Nortel Modular Ics 6.0 Installer Guide

System prgrming / 441
P0992638 03Modular ICS 6. 0 Installer Guide
If the number is less than 13, the display shows AM. Press 
CHANGE
 to select PM, if required. Press OK to accept.
4. Press ≠. Minutes: 00 displays.
5. Press CHANGE
 and enter the minutes (00 to 59).
Configuring alarms and expired alarms settings
Use this feature to create the alarm settings that will govern the 
alarm features for both the administrative and room sets.
1. At the Hospitality heading, press ≠ until Alarm 
displays.
2. Press...

442 / Network Services
Modular ICS 6.0 Installer GuideP0992638 03
Network Services
The headings that appear under Network Services, depends on 
which profile the system is running. 
Profiles 2 allows ETSI line connections, therefore, systems 
running this profile may have access to the two ETSI features. 
The service provided on the line by your service provider 
determines if these features are available.
Profiles 1, 2, and 4 support MCDN over PRI SL-1 lines.
ETSI: Network diversion and MCID (profile 2...

Network Services / 443
P0992638 03Modular ICS 6. 0 Installer Guide
Network Call Diversion
Norstar Network Call Diversion (NCD) is a network function 
that allows forwarding and redirection of calls outside the 
Norstar network when using an ETSI ISDN line. Functionality 
is similar to that of External Call Forward (ECF).
NCD redirects calls using the same line on which they arrive. 
Call forward is efficient since there is no need for additional 
outside lines.
Forwarding calls externally from an...

444 / Network Services
Modular ICS 6.0 Installer GuideP0992638 03
Call Forward on Busy (CFB)—implemented on Norstar 
Call Forward Busy.
Call Forward on No Response (CFNR)—implemented on 
Norstar Call Forward No Answer.
Programming and restrictions
NCD features are accessed through existing Norstar features. 
Extensions requiring redirection must be programmed 
individually to either CFAC or SLR. CFB or CFNA must be 
set during programming. Allow redirect must be set to Yes 
for each extension, in...

Network Services / 445
P0992638 03Modular ICS 6. 0 Installer Guide
Malicious call identification (MCID)
The MCID feature allows the user to press ²¡áàto 
have call information recorded on the central office system for 
an incoming call on a specific line (ETSI PRI lines, only).
The user must invoke the feature code either during the active 
call or within 30 seconds (time varies on different networks) 
after the caller hangs up. The feature will not work once the 
called party hangs up.
Note:  This...

446 / Network Services
Modular ICS 6.0 Installer GuideP0992638 03
To program these features:
1. With the display showing System prgming press 
‘ until the display shows NetworkServices.
2. Press ≠. ETSI displays.
3. Press ‘. MCDN displays.
4. Press ≠. NetwkICCL displays.
5. Press CHANGE
 to choose either Y (yes) or N (no). Default is 
No.
6. Press ‘. TRO displays.
7. Press CHANGE
 to choose either Y (yes) or N (no). Default is 
No.
8. Press ‘. TAT displays.
9. Press CHANGE
 to choose either Y (yes) or N...

Telco features / 447
P0992638 03Modular ICS 6. 0 Installer Guide
Telco features
Currently the two features accessed under this heading are the 
settings for the voice mail connections for your system, and 
how to set up outgoing name and number blocking (ONN).
With the display showing System prgming press ‘ 
until the display shows Telco features.
VMsg ctr tel#s
If you subscribe to a voice message service outside  of your 
local system, you can access it through your Norstar system. 
This includes...

448 / Telco features
Modular ICS 6.0 Installer GuideP0992638 03
6. Press CHANGE and enter the telephone number for the voice 
message system.
7. Press – to move up a level.
8. Press ‘ to move to the next Voice message 
center.
9. Repeat steps 2 to 6 for however many voice message 
centers you want to enter.
Outgoing Name and Number Blocking
Outgoing Name and Number blocking blocks the outgoing 
name and number on a per call basis when the user presses 
²¡Úá
ONN blocking is cancelled with ²£¡Úá
When this...

Telco features / 449
P0992638 03Modular ICS 6. 0 Installer Guide
Programming the analog vertical service code (VSC)
1. Press ≠. Analog VSC displays.
2. Press ≠. Tone:None displays.
3. Press CHANGE
 to enter a new tone dialing Name and 
Number blocking VSC. 
The VSC for tone trunks can include a maximum of 
10 digits consisting of the CO Pause (²à¡), and 
digits 0-9, *, and #.
4. Press ‘. Pulse:None displays.
5. Press CHANGE
 to enter a new pulse dialing Name and 
Number blocking VSC. 
The VSC for pulse...

450 / Telco features
Modular ICS 6.0 Installer GuideP0992638 03
Setting up the modules for ONN blocking
To utilize ONN blocking, the CO is alerted by two methods, 
the Vertical Service Code (VSC) or suppression bit method. 
Each method depends on the type of trunk involved in placing 
the outgoing call. 
Analog trunks use a dialing digit sequence called VSC. Most 
COs use the suppression bit method for ONN. You will need 
to use the VSC ONN if your CO does not support the 
suppression bit method. The VSC...