NEC Neax2000 Ivs Isdn System Manual

							ND-45857 (E) CHAPTER 4
Page 61
Revision 3.0
CHAPTER 4 SYSTEM DATA PROGRAMMING
1. GENERAL
This chapter describes the programming procedure for providing ISDN to the PBX.
2. SYSTEM DATA PROGRAMMING INFORMATION
In the programming procedure, the meaning of (1), (2) and markings are as follows.
(1) : 1st Data
(2) : 2nd Data
: Initial Data
With the system data clear command (CM00, CM01), the data with this marking is
automatically assigned for each command.
: System Initialization
After entering the data, system reset is required (press SW1 on the MP card).
3. PROGRAMMING PROCEDURE
Assign the system data related to ISDN, according to the following procedure.
For providing the system with a PLO card (PN-CK00), no programming is required.
For details on each command, refer to the Command Manual.
INITIAL 
						

							CHAPTER 4 ND-45857 (E)
Pag e 6 2
Revision 3.0
SYSTEM DATA PROGRAMMING
3.1 Basic Data Assignment for ISDN with PRI
3.1.1 DTI Assignment
DESCRIPTION DATA
Assign a slot number to the DTI card.
(PN-24DTA/24DTA-A).
The slot number assigned must coincide with 
the value set by the SENS switch on the DTI 
card.(1) Slot No. (04-15)
(2) 09: DTI card
Assign ISDN Trunk No. to each channel  num-
ber on the DTI card.
Note:The system allocates time slots to consec-
utive channels from lowest to highest
channel number assigned. To minimize the
number of time slots allocated, assign
trunk numbers to the consecutive channels
on each card. Never skip channels in
CM07.
• YY = 01
(1) XX
 XX
*a *b
*a: Slot No. assigned by CM05
*b: Channel No. of DTI 00-23
(2) Trunk No. (D000-D255)
Trunk number already assigned by CM10 
cannot be used.
Allow second Dial Tone when dialing access 
code assigned by CM20 for ISDN B channel 
route.•Y=2
(1) 04
(2) 0: For ISDN Trunk Route, 2
nd Dial 
Tone is provided.
1: No 2
nd Dial Tone
Assign the necessary functions to the DTI 
card.
After entering the data, set the MB switch on 
the DTI card to UP, and then to DOWN, for DTI 
initialization.• YY=00 (Data Mode)
(1)
(2)Slot No. (04-15) assigned by CM05
0: Based on AT&T Spec.
•
(1)
(2)YY=01 (Frame Configuration)
Slot No. (04-15) assigned by CM05
1 : 24-Multi Frame
•
(1)
(2)YY=02 (Zero Code Suppression [B7])
Slot No. (04-15) assigned by CM05
1 : Not Available (Transparent)(B8ZS)
•
(1)
(2)YY=03
Slot No. (04-15) assigned by CM05
7 : Common Channel Signaling
START
CM05
A
CM07
CMAA
CM48
INITIAL
INITIAL 
						

							ND-45857 (E) CHAPTER 4
Page 63
Revision 3.0
SYSTEM DATA PROGRAMMING
DESCRIPTION DATA
Assign a Trunk Route to each ISDN trunk used 
for Voice channel (B channel), and also to 
signaling channel (D channel). Make a separate 
route for B channels and D channels.
Note:DTI route must be separated from analog
trunk routes.
•
(1)
(2)YY=00
Trunk No. (000-255) assigned by CM07 
YY=01
Trunk Route No. (00-63)
Assign the trunk route data to each ISDN 
incoming trunk used for Voice channel only.
Note:If CM35 YYY=143 is set to “1” for Event
Based CCIS, this command must be set to
“18” (ISDN Indial).
Assign trunk route data to the route number 
assigned by CM30 YY=00.
Note 1:This data should be assigned to the B
channel trunk route.
•
(1)
(2)YY=02 (Day Mode)
YY=03 (Night Mode)
Trunk No. (000-255) assigned by CM07 
YY=01
04: Direct-In Termination
09: Automated Attendant
13: TAS
14: Termination to ATTCON
16: DISA
18: ISDN Indial
•
(1)
(2)YY=00 (Kind of Trunk Route)
B channel Route No. (00-63)
00: ISDN Trunk
(1)
(2)D channel Route No. (00-63)
15 : Not used
• YY=02 (Call Direction)
(1) B channel Route No. (00-63)
(2) 3 : Bothway Trunk
Note 1
• YY=04 (Answer Signal from Distant 
Office)
(1) B channel Route No. (00-63)
(2) 2: Answer signal arrives (ISDN Trunk)
(1) D channel Route No. (00-63)
(2) 7 : Not used
CM30
B
CM35
A 
						

							CHAPTER 4 ND-45857 (E)
Pag e 6 4
Revision 3.0
SYSTEM DATA PROGRAMMING
DESCRIPTION DATA
Note 1:This data should be assigned to the B
channel trunk route.
Note 2:This data should be assigned to both B
channel trunk route and D channel trunk
ro ut e.
• YY=05 (Release Signal from Distant 
Office)
(1)
(2)B channel/D channel Route No. (00-63)
1 : Release signal arrives
Note 2
• YY=09 (Incoming Connection Signaling)
(1) B channel Route No. (00-63)
(2) 08: ISDN
(1) D channel Route No. (00-63)
(2) 15 : Not used
• YY=11 (Toll Restriction)
(1) B channel Route No. (00-63)
(2) 0/3 : To be provided/Not to be provided
Note 1
Specify the number of digits to be received on  • YY = 12
DID. (1) B channel Route No. (00-63)
Note:If CM35 YYY=143 is set to “1” for Event
Based CCIS, the number of digits received
on DID must be assigned.(2) 0 : 1 digit
1 : 2 digits
2 : 3 digits
3 : 4 digits
• YY = 14 (SMDR for Outgoing Call)
(1) B channel Route No. (00 – 63)
(2) 0/1 : Not to be provided/To be provided
Note 1
• YY = 15 (Kind of Call Termination Indica-
tor Key/Lamp on ATT)
(1) B channel Route No. (00 – 63)
(2) 00 – 07 (C.O. Incoming 0 – 7)
• YY = 16 (Hooking Signal Sending to Out-
side)
(1) B channel Route No. (00 – 63)
(2) 0: Not sending
CM35
C
B 
						

							ND-45857 (E) CHAPTER 4
Page 65
Revision 3.0
SYSTEM DATA PROGRAMMING
DESCRIPTION DATA
•
(1)
(2)
•
(1)
(2)YY=18 (Digit conversion on DID call)
Trunk Route No. (00-63)
0 : To provide
1  : Not provided
YY=19
Trunk Route No. (00-63)
0:
1: Programmable PAD 
2: (See CM42)
3:
4:
5: Fixed PAD
6: (See left table)
7:
Note
T/R: Transmitter PAD/Receiver PAD
+: Gain
Note:This data should be assigned to the B
channel trunk route.
•
(1)
(2)YY=28 (Outgoing Trunk Queuing)
Trunk Route No. (00-63)
0: Restricted
For D channel trunk route, no data setting 
is required
Specify which number is adopted for corre-
sponding of virtual trunks between the offices, 
either sub-address number or ISDN Indial di-
aled-in digits.•
(1)
(2)
•
(1)
(2)YY=39 (Trunk release by detection of 
reversal of tip and ring)
Trunk Route No. (00-63)
1 : To be released
Note
YYY=143
Trunk Route No. (00-63)
0 : By sub-address
1 : By dialed in digits
CM35
D
C
CONNECTION 
PATTERNSPAD DATA OF DTI [dB]
DATA
=4 (T/R)DATA
=5 (T/R)DATA
=6 (T/R)DATA
=7 (T/R)
Station – DTI 3/8 3/3 3/3 3/8
Tone – DTI 0/0 0/0 0/0 0/0
COT/LDT – DTI 0/0 0/0 0/0 0/0
ODT – DTI +3/3 0/0 0/0 +3/3
DTI –DTI 0/6 0/0 0/6 0/0 
						

							CHAPTER 4 ND-45857 (E)
Pag e 6 6
Revision 3.0
SYSTEM DATA PROGRAMMING
DESCRIPTION DATA
When using the programmable PAD (CM35 
YY = 19, 2nd Data = 0-3), assign the PAD 
data.(1)
(2)50-65
00-15
T/R: Transmitter PAD/Receiver PAD
+: GainCM42
D
END
PAD DATA PATTERNS
CONNECTING
PATTERNS CM35 YY=19
2ND DATA=0CM35 YY=19
2ND DATA=1CM35 YY=19
2ND DATA=2CM35 YY=19
2ND DATA=3
50
6550 54 58 62 STA/TONE-DTI
51 55 59 63 COT/LDT-DTI
52 56 60 64 ODT-DTI
53 57 61 65 DTI-DTI
1ST
DATA
~
PAT T E R N
PAD DATA OF DTI (T/R) [dB] REMARKS
00
1500 0/0
01 2/2
02 3/3
03 0/6
04 3/8
05 +3/3
06 6/6
07 8/8
08
15Not Used
PAT T E R N
2ND DATA
~
~ 
						

							ND-45857 (E) CHAPTER 4
Page 67
Revision 3.0
SYSTEM DATA PROGRAMMING
• For originating calls to the ISDN network, assign the following data.
DESCRIPTION DATA
Assign ISDN access code to each trunk route
assigned by CM30 YY=00.
Note:LCR can be used with ISDN-PRI. Refer to
Feature Programming Manual.
• Y=0-3 (Numbering Plan Group 0-3)
(1) X-XXX (Access code)
(2) 100-163: Trunk Route No. (00-63)
Specify the timing start when making an ISDN 
call from SN610 ATTCON.(1) 403
(2) 0/1 : Not Available/Available
Specify the timing start when making an ISDN 
call from a Single Line Telephone (PB/DP), 
Multiline Terminal or SN610 ATTCON, if 
required.•Y=0
(1) 50
(2) 03-14: 3 sec.-14 sec.
If no data is set, the timing start is not 
effective.
(Dialing terminated by entering #.) 
Recommended setting is 05 (5 seconds).
Note:A # or timing start is used for outgoing ISDN calls when LCR is not invoked.
Example:1-214-555-1212 is dialed from a Multiline Terminal. The PBX will access a bearer chan-
nel and ship the digits only after the timing start timer has expired or # is dialed by the caller. The
# sign tells the PBX that dialing is completed.
END
START
CM20
CM08
CM41 
						

							CHAPTER 4 ND-45857 (E)
Pag e 6 8
Revision 3.0
SYSTEM DATA PROGRAMMING
• When providing Tandem Connection (Tie Line (OD/DTI) to ISDN — ISDN to Tie Line (OD/DTI)), do the
following programming.
• When providing Tandem Connection (ISDN to CCIS — CCIS to ISDN), do the following programming.
DESCRIPTION DATA
Specify the combination of Trunk Routes 
allowing the tandem connection.(1) XX  XX
00-63 (Incoming Trunk Route)
00-63 (Outgoing Trunk Route)
(2) 0/1  : Allowed/Restricted 
Specify the timing start when making an ISDN 
call from a station (PB/DP telephone D
term) or 
Attendant Console for the Tandem Connection. •Y = 0
(1) 57
(2) 03 – 14: 3 sec. – 14 sec.
Note:By using this command, an ISDN call is available even if “#” is not dialed.
Note:This command is effective for dialing a called number (When dialing a called party subaddress,
this command is not effective).
Note:When the default setting is “NONE”, the timing start is not effective.
DESCRIPTION DATA
Specify the combination of Trunk Routes 
allowing the tandem connection.(1) XXXX
00-63 (Incoming Trunk Route)
00-63 (Outgoing Trunk Route)
(2) 0/1 : Allowed/Restricted
Specify whether the Calling Party Number 
(CPN) sent from ISDN is sent to the CCIS net-
work.(1)
(2)374
0/1 : Available/Not Available
START
END
CM36
CM41
CM36
CM08 START
END 
						

							ND-45857 (E) CHAPTER 4
Addendum-001 Page 69
AUGUST, 1998 Revision 3.1
SYSTEM DATA PROGRAMMING
3.1.2 DCH Assignment
DESCRIPTION DATA
Assign a slot number to the DCH card 
(PN-SC01).
The slot number assigned must coincide with 
the value set by the SENS switch on the 
PN-SC01 card.(1) Slot No. (04 – 15)
(2) 12: PN-SC01 card 
Assign the ISDN protocol type to a slot number 
assigned by CM05.•
(1)
(2)YY=06
Slot No. of DCH (04-15) assigned by 
CM05
20:  AT&T (No. 4, No. 5 ESS)
21:  NTI (DMS 100, 250)
28:  National ISDN 2 (NI-2)
Assign the DCH Number to the Slot Number of 
DCH assigned by CM05.• YY = 08
(1) DCH No.
0 – 4: When using PN-24DTA/24DTA-A
(2) XX: Slot No. assigned by CM05
Execute CM35 YY = 90 for Voice Route 
B channels and D channel Route.• YY = 90 (Assignment of DTI route for 
ISDN)
(1) Route No. (00 – 63)
(2) 3: ISDN-Primary Rate Interface
Assign the DCH No. to the ISDN trunk route 
assigned by CM30 YY = 00.• YY = 93 (Assignment of D Channel 
Handler)
(1) Route No. (00 – 63)
(2) DCH No. assigned by CM06
00 – 04: for PN-24DTA/24DTA-A
Assign CIC (Circuit Identification Code) No. to 
each ISDN trunk used for voice channel only.• YY = 07
(1) Trunk No. (000 – 255) assigned by CM07 
YY = 01
(2) CIC No. (000 – 029)
Assign the trunk number assigned by CM07  
YY = 01 to each DCH Number for providing  
D Channel path between DTI and DCH.• YY = 00
(1) DCH No. assigned by CM06
0 – 4: for PN-24DTA/24DTA-A
(2) Trunk No. (000 – 255) assigned by CM07 
YY = 01
START
CM05
CM06
CM30
CMA9
CM35
END
CMAA
INITIAL
INITIAL
INITIAL 
						

							CHAPTER 4 ND-45857 (E)
Page 70 Addendum-001
Revision 3.1 AUGUST, 1998
SYSTEM DATA PROGRAMMING
3.2 Basic Data Assignment for ISDN with BRI
3.2.1 BRI 
Assignment
DESCRIPTION DATA
Assign a slot number to the BRI card. 
The slot number assigned must coincide with 
the value set by the SENS switch on the BRI 
card. 
Specify ISDN protocol type to a slot number 
assigned by CM05.
Assign ISDN Trunk No. to each Channel No. of 
BRI Trunk. 
Assign Trunk Route to each ISDN trunk used 
for Voice channel (B channel).  
Note:BRI route must be separated from analog
trunk routes.  
Assign the trunk route data to each ISDN 
incoming trunk used for Voice channel only.  
Note:If CM35 YYY=143 is set to “1” for Event
Based CCIS, this command must be set to
“18” (ISDN Indial).
Note:
The programming example for BRI
trunks is in Chapter 4 on Pages 128
and 129
.
(1)   Slot No. (04-15)
(2)   10: BRI card
•  YY=06
(1)   Slot No. (04-15) assigned by CM05
(2)   27: USA NI-1
•  YY=02
(1) XX
  XX
*a *b
*a: Slot No. assigned by CM05
*b: Channel No. (00/01/02/03)
(2)   Trunk No. (D000-D255)  Trunk No. 
already assigned by CM10 can not to be 
used.
•  YY=00
(1)   Trunk No. (000-255) assigned by CM07 
YY=01
(2)   Trunk Route No. (00-63)
•   YY=02 (Day Mode)
YY=03 (Night Mode)
(1)   Trunk No. (000-255) assigned by CM07 
YY=01
(2) 18: ISDN Indial
START
CM05
CM07
A
CMAA
CM30
INITIAL
INITIAL