Nortel Compact Ics 6.0 System Coordinator Guide

Using the Hospitality features / 171
P0992670 03 Compact ICS 6.0 Syste m Coordin ator Guide
7. Press CHANGE until you find the number you want (1-5). 
8. Press 
‘. Retry intrvl:4 displays.
9. Press 
CHANGE until you find the number you want (2, 4, 6, or 8). 
10. Press 
‘. Attn duration: 15 displays.
11. Press 
CHANGE until you find the number of seconds you want (10, 15, 
20, 30, 40, 50). 
12. Press 
‘. Time format:12 hr displays.
13. Press 
CHANGE to choose either 12hr or 24hr. 
14. Press 
‘. Expired...

172 / Using the Hospitality features
Com pact ICS 6.0 System Coordinator Guide P0992670 03
4. Press VIEW. The set displays Alrm: 07:00am OFF:.
If the alarm time is correct, press the 
ON/OFF display key.
If you want to change the time, enter a new four-digit alarm time.
If the clock uses a 24-hour format, enter an hour between 00 and 23, 
and minutes between 00 and 59. The set displays: 
Alarm ON hh:mm
If the clock uses a 12-hour format, enter the time, then when the set 
displays: 
hh:mm AM or PM?,...

Using the Hospitality features / 173
P0992670 03 Compact ICS 6.0 Syste m Coordin ator Guide
Canceling an alarm
Canceling the alarm time for any set cancels the alarm time for all the sets 
in the same room.
Digital set: Press 
²£¡àÞ.
Analog set: Press ˚£¡àÞ.
Turning off an alarm
When the alarm rings, the user can release the ring by doing one of the 
following, depending on the type of set in the room:
Digital set: Press any button except 
³.
Analog set: Lift and replace the handset.
³acts like a snooze...

174 / Using the Hospitality features
Com pact ICS 6.0 System Coordinator Guide P0992670 03 

P0992670 03 Compact ICS 6.0 Syste m Coordin ator Guide
Telephone features
Installing Business Series Terminals
If you are connecting a Business Series Terminal for the first time, refer to 
the following illustrations as a guide.
Installing the Business Series Terminal connections
Installing to a desk jack 

176 / Telephone features
Com pact ICS 6.0 System Coordinator Guide P0992670 03
Mounting a Business Series Terminal on the wall
Mounting a Business Series Terminal on the wall
Installing without the angled base 

Telephone features / 177
P0992670 03 Compact ICS 6.0 Syste m Coordin ator Guide
Mounting a Business Series Terminal using the stand
Mount the keystation 
    onto the screws and 
slide it down. Mount the stand as shown and
insert screw. Use the screw that
came with your keystation.
 Use the key hole slots on the stand
to mark the location for the screws.
key hole slots
Connect line cord to 
wall jack. Connect cords to the  keystation,
    refer to cord connections
 Tighten screws for a secure fit. 

178 / Telephone features
Com pact ICS 6.0 System Coordinator Guide P0992670 03
Installing Norstar telephones
If you are connecting a Norstar telephone for the first time, refer to the 
illustrations below and use as a guideline.
Installing a Norstar telephone
Connect to 
jack wired from
distribution block
Connect to 
receiverConnect to jack 
wired from 
distribution block
Connect to 
receiver 

Telephone features / 179
P0992670 03 Compact ICS 6.0 Syste m Coordin ator Guide
Mounting a Norstar telephone on the wall
12
34
56 

180 / Telephone features
Com pact ICS 6.0 System Coordinator Guide P0992670 03
Naming a telephone or a line
You can assign names to identify external lines, target lines, and telephones 
assigned to specific people. During a call, the name (if programmed) is 
shown on the telephone display instead of the external line number or 
internal telephone number of the caller. Step-by-step instructions for 
adding or changing the name of a telephone or a line are in ‘‘Changing the 
name of a telephone’’ on page...