Nortel Modular Ics 6.0 Installer Guide

System prgrming / 431
P0992638 03Modular ICS 6. 0 Installer Guide
Programming Network Name Display
The Business Name and the Set Name make up the 
information that is used for the outgoing Calling name or 
connected name.
Calling/connected name is only sent once the Business Name 
is programmed. 
To program the Business Name start with the display showing 
System prgming.
1. Press ≠.The display shows Hunt groups. 
2. Press ‘ until the display shows BusName:. 
3. Press CHANGE
 and use the keypad to enter...

432 / System prgrming
Modular ICS 6.0 Installer GuideP0992638 03
Outgoing Name and Number Blocking
When activated, ²¡Úá blocks the outgoing name and 
number on a per call basis. When this feature is used, the call 
is flagged to the CO so that the name and number will not be 
presented to the person being called.
On analog and BRI trunks, a call blocking digit sequence is 
sent to the CO before sending the dialout digits. You can 
change this digit in a Norstar programming session and set it 
to the...

System prgrming / 433
P0992638 03Modular ICS 6. 0 Installer Guide
Call by Call service selection for PRIInstaller password required
Call by Call service selection allows a user to access services 
or private facilities over a PRI line without the need for 
dedicated facilities. The different services represent different 
types of access to the network. Various services are available 
depending on the chosen protocol. The list below identifies the 
supported services
Call by Call service selection is...

434 / System prgrming
Modular ICS 6.0 Installer GuideP0992638 03
OUTWATS
(Outward 
Wide Area 
Telecommu-
nications)This outgoing call service allows a Norstar user 
to call telephones in a specific geographical area 
referred to as a zone or band. Typically a flat 
monthly fee is charged for this service.
INWATS 
(Inward Wide 
Area Tele-
communica-
tions)This long distance service allows a Norstar user 
to receive calls originating from specified areas 
without charge to the caller. A toll-free number...

System prgrming / 435
P0992638 03Modular ICS 6. 0 Installer Guide
Norstar supported Call by Ca ll Services by protocol
a.  A shaded box indicates that the protocol does not support the service.
b.  DMS-250 Sprint and UCS support incoming FX only (i.e. Network-to-
Norstar). DMS-250 MCI does not support FX.
c.  NI-2 allows two Tie operating modes: senderized and cut-through. Norstar 
will only support senderized mode.
d.  Rates greater than 64 kbps will not be supported.
e. Bell Canada VNET.
f.   Not all...

436 / System prgrming
Modular ICS 6.0 Installer GuideP0992638 03
åunder System programming, specify the minimum and 
maximum values for the pools
åunder Hardware choose PRI card and select the protocol
Line Pools
All lines in a PRI interface are in the same PRI line pool. This 
pool cannot contain any non-PRI lines. There is one PRI pool 
available for each PRI interface on the CSU. 
Depending on the order that the cards are configured as PRI, 
Pool PRI-A represents lines 1 to 30, and Pool PRI-B...

System prgrming / 437
P0992638 03Modular ICS 6. 0 Installer Guide
PRI Call by Call Limits
PRI pool limits for Call by Call services allows you to 
configure limits for service types without interacting with the 
CO. This feature sets the minimum and maximum number of 
incoming and outgoing calls per service type for the PRI pool. 
The number of active calls will be tracked so that whenever a 
call is being set up, a check will be made to determine if it will 
be allowed. Calls will not be allowed if they...

438 / System prgrming
Modular ICS 6.0 Installer GuideP0992638 03
6. Press ‘. If it applies, the display shows Max 
incoming:23. Press CHANGE
 to enter a different number. 
7. Press ‘. The display shows Min outgoing:4. 
Press CHANGE
 to enter a different number. 
8. Press ‘. The display shows Max outgoing:23. 
Press CHANGE
 to enter a different number. 
Release Reasons
This feature is useful for diagnostic purposes. It shows the 
reason why an ISDN call has been released. The Release 
Reason can be...

System prgrming / 439
P0992638 03Modular ICS 6. 0 Installer Guide
Programming Hospitality Services
The Hospitality heading accesses the settings for the room and 
alarm information.
With the display showing System prgming press ‘ 
until the display shows Hospitality.
Room/desk information
Use this setting to assign set DNs to a specific room.
1. At the Hospitality heading, press ≠. 
Room/desk info displays.
2. Press ≠. Show set: displays.
3. Enter a room set number or press LIST
 and press 
‘ until you...

440 / System prgrming
Modular ICS 6.0 Installer GuideP0992638 03
Call restrns
You can set up call restrictions based on room occupancy 
states. This setting affects the Room occupancy feature.
1. At the Hospitality heading, press ≠ twice. 
Call restrns displays.
2. Press ≠. Vacant:00 displays.
3. Press CHANGE 
and enter the filter that defines the 
restrictions for your hospitality system. Refer to Filters on 
page 322
4. Repeat steps 2 and 3 for the other room occupancy states.
The table below shows an...