Nortel Modular Ics 6.0 Installer Guide

System prgrming / 411
P0992638 03Modular ICS 6. 0 Installer Guide
CAP assignmentInstaller password required
This setting designates a telephone as a  central answering 
position (CAP). The CAP must be an M7324 telephone, and 
may have one or two CAP modules attached. A maximum of 
five CAPs can be installed in a Norstar system.
The CAP may be used to:
monitor the busy/not busy and Do Not Disturb status of 
Norstar telephones
answer external calls on up to 120 lines, and extend calls 
to other Norstar...

412 / System prgrming
Modular ICS 6.0 Installer GuideP0992638 03
Use ≠, CHANGE and the dialpad to enter the internal 
number of the M7324 telephone to be designated a CAP.
Dialing PlanInstaller password required
The dialing plan acts as a system directive that determines how 
a number will be dialed out by the system. This feature works 
with enbloc dialing, and, therefore, is only used for PRI lines.
The Dialing Plan has these features:
allows public or private routing for network calls
private...

System prgrming / 413
P0992638 03Modular ICS 6. 0 Installer Guide
determine when a complete number has been dialed. The 
PSTN DN Length Table is used by the PRI trunk to determine 
when a complete PSTN DN has been dialed. Entries in the DN 
Length table consist of two fields: Prefix and DN Length.
Defining dialing plans:
At System prgrming/Dialing plan:
1. Press ≠. Private Network:None displays.
2. If you are defining a dialing table for a private network, 
press ≠. Refer to Private networks on page...

414 / System prgrming
Modular ICS 6.0 Installer GuideP0992638 03
Private network: CDP
If your dialing plan needs to use steering codes to navigate to 
other networks, specify a coordinated dialing plan (CDP).
1. At Type:None, press CHANGE 
until CDP displays.
2. Press ‘. PrivNetID:1 displays.
3. Press CHANGE
, and enter a new private network id.
Note:  If you are specifying a private network that has been 
created using SL-1 (MCDN) lines, the private network 
id is part of the set DN (for instance,...

System prgrming / 415
P0992638 03Modular ICS 6. 0 Installer Guide
5. Press CHANGE and use the dialpad to enter a location code.
Note:  This code must be unique to your system.
6. Press ‘. Priv DN len:3 displays.
7. Press CHANGE
 to choose a new private DN length. (3-14)
Note:  The Private DN length must match the DN lengths 
being used by the other systems in the network. This is 
what enbloc dialing uses to determine when the 
complete number has been dialed.
Public networks
When you identify public DNs...

416 / System prgrming
Modular ICS 6.0 Installer GuideP0992638 03
Dial Timeout
Dial Timeout (interdigit timeout) specifies how long the ICS 
will wait between user-dialed digits. This value allows the ICS 
to determine when the user has stopped dialing. The value is 
programmed under System progrming, Dialing Plan.
The user can also use the # key to tell the ICS that they are 
finished dialing. However, this is not usually required except 
for international calls where the number of digits dialed for...

System prgrming / 417
P0992638 03Modular ICS 6. 0 Installer Guide
Digits assigned by default to settings
Line pool codesInstaller password required
This setting allows you to assign a line pool access code for 
each of the 15 line pools (A to O). These codes are used to 
specify the line pool you want to use for making an outgoing 
external call.
If your system is installed without expansion cards, the DN  
default is two digits. Therefore, B1 DNs will be from 21 to 52 
and the B2 DNs are assigned from...

418 / System prgrming
Modular ICS 6.0 Installer GuideP0992638 03
Park prefixInstaller password required
The Park prefix is the first digit of the call park retrieval code 
that must be entered to retrieve a parked call. If the Park prefix 
is set to None, calls cannot be parked. 
Press CHANGE
 to select the setting: 1 to 9, None, or 0.
Tips - The code can be one to four digits in length.
A line pool access code can be the same as an  external line 
access code. In this case, the line pool access code...

System prgrming / 419
P0992638 03Modular ICS 6. 0 Installer Guide
External codeInstaller password required
External code allows you to assign the external line access 
code. This code is used to allow M7100, T7100 sets, and 
Analog Terminal Adapters (ATA2) to access external lines.
Press CHANGE
 to select the setting: 0 to 9, or None.
Direct-dial #
Installer password required
Direct-dial digit allows you to dial a single system-wide digit 
to call a specific telephone, called a direct-dial telephone.
If...

420 / System prgrming
Modular ICS 6.0 Installer GuideP0992638 03
Press CHANGE to select the setting:  1 to 9, None, or 0.
Auto DN
Installer password required
For calls answered without DISA, no password is required to 
access the Norstar system. The  Class of Service (COS) that 
applies to the call is determined by the COS for the trunk on 
which the user is calling.
1. Use CHANGE
 and the dialpad to enter the digits to be 
received from the auto-answer trunk. 
2. Press CLR
 to set the Auto DN back to...