
• Direct Inward Dials (DIDs)
• Personal Speed Dials (PSDs)
• Systems Speed Dials (SSDs)
Trunks names and DID names must be assigned in dealer programming mode. Extension names and 
Speed Dial names may be assigned from a display telephone.
This feature does not require the use of a DSS/72 console or entering the programming mode.
Extension Name Assignments
Extension names can be up to 10 characters in length. (Assignment of extension names must be 
allowed in the Extension Class of Service [COS].)
Operation
To set extension names using a large-display or small-display phone:
Action Result
1.   Lift the handset or press the ON/OFF key. Intercom dial tone
2.   Press the PROG key.
3.   Press the * key.
4.   Enter 2 for the Extension Name Assignment mode.EXT NO.=>
EXT NAME
 displays
5.   Enter the extension number.
6.   Press the HOLD key.XXX
A B C D E F XXX
 displays (where 
XXX = extension number)
7.   Press the FLASH key to clear the existing data.
A B C D E F XXX displays (where 
XXX = extension number)
8.   Enter the extension name:
•   If using a large-display phone, press the soft key next 
to the desired row of letters. (See Example 1 on page 
3-39.)
•   If using a small-display phone press the appropriate 
one-touch key. (See Example 2 on page 3-40.)
9.   Use the bottom row of FF keys to select a single letter. 
•   See “Example 1. Large-Display Phone” on page 3-39.
•   See “Example 2. Small-Display Phone” on page 3-40.
Notes:
•   Press the * key to erase a single entry.
•   Press the # key to enter a space. 
						

							Section 700 - Operation Chapter 7. SLT Features
576-50-700 DBS 576HD (USA) issued September 2001 3-39
Example 1. Large-Display Phone
To  e n t e r  D:
a.  Press the first soft key on the top left.
b.  Press the fourth FF key from the left on the bottom row.
To  e n t e r  o:
a.  Press the third soft key from the top right.
10.   Repeat steps 7-8 as many times as necessary to enter the 
desired extension name.
Note: Press the FLASH key to clear the entire entry.
11.   Press the HOLD key when finished. Next extension number displays
12.   To enter another extension name, press the CONF key and 
repeat steps 5-11.EXT NO.=>
EXT NAME displays
Action Result 
						

							3-40 DBS 576HD (USA) issued September 2001 576-50-700
Chapter 7. SLT Features Section 700 - Operation
b.  Press the third FF key from the left on the bottom row.
Example 2. Small-Display Phone
Refer to the following diagram to determine which one-touch key to press. (See step 7-8 above.)
To  e n t e r  D:
a.  Press the first one-touch key from the left on the bottom row.
G H I J K L M N O P Q R S T U V W X A B C D E F Y Z . , ’ -
a b c d e fg h i j k lm n o p q rs t u v w xy z : & / sp 
						

							Section 700 - Operation Chapter 7. SLT Features
576-50-700 DBS 576HD (USA) issued September 2001 3-41
b.  Press the fourth FF key from the left on the bottom row.
To  e n t e r  o:
a.  Press the third one-touch key from the left on the top row.
b.  Press the third FF key from the left on the bottom row.
Hardware Requirements
•N/A
END MODE
END MODE
PROG
CONF 
						

							3-42 DBS 576HD (USA) issued September 2001 576-50-700
Chapter 7. SLT Features Section 700 - Operation
Related Programming
•N/A
Considerations
• Extension names can be up to 10 characters in length.
• The ability to make extension name assignments is allowed/restricted to anyone with a COS that 
allows access to User Maintenance features. (See Chapter 4 “User Maintenance” of this 
document.)
Speed Dial Name Assignments
You can assign names to PSD numbers from a display telephone without entering the programming 
mode. If allowed in the Extension COS, you can also assign names to SSD numbers.
Operation
PSD Names:
To set PSD names using a large-display or small-display phone:
Action Result
1.   Lift the handset or press the ON/OFF key.
2.   Press the PROG key.
3.   Press the * key.
4.   Enter 0 for the PSD Name Assignment mode.A B C D E F P80 displays (where P80 = 
PSD bin 80)
5.   Press the up or down arrow key to display the desired PSD 
bin number.A B C D E F PXX displays (where PXX 
= desired PSD bin number)
6.   Enter the extension name:
•   If using a large-display phone, press the soft key next 
to the desired row of letters. (See Example 1 on page 
3-39.)
•   If using a small-display phone press the appropriate 
one-touch key. (See Example 2 on page 3-40.)
Note: Press the FLASH key to clear any existing data
7.   Use the bottom row of FF keys to select a single letter. 
•   See “Example 1. Large-display phone” on page 3-39.
•   See “Example 2. Small-display phone” on page 3-40.
Notes:
•   Press the * key to erase a single entry.
•   Press the # key to enter a space.
8.   Repeat steps 6-7 as many times as necessary to enter the 
desired PSD name.
Note: Press the FLASH key to clear the entire entry.
9.   Press the HOLD key when finished. Next PSD bin number displays
10.   To enter another speed dial name repeat steps 5-9.