Nortel Modular Ics 6.0 Installer Guide

System prgrming / 421
P0992638 03Modular ICS 6. 0 Installer Guide
DISA DNInstaller password required
For calls answered with DISA, the system presents a stuttered 
dial tone to prompt a caller to enter a valid password. The 
Class of Service (COS) that applies to the call is determined by 
this COS password. 
Once a remote user is on the Norstar system, the DISA DN can 
be used to change the existing Class of Service. This gives you 
greater flexibility when you create access privileges. For 
example,...

422 / System prgrming
Modular ICS 6.0 Installer GuideP0992638 03
Carrier CodesInstaller password required
If you are routing calls with different carriers as you change 
schedules, you need to be able to define the access codes for 
each carrier you use.
A multi-digit Carrier Access Code (CAC) contains an Equal 
Access Identifier Code (EAIC) followed by a 
Carrier Identification Code (CIC). The CIC identifies the 
carrier to be used to handle the call. The Carrier Access Code 
table stores the CAC digit...

System prgrming / 423
P0992638 03Modular ICS 6. 0 Installer Guide
Remote access
Remote access packages allow you to control the remote use 
of Norstar line pools. Create a remote access package by 
defining which of your system line pools will be able 
accessible. You then assign the package to individual lines 
(using Rem line access), and to a particular Class of Service 
password (Remote pkg in COS passwords).
Rem access pkgs
Use ≠ and the dialpad to select the remote access 
package you want to...

424 / System prgrming
Modular ICS 6.0 Installer GuideP0992638 03
Remote access packages defaults
ParameterSquarePBXHybridCentrexDID
Package 00 Prohibits remote access to line pools, Page, remote 
monitoring and administration. Cannot be changed.
Package 01
Line pool access
Y for Pool A
N for Pools B to O and PRI-A and PRI-B
Packages 02 - 15
Line pool access
N for Pools A to O and PRI-A and PRI-B
Tips - You can use COPY and the dialpad to copy settings 
from one remote package to another.
The line pool...

System prgrming / 425
P0992638 03Modular ICS 6. 0 Installer Guide
Changing Companion DN typeInstaller password required
This Companion setting is applicable for MICS-XC 6.0 
systems.
On startup, the DN default ranges are:
desk sets: 221-605
portable sets (Companion): 637-666
ISDN devices: 667-696 
BRI S-loops may have more than one DN associated to 
each loop.
Note that the DN range 637 to 696 can be used by either 
portable telephones or ISDN S-loops. 
You can assign all 60 of the DNs to portable...

426 / System prgrming
Modular ICS 6.0 Installer GuideP0992638 03
1. Press CHANGE to select the DN type setting: ISDN or 
Portable.
2. Press STATE
 to show whether the number is: Assigned, 
Registered, Available, Pending, or I n  u s e  b y  s y s t e m 
(currently being used by an ISDN device).
If an ISDN DN is being changed, the display may show
Disrupt service? Press No
 to leave the value as ISDN, or 
Yes
 to remove the ISDN DN from use by the system.
Note:  If you change an ISDN DN that has a device...

System prgrming / 427
P0992638 03Modular ICS 6. 0 Installer Guide
DN lengthInstaller password required
This feature allows you to change the number of digits for all 
DNs. The maximum length is seven. The default, and 
minimum length, is 3.
1. Press CHANGE
 to select the setting: 3, 4, 5, 6, or 7. 
2. Press  ‘ to save the new DN length. 
The display shows Drop data calls?.
3. Press YES
 to save the new DN length. 
NO
 restores the original value.
Tips - A DN length change, if required, should be the...

428 / System prgrming
Modular ICS 6.0 Installer GuideP0992638 03
Nat’nl length (profile 2, only)Installer password required
This feature allows you to change the number of digits that the 
system will expect to see for a national telephone number.
1. Press CHANGE
 to select the setting: (default is 10). 
2. Press YES
 to save the new DN length. 
Make/Break (profile 2, only)Installer password required
This feature allows you to change the ratio of your system.
1. Press CHANGE
 to select the setting to...

System prgrming / 429
P0992638 03Modular ICS 6. 0 Installer Guide
BusName
Norstar will display the name of the calling party when it is 
provided both Private or Public ISDN PRI and BRI interfaces. 
The displayed name may include information such as the 
Receiving Calling Name, Receiving Redirected Name, and/or 
Receiving Connected Name. The outgoing name is the 
business name concatenated with the set name. 
Network name display supported by protocol
Receiving and Sending Calling Party Name
Network name...

430 / System prgrming
Modular ICS 6.0 Installer GuideP0992638 03
If the Calling Party Name is unavailable it may be 
displayed on the Called Party set as Unknown name.
The system supports sending the calling party name, which 
is the Business Name and Set Name concatenated together, 
on calls originated by the Norstar system.
For information on programming your Feature assignment, 
see Feature assignment (CLID alignment) on page 330.
The Set Name will only be sent if the OLI for the Set is 
configured....