NEC Neax2000 Ivs Isdn System Manual

							ND-45857 (E) CHAPTER 4
Page 71
Revision 3.0
SYSTEM DATA PROGRAMMING
DESCRIPTION DATA
Assign ISDN Local Office Code Table Number 
to each ISDN trunk.
Assign trunk route data to the route number 
assigned by CM30 YY=00.
Note 1:This data should be assigned to the B
channel trunk route. This data should
be assigned to both B channel trunk
route and D channel trunk route.
Specify the number of digits to be received on
DID.
Note:If CM35 YYY=143 is set to “1” for Event
Based CCIS, the number of digits received
on DID must be assigned.
• YY=34 
(1)  Trunk No. (000-255) assigned by CM07 
YY=02
(2)  Local Office Table No. (00-14)
15 : Not assigned
•  YY=00 (Kind of Trunk Route)
(1)   Trunk Route No. (00-63)
(2)   00:  ISDN Trunk
(1)   D channel Route No. (00-63)
(2)  15 : Not used
•   YY=02 (Call Direction)
(1) Trunk Route No. (00-63)
(2) 3 : Bothway Trunk
Note 1
•   YY=04 (Answer Signal From Distant 
Office)
(1) Trunk Route No. (00-63)
(2) 2: Answer signal arrives (ISDN Trunk)
(1) D channel Route No. (00-63)
(2) 7 : Not used
• YY=05 (Release Signal from Distant 
Office)  
(1) Trunk Route No. (00-63)  
(2) 1 : Release signal arrives
Note 2
• YY=09 (Incoming Connection Signaling)
(1)   Trunk Route No. (00-63)
(2)  08 : ISDN Indial
•   YY=11 (Toll Restriction)
(1)   Trunk Route No. (00-63)
(2)    0/3 : To be provided/Not to be provided  
Note 1
•  YY=12 
(1)   Trunk Route No. (00-63)
(2)   0 : 1 digit
1 : 2 digits
2 : 3 digits
3 : 4 digits
Note 1B
CM35
CM30
A 
						

							CHAPTER 4 ND-45857 (E)
Pag e 7 2
Revision 3.0
SYSTEM DATA PROGRAMMING
DESCRIPTION DATA
Note 1:This data should be assigned to the B
channel trunk route. For D channel trunk
rute, no data setting is required.
Note:If CM35 YYY=143, is set to “1” for Event
Based CCIS, CM35 YY=18 must be set to
“0”.
T/R: Transmitter PAD/Receiver PAD
+: Gain
T/R: Transmitter PAD/Receiver PAD
+: Gain• YY=14 (SMDR for Outgoing Call)
(1)   Trunk Route No. (00-63)
(2)   0/1 : Not to be provided/To be provided
Note 1
•   YY=15 (Kind of Call Termination 
Indicator Key/Lamp on ATT)
(1)   Trunk Route No. (00-63)
(2)   00-07 (C.O. Incoming 0-7)
Note 1
•   YY=16 (Hooking Signal Sending to 
Outside)
(1)   Trunk Route No. (00-63)
(2)   0: Not sending
Note 1
•   YY=18 (Digit conversion on DID call)
(1)   Trunk Route No. (00-63)
(2)   0 : To provide
1 : Not provided
Note 1
•   YY=19  
(1) Trunk Route No. (00-63)
(2) 0:
1:  Programmable PAD
2:  (See CM42)
3:  
4:  
5: 
6:    
7:
Note 1
B
CM35
C
CONNECTION 
PAT T E R N SPAD DATA OF DTI [dB]
DATA
=4 (T/R)DATA
=5 (T/R)DATA
=6 (T/R)DATA
=7 (T/R)
Station – DTI 3/8 3/3 3/3 3/8
Tone – DTI 0/0 0/0 0/0 0/0
COT/LDT – DTI 0/0 0/0 0/0 0/0
ODT – DTI +3/3 0/0 0/0 +3/3
DTI –DTI 0/6 0/0 0/6 0/0 
						

							ND-45857 (E) CHAPTER4
Addendum-001 Page 73
August, 1998 Revision 3.1
DESCRIPTION DATA
Note 1:This data should be assigned to the B
channel trunk route. For D channel trunk
route, no data setting is required.
Note 2:This data should be assigned to both B
channel trunk route and D channel trunk
route.
• YY=28 (Outgoing Trunk Queuing)
(1)     Trunk Route No. (00-63)
(2)  0: Restricted
For D channel trunk route, no data setting 
is required.
•   YY=39 (Trunk release by detection of 
reversal of tip and ring)
(1)   Trunk Route No. (00-63)
(2)   1 : To be released
Note 1
•   YY=90 (Assignment of BRI route for 
ISDN)
(1)   Trunk Route No. (00-63)  
(2)   2: ISDN-Basic Rate Interface
Note 2
Specify which number is adopted for corre-
sponding of virtual trunks between the offices, 
either sub-address number or ISDN Indial 
dialled-in digits.•   YYY=143
(1)   Trunk Route No. (00-63)
(2)   0: By sub-address No.
1: By dialled-in digits
Note 1
Assign ISDN Local Office Code. •   YY=05
(1)   Local Office Table No. (00-14)
assigned by CM30 YY=34
(2)   XXXXXX
(Area Code + Local Office Code: 6 digits)
Assign Service Profile ID (SPID) to each B 
channel No.•  YY=30 
(1) XX
  X
*a *b
*a: Slot No. (04-15) assigned by CM05.
*b: BCH No. (0-3)
(2)   XXXXXXXX
(Local Office Code + SPID: 8 digits)
C
CM35
CM50
CMAC
D 
						

							CHAPTER 2 ND-45857 (E)
Pag e 7 3-1
Revision 3.1
 
HARDWARE REQUIRED
PN-AUCA card ´ n 
DESCRIPTION DATA
When the data for CM35 YY = 18 is set to 
“0” (Received Digits Conversion is to be 
provided), assign the data for interpreting the 
digits received.• Y = 0 (Day Mode) 
• Y = 1 (Night Mode) 
(1) X-XXXX: Station Number received.
(2) X-XXXX: Station Number to be ter-
minated. 
DXX: Change Terminating System to:
D09: AUTO ATT.
D13: TAS 
D14: SN610 ATTCON
D16: DISA
END
CM76
D 
						

							ND-45857 (E) CHAPTER 2
Addendum-001 Page 73-2
August, 1998 Revision 3.1
This page is for your notes. 
						

							CHAPTER 4 ND-45857 (E)
Pag e 7 4
Revision 3.0
SYSTEM DATA PROGRAMMING
• For originating calls to the ISDN network, assign the following data.
• When providing Tandem Connection (Tie Line (OD/DTI) to ISDN/ISDN to Tie Line (OD/DTI)), do the fol-
lowing programming. START
DESCRIPTION DATA
Assign ISDN access code to each trunk route 
assigned by CM30 YY=00.  •
(1)
(2)Y=0-3 (Numbering Plan Group 0-3)
X-XXX (Access code)
100-163: Trunk Route No. (00-63)
Specify the timing start when making an ISDN 
call from SN610 ATTCON.(1)
(2)403  
0/1 : Not Available/Available
Specify the timing start when making an ISDN 
call from a Single Line Telephone (PB/DP), 
Multiline Terminal or SN610 ATTCON, if 
required. •
(1)Y=0
50
03-14: 3 sec.-14 sec.
If no data is set, the timing start is not 
effective.
(Dialing terminated by entering #.)
Recommended setting is 05 (5 seconds). (2)
START
DESCRIPTION DATA
Specify the combination of Trunk Routes allow-
ing the tandem connection.(1) XX XX
00-63 (Incoming Trunk Route)
00-63 (Outgoing Trunk Route)
(2) 0/1 : Allowed/Restricted
Specify the timing start when making an ISDN 
call from a station (PB/DP telephone Multiline 
Terminal) or Attendant Console for the Tandem 
Connection.•
(1)
(2)Y=0
57
03-14: 3 sec.-14 sec.
Note 1:By using this command, an ISDN call is available even if “#” is not dialed.
Note 2:This command is effective for dialing a called number (When dialing a called party subaddress, this
command is not effective).
Note 3:When the default setting is “NONE”, the timing start is not effective.
CM20
CM41
END
CM08
CM36
CM41
END 
						

							ND-45857 (E) CHAPTER 4
Addendum-001 Page 75
AUGUST, 1998 Revision 3.1
SYSTEM DATA PROGRAMMING
• When providing Tandem Connection (ISDN to CCIS/CCIS to ISDN), do the following programming.
• Specify whether the Calling Party Number (CPN) sent from ISDN is sent to the CCIS network. START
DESCRIPTION DATA
Specify the combination of Trunk routes allow-
ing the tandem connection.(1) XX  XX
00-63 (Incoming Trunk Route)
00-63 (Outgoing Trunk Route)
(2)
0/1 : Allowed/Restricted
Tandem connection by station or attendant  (1)
(2)028
0/1 : Available/Not Available
START
DESCRIPTION DATA
Maximum number of digits sent to CCIS
 network(1) 379
(2) 0 : 24 digits
Activate IAI2 message for sending ISDN CPN 
to CCIS network.
Allow sending of CPN to CCIS network.•
(1)
(2)
•
(1)
(2)YY=26
CCIS Channel No. (0-3)
0 : Active
YY=28
CCIS Channel No. (0-3)
0 : Allowed
CM36
END
CM08
CM08
CMA7
END 
						

							CHAPTER 4 ND-45857 (E)
Pag e 7 6
Revision 3.0
SYSTEM DATA PROGRAMMING
3.3 Service Data Assignment
3.3.1 Calling Party Recognition Service (Direct-In Termination (DIT)) Assignment
Refer to “Direct Inward Termination (DIT)” in the Feature Programming Manual. 
						

							ND-45857 (E) CHAPTER 4
Page 77
Revision 3.0
SYSTEM DATA PROGRAMMING
3.3.2 DID Addressing Assignment
DESCRIPTION DATA
Assign the data for DID to the Trunk Numbers 
assigned by CM07.• YY = 02 (Terminating System in Day 
Mode)
• YY = 03 (Terminating System in Night 
Mode)
(1) Trunk No. (000 – 255) assigned by CM07 
YY = 01
(2) 18: ISDN Indial
Assign the data for DID to the Trunk Routes as-
signed by CM30• YY = 00 (Kind of Trunk)
(1) Trunk Route No. (00 – 63)
(2) 00: DDD
• YY = 02 (OG/IC)
(1) Trunk Route No. (00 – 63)
(2) 3  : Bothway Trunk
• YY = 05 (Release Signal Condition)
(1) Trunk Route No. (00 – 63)
(2) 1  : Release Signal arrives
• YY = 09
(1) Trunk Route No. (00 – 63)
(2) 08: ISDN
• YY = 12 (Number of digits to be received) 
(1) Trunk Route No. (00 – 63)
(2) Number of Digits
0: 1 digit
1: 2 digits
2: 3 digits
3  : 4 digits
555-9677ISDN DTI PBX
555-9677 555-9676CALLING
PA R T Y
START
CM30
A
CM35 
						

							CHAPTER 4 ND-45857 (E)
Pag e 7 8
Revision 3.0
SYSTEM DATA PROGRAMMING
DESCRIPTION DATA
• YY = 18 (Received Digit Conversion)
(1) Trunk Route No. (00 – 63) 
(2) 0/1 : To be provided/Not to be provided 
Assign the destination of DID Call transferred 
when the station is busy/unassigned/no answer.• YY = 00 (No Answer)
• YY = 03 (Busy)
• YY = 06 (Unassigned)
(1) Tenant No. (00 – 63) 
(2) Destination: 
X-XXXX (Station No.)
E000 (SN610 ATTCON) 
EBXXX (Announcement Service: 
Digital Announcement Trunk 
No.)
When the data for CM35 YY = 18 is set to “0” 
(Received Digit Conversion is to be  provided), 
assign the data for interpreting the digits re-
ceived.
Note:If CM35 YYY=143 is set to “1” for Event
Based CCIS, this command must be set.
• Y = 0 (Day Mode)
• Y = 1 (Night Mode) 
(1) X-XXXX: Station No. received. 
(2) X-XXXX: Station/Data Station No. to be 
terminated.
DXX: Change Terminating System to:
D04: DIT
D09: Automated Attendant
D13: TAS
D14: SN610 ATTCON
D16: DISA
BXXX: Mate-Side Trunk No. of Virtual 
Trunk
(B000-B 255)
Note
CM35
CM51
A
CM76
END