Nortel Modular Ics 6.0 Installer Guide

Port/DN status / 491
P0992638 03Modular ICS 6. 0 Installer Guide
Checking the device version numberInstaller password required
From the Norstar device identification display:
1. Press VERSN
 (if it is available). 
The display shows the version number of the device.
2. Write this number on the appropriate Maintenance record.
To return to the Norstar device identification display from 
the display showing the version number, do one of the 
following:
Press OK
 to retain the same port number. Press...

492 / Port/DN status
Modular ICS 6.0 Installer GuideP0992638 03
How the device state is shown on the display
Disabling a device Installer password required
To disable immediately when the display indicates the device 
is busy:
1. Press DISABLE
. Disable at once? displays.
2. Press YES
. 
The system prompts the device user and disables the 
device in one minute (or immediately, if the device is idle). 
Press NO
 to leave this display without disabling the device.
DisplayState of device
Busy
DISABLE OKThe...

Port/DN status / 493
P0992638 03Modular ICS 6. 0 Installer Guide
Displays
The following table shows examples of the sequence of 
messages that might appear on a telephone when you disable a 
device.
Examples of display messages
Enabling the device Installer password required
When the display shows you that the device is disabled:
Press ENABLE
. Enabling... briefly displays. 
The device is immediately enabled and the display shows 
Idle. 
Please hang up
Maintenance testOccurs on a busy telephone before...

494 / Port/DN status
Modular ICS 6.0 Installer GuideP0992638 03
Returning to the beginningInstaller password required
From the display showing the state of the device:
1. Press OK
.
2. Press  – until the you reach Port/DN status. 

Module status / 495
P0992638 03Modular ICS 6. 0 Installer Guide
Module status
Module status allows you to:
look at the inventory of Station Modules, Trunk Modules, 
Data modules, and modules inside the Integrated 
Communication System (ICS)
check the number of Trunk Cartridges in a module
check the state of the module or its cartridges
disable or enable the module or its cartridges
isolate any malfunctioning modules
disable a module before replacing it
clear a hung line by disabling and enabling...

496 / Module status
Modular ICS 6.0 Installer GuideP0992638 03
Checking the number of Cartridges Installer password required
Start from the module inventory display, which shows the 
number of Trunk Cartridges connected to the module you 
chose, for example, Mod 04: 3 cards.
1. Press CARD
. 
If there is a Trunk Cartridge in a slot, the display shows 
that four lines are connected, for example,
Card 1: 4 lines. 
2. Press  ‘ or  “ to check for Trunk 
Cartridges in the other slots.
3. Press MODULE
 to...

Module status / 497
P0992638 03Modular ICS 6. 0 Installer Guide
Checking the state of a cartridgeInstaller password required
Start from the display that shows the number of lines 
connected to the Trunk Cartridge you chose, for example, 
Card 1: 4 lines.
1. Press STATE
. 
The display shows the state of the cartridge. Some 
examples of this display are shown in the previous table.
2. Press ‘ or  “ to check the Trunk 
Cartridges connected to the other Trunk Modules.
3. If required, you can disable or...

498 / Module status
Modular ICS 6.0 Installer GuideP0992638 03
Disabling a module or its cartridges Installer password required
From the display showing the state of the module or cartridge:
1. Press DISABLE
. Disable at once? displays.
2. Press YES
. 
The system disables the module or cartridge in one minute. 
If the status is idle, the system disables the module or 
cartridge immediately.
Press NO
 to leave this display without disabling the module 
or cartridge.
Enabling a module or its cartridge...

System test log / 499
P0992638 03Modular ICS 6. 0 Installer Guide
System test log
The System test log shows you a list of diagnostic test results, 
audits, event messages, and alarm codes. By using this feature 
you can:
check the items in the log
check the current alarm (if there is one)
check when each item in the log occurred
check the number of consecutive occurrences of an event 
or an alarm
erase the log
The System test log holds a maximum of 20 items. You should 
check and record these items...

500 / System test log
Modular ICS 6.0 Installer GuideP0992638 03
Checking the current alarm Installer password required
If you want to quickly check the highest severity alarm before 
viewing all the log items, start with the display showing I t e m s  
in log:.
1. Press ALARM
. 
The display shows an alarm code if there is a current alarm.
If there is no current alarm, ALARM
 does not appear on the 
display.
2. Press OK
 to return to Items in log:.
All alarms are recorded as items in the System test...