Nortel Compact Ics 6.1 Installer Guide

System prgming / 221
P0603539  02Compact ICS 6.1 Installer Guide
Setting SWCA controls
You can assign up to 16 System Wide Call Appearance (SWCA) keys to 
each telephone in a group. This is performed using the Key programming 
heading under 
Terminals&Sets, User Preferences headings. SWCA 
controls are controlled by feature codes 
²¥ÞÛâto 
²¥ÞÜÞ. The user can also program this feature using these 
feature codes. Refer to the Compact ICS System Coordinator Guide for 
instructions about programming...

222 / System prgming
Compact ICS 6.1 Installer GuideP0603539  02
1. Under Featr settings, press ≠. The display shows 
Backgrnd music:.
2. Press 
‘ until the display shows SWCA Cntrl:.
3. Press 
≠. The display shows Auto Associate: N.
4. Press 
CHANGE to choose the Y or N option. 
5. Press 
‘. The display shows Invoke by Hold: N.
6. Press 
CHANGE to choose the Y or N option. 
7. Press 
¨ to exit or ‘ to continue programming.
CLID Match
This setting determines the minimum number of digits that an external...

System prgming / 223
P0603539  02Compact ICS 6.1 Installer Guide
Silent Monitor
You can monitor Hunt group members using a two-line display telephone 
that has been designated as a supervisor telephone. 
You have the choice of silently monitoring the conversation, or providing 
a tone to the other two parties to indicate that the line is being monitored. 
This setting is the same for all supervisor telephones. Refer to the process 
below to determine the setting.
1. Under 
Featr settings, press ≠. The...

224 / System prgming
Compact ICS 6.1 Installer GuideP0603539  02
D-Dial1
For the direct-dial telephone, indicate whether it is an internal or external 
number.
Use 
≠ and CHANGE to select the setting: Intrnl, Extrnl, or None.
Number
Enter the internal or external number that the system will automatically dial 
when someone enters the direct-dial digit.
Use 
≠, CHANGE, and the dialpad to enter the telephone number. 
The default number for the direct-dial telephone is 21.
Line selection
If you assign an...

System prgming / 225
P0603539  02Compact ICS 6.1 Installer Guide
CAP/KIM assgnInstaller password required
This setting designates a telephone as a central answering position (CAP). 
The default assignment is 
None. CAP configurations consist of one of the 
following:
M7324 telephones with attached CAP  modules. A maximum of 1 
CAP can be installed in a Norstar system.
T7316E telephones with attached KIMs. The maximum number of 
KIMs on a system, depends on the configuration of the KIM module. 
Refer to...

226 / System prgming
Compact ICS 6.1 Installer GuideP0603539  02
.
Tips - If CAP modules are attached to a telephone 
that has not been programmed as a CAP, then no CAP 
settings are assigned. 
If a CAP module is relocated with the telephone, the 
settings are retained. 
If you replace a T7324 CAP unit with a T7316E unit, only 
the line assignments will be copied to the new telephone, 
but not to the KIM. The telephone programming will 
revert to the default settings.
If you move an OKIM from one T7316E...

System prgming / 227
P0603539  02Compact ICS 6.1 Installer Guide
Access codes
Access codes are used by the system to direct calls to the correct lines and 
destinations. If the codes conflict, some of the features on the system will 
not work. The table of default settings can help you plan your access codes 
so there are no conflicts. It assumes you are using a fully expanded 
Compact ICS. See the wiring information in the Installation chapter for DN 
numbering for smaller configurations.
Digits...

228 / System prgming
Compact ICS 6.1 Installer GuideP0603539  02
Line pool codesInstaller password required
This setting allows you to assign a line pool access code for each of the 
three line pools (A to C). These codes are used to specify the line pool you 
wish to use for making an outgoing external call. 
Use 
≠, CHANGE, the dialpad, and OK to program the access code. 
The default access code is 
None..
Park prefixInstaller password required
The Park prefix is the first digit of the call park...

System prgming / 229
P0603539  02Compact ICS 6.1 Installer Guide
External codeInstaller password required
External code allows you to assign the external line access code. This code 
is used to allow M7100 and T7100 telephones and Analog Terminal 
Adapters (ATA) to access external lines.
Use 
CHANGE to select the setting: 1 to 9, None, or 0.
Tip - The Park prefix cannot be the same as 
the direct-dial digit
the external line access code
the first digit of a DN
the first digit of a line pool access...

230 / System prgming
Compact ICS 6.1 Installer GuideP0603539  02
Direct-dial #Installer password required
Direct-dial digit allows you to dial a single, system-wide digit that can be 
used to call a specific telephone, called a direct-dial telephone. 
Press 
CHANGE to select the setting: 1 to 9, None, or 0.
Auto DNInstaller password required
For calls answered without DISA, no password is required to access the 
Norstar system. The Class of Service (COS) that applies to the call is 
determined by the COS...