Nitsuko Digital System Administrators Guide

Note:  To have line groups, the DIGITAL SYSTEM must be equipped with an AUX
Module.
Using PBX/Centrex Lines 
When the DIGITAL SYSTEM is installed behind a PBX/Centrex, you place an
outside call as follows: 
·Use one of the above methods to get PBX/Centrex dial tone. 
·Dial a one- or two-digit PBX/Centrex Access Code to get outside dial tone. 
·Dial your number. To call a PBX/Centrex extension, you do not dial the
PBX/Centrex Access Code. To access PBX/Centrex features, see page 136.
Initial...

To place a call using Line
Dial-Up or Direct Line
(Trunk) Access or Direct
Line Group Access:
1.Lift handset. 
2.Press ICM (except at an ESL set), then dial:
-801-816 for lines 01-16
-348-363 for lines 01-16
-90-98 for line groups 00-08 
-When you press ICM, the key lights and you hear
Intercom dial tone.  
-When you dial a code, ICM goes out and you hear
outside dial tone. 
 OR 
Press key for line group. You hear outside dial tone. 
3.Dial number.
To place a call on a
PBX/Centrex line:
1.Lift handset....

For Prime Line: 
Program 17To assign a line to a key to an extension (LK + Line
number 01-16 + #)
Program 18 (II)To enable/disable a Prime Line key for an extension (PLA
+ # + Press key + Y or N + #)
Program 15To assign program access level 2-5 to extensions so they
can program their own Prime Line key (PGM ACC
LEVEL = 02-05 + #)
For Line Dial-Up:
Program 18 (I) To allow/deny Line Dial-Up for an extension (LDU + # +
Y or N + #)
For Direct Line Access:
Program 1To allow/deny Direct Line (Trunk) Access in...

P aging
&
Make an important announcement to a group of people. Or,
quickly locate someone who is away from their phone. 
Paging lets you use your phone to broadcast an announcement over speakers.  The
announcement can be up to 90 seconds long.  There are two types of Paging:
Internal Zone Paging and External Zone Paging.
Internal Zone Paging
Internal Zone Paging lets you broadcast an announcement over the speakers of idle
Multibutton extensions.  You can page:
·A group of extensions (Internal Page Zone),...

-If you have a Page key or One-Touch Speed Dial
key for the desired zone, you can press it instead of
using steps 2-3. 
2.Press ICM (except at an ESL set).
-ICM lights and you hear dial tone. 
3.Dial Page Zone code. 
-Fo r :. . . . . . . . . . . . . Dial:
All Call . . . . . . . . . .  1 *
Zone 1 . . . . . . . . . . .  2 *
Zone 2 . . . . . . . . . . .  3 *
Zone 3 . . . . . . . . . . .  4 *
Zone 4 . . . . . . . . . . .  5 *
Zone 5 . . . . . . . . . . .  6 *
Zone 6 . . . . . . . . . . .  7 *
Zone 7 . . . ....

Program 17To assign a page zone to a key at an extension (P0 + # +
Page zone 01-07 or 00 for All Call + #)
For External Paging:
If you have External Zone 1 Paging, the system disables line port 04 in the Main
CEU. If you have External Zone 2 Paging, the system disables line port 04 in
Expansion CEU #1 (line port 04 is equivalent to line 12). To install the speakers, see
the Hardware Manual.
Program 7To enable External Page Zone 1 in the Main CEU (EXT
PAG E  Z N  1 = Y + #).
To enable External Page Zone 2...

Park
&
Be sure that a call gets sent to a person even when you don’t know
what part of the building they are in. 
Park lets you send an outside call into an Orbit (which is a special waiting state) so
that a person can pick it up from any extension in the system.  After you park a call
using a Park Orbit code, you page the person for whom it is intended.  The paged
person then dials the Park Orbit code from any extension to pick up the call.
You can park a call so it waits in a: 
·System Orbit, by using...

To pick up a parked call:To pick up a parked outside call, you must use an
extension that has access to that line.
1.Lift handset. 
-If you have a One-Touch Speed Dial key, you can
press it instead of using steps 2-3. 
2.Press ICM (except at an ESL set). 
3.For System Park: Dial announced Park Orbit Code or
press Park Orbit key for that Orbit. 
OR 
For Personal Park:  Dial *, then announced extension
number.
-The procedure for picking up Personal Park calls
also picks up other types of calls.  The...

P eripheral C ontrol Unit (PC U) Module
&
Install a PCU to get two more External Page Zones, fax switching,
alarm sensors, tone (DTMF) decoders and 500/2500 set connections.
The Peripheral Control Unit (PCU)
requires AUX Module software
version Y2.1 or higher. The PCU is
not available with Base software.
The 12SCU/PCU Peripheral
Control Unit (PCU) Module (P/N
88530) provides 12 digital station
ports and gives your system the
following additional features:
·Two External Paging Zones
Each PCU provides two...

Note: You can install up to four PCUs in a system: two in the main CEU and two in
Expansion CEU #1. You cannot install PCUs in Expansion CEU #2. For additional
PCU installation and programming instructions, refer to P/N N1853PCU01.
Initial Configuration
Not enabled.
Using the Feature
Refer to the PCU Installation and Programming Instructions (P/N N1853PCU01).
Understanding Related Programming
Refer to the PCU Installation and Programming Instructions (P/N N1853PCU01).
Peripheral Control Unit (PCU)...