Nortel Compact Ics 6.1 Installer Guide

ETSI: Network features (profile 2) / 251
P0603539  02Compact ICS 6.1 Installer Guide
An extension with CFB, CFNA and CFAC programmed will give priority 
to CFAC for diversion.
Selective Line Redirection
Selective Line Redirection (SLR), also referred to as Line Redirection, is 
enhanced for use with digital lines and operates in conjunction with NCD.
Diversion by SLR takes precedence over diversion by CFAC. An SLR line 
cannot be diverted by CFAC. If the call arrives on an extension with SLR 
programmed,...

252 / ETSI: Network features  (profile 2)
Compact ICS 6.1 Installer GuideP0603539  02
Note:If the alerting extension is not the CLID extension for that line, the 
line appearance can be pressed to briefly display the information. 
Pressing 
²¡ÚÚ or INFO while the call is active invokes 
Call Info.When Norstar requests that an incoming call be 
redirected by the distance network, Norstar does not inform the 
network of the redirecting DN. In this case, the diverted-to party 
will not see the diverting...

Telco features / 253
P0603539  02Compact ICS 6.1 Installer Guide
Telco features
VMsg centr tel#s
If you subscribe to a voice message service outside your office, you can 
access it through your Norstar system. This setting specifies the external 
telephone numbers that are dialed by the Message feature to retrieve voice 
messages. Use 
≠, ‘, CHANGE, and the dialpad to enter 
the external number.
The default for each voice message center is 
No number.
Outgoing Name and Number Blocking
When activated,...

254 / Telco features
Compact ICS 6.1 Installer GuideP0603539  02
For Analog VSC
4. Press 
≠. The display shows Tone:None .
5. Press CHANGE to enter a new tone dialing Name and Number blocking 
digit sequence.
6. Press 
‘. The display shows Pulse:None.
7. Press CHANGE to enter a new pulse dialing Name and Number blocking 
digit sequence.
For BRI VSC
8. Press 
≠. The display shows Code .
9. Press CHANGE to enter a new ONN code. 

Software Keys / 255
P0603539  02Compact ICS 6.1 Installer Guide
Software Keys
In order to upgrade a restricted  feature cartridge or enable the remote 
administration feature (I-RAD) you must first purchase the required 
Software keys. To obtain the required Software key, call the Integrated 
Voice Response (IVR) access line at: 1-800-4NORTEL (667835), then 
use Express Routing Code 1599.
Entering the keys is performed using the following programming settings 
under 
Software Keys.
SysID
Press ≠ at...

256 / Hardware
Compact ICS 6.1 Installer GuideP0603539  02
Hardware
Hardware is where you view and change the settings for the Trunk 
Cartridges and BRI Cards installed in the ICS. 
The ISDN section provides an overview of configuration and programming 
for ISDN resources, including step-by-step instructions for programming. 
This section provides more detailed information about individual headings 
and settings.
Hardware settings that appear for each cartridge or  card type
Setting Loop 
start...

Hardware / 257
P0603539  02Compact ICS 6.1 Installer Guide
Cd1-KSUInstaller password required
Press ≠ to display the Trunk Cartridge or BRI Card in the ICS. 
Press 
CHANGE to select a card type: Loop, BRI-U2, BRI-U4, or BRI-ST.
If your system is using a restricted feature cartridge that has not been 
upgraded, you cannot select the 
BRI-ST and BRI-U4 card types, or 
configure the second cartridge or card in the ICS (
Cd2-KSU). 
KSU is commonly referred to as the Integrated Communication System 
(ICS)....

258 / Hardware
Compact ICS 6.1 Installer GuideP0603539  02
Discon timerInstaller password required
Disconnect timer allows you to specify the duration of an open switch 
interval (OSI) before a call on a supervised external line is considered 
disconnected. 
Press 
CHANGE to select the setting: 60, 100, 260, 460, or 600 milliseconds.
LoopsInstaller password required
The display shows the loops found on the BRI Card.
If your system is using a restricted feature cartridge that has not been 
upgraded, you...

Hardware / 259
P0603539  02Compact ICS 6.1 Installer Guide
TypeInstaller password required
Press CHANGE to select the loop type. If the card type is BRI-ST, the loop 
type can be 
S, or T. If the card type is BRI-U2 or BRI-U4, the loop type can 
be 
LT or NT.
The BRI Card must be disabled under 
Module Status in Maintenance 
before this setting can be changed. You can change the setting if the card 
has not yet been installed in the ICS slot.
LinesInstaller password required
There are two lines for each...

260 / Hardware
Compact ICS 6.1 Installer GuideP0603539  02
No SPIDs assigndInstaller password required
T, S, and NT-loops can be assigned a service profile identifier (SPID) as 
supplied by your service provider. No SPIDs are assigned by default .
When the loop type is T or NT, calls on the loop are handled for a network 
connection only. If any other ISDN equipment is connected to the loop, it 
must be configured as an S loop to ensure proper call handling.
Press 
ADD and enter the first or second SPID...