NEC Neax2000 Ivs Isdn System Manual

							ND-45857 (E) CHAPTER 4
Addendum-001 Page 137
AUGUST, 1998 Revision 3.1
SYSTEM DATA PROGRAMMING
DESCRIPTION DATA
Area Code + Local Office Code • YY=05
00 > 214555
Last 4 digits of telephone no. + 4 digit SPID • YY=30
040 > 62040101
041 > 62050101
050 > 62060101
051 > 62070101
Set as ISDN trunk route.
Answer signal arrives.
Incoming connection signaling.
Hooking signal sending to outside not 
provided.
Enable digit conversion.
Disable trunk queuing outgoing.
Assign as BRI trunk route.•
•
•
•
•
•
•YY=00
10 > 00
11 > 00
YY=04
10 > 2
11 > 2
YY=09
10 > 08
11 > 08
YY=16
10 > 0
11 > 0
YY=18
10 > 0
11 > 0
YY=28
10 > 0
11 > 0
YY=90
10 > 2
11 > 2
Terminate BRI trunks to station for testing. • Y=0 & Y=1
6204 > Sta. no.
6205 > Sta. no.
6206 > Sta. no.
6207 > Sta. no.CM50
CMAC
A
CM35
CM76
END 
						

							CHAPTER 4 ND-45857 (E)
Page 138 Addendum-001
Revision 3.1 AUGUST, 1998
SYSTEM DATA PROGRAMMING
BRI Trunks in PBX A are:
Circuit 1: B1  (214) 555-6868
B2   (214) 555-6869
Circuit 2: B1  (214) 555-6870
B2  (214) 555-6871
Note:You must have this information prior to programming E-CCIS.
• Home-Side Trunk Programming
DESCRIPTION DATA
Assign Home-Side trunks to even numbered 
addresses.• YY=05
3200 > D030
3202 > D031
3204 > D032
3206 > D033
Assign trunks to trunk routes. • YY=00
030 > 30
031 > 30
032 > 30
033 > 31
Assign as Tie Line routes. • YY=00
30 > 04
31 > 04
Set route as Dial Pulse.
Answer signal arrives.
Incoming connection signaling.
Seize trunks by lowest numbered trunk.
Assign as CCIS.•
•
•
•
•YY=01
30 > 2
31 > 2
YY=04
30 > 2
31 > 2
YY=09
30 > 06
31 > 06
YY=83
30 > 0
YY=90
0 > 0
31 > 0CM07 START
A
CM30
CM35 
						

							ND-45857 (E) CHAPTER 4
Addendum-001 Page 139
AUGUST, 1998 Revision 3.1
SYSTEM DATA PROGRAMMING
DESCRIPTION DATA
Assign CCH Channel No.
Assign as E-CCIS route.•
•YY=91
30 > 0
31 > 0
YYY=135
30 > 0
31 > 0
Assign CIC no. • YY=35
030 > 001
031 > 002
032 > 003CM35
CM30
A
END 
						

							CHAPTER 4 ND-45857 (E)
Page 140 Addendum-001
Revision 3.1 AUGUST, 1998
SYSTEM DATA PROGRAMMING
• Mate-Side Trunk Programming
DESCRIPTION DATA
Assign Mate-Side trunks to odd numbered 
addresses.• YY=05
3201 > D040
3203 > D041
3205 > D042
3207 > D043
Assign trunks to trunk routes.
Assign last 4 digits of telephone number in 
PBX A.•
•YY=00
040 > 40
041 > 41
042 > 42
043 > 43
YY=19 
040 > 6868
041 > 6869
042 > 6870
043 > 6871
Assign as Tie Line routes.
Assign abbreviated codes to terminate call to 
PBX A.
Note:Terminating number and its memory allo-
cation are assigned by CM 71 and CM 72.
Release virtual tie line if there are no calls for a 
predetermined time.
Assign as E-CCIS route.•
•
•
•YY=00
40 > 04
41 > 04
42 > 04
43 > 04
YY=40
40 > 00
41 > 01
42 > 02
43 > 03
YYY=127
40 > 0
41 > 0
42 > 0
43 > 0
YYY=135
40 > 0
41 > 0
42 > 0
43 > 0
CM07 START
CM30
CM35
END 
						

							ND-45857 (E) CHAPTER 4
Addendum-001 Page 141
AUGUST, 1998 Revision 3.1
SYSTEM DATA PROGRAMMING
3.10.2 Program Termination for Incoming E-CCIS Calls
3.10.3 Program Access Code/Terminating Number Assignment for Outgoing E-CCIS Calls
3.10.4 Program Release Timer for Virtual Tie Lines (Home-Side & Mate-Side Trunks)DESCRIPTION DATA
Convert received digits to Mate-Side trunks. • Y=0 & Y=1
6204 > B040
6205 > B041
6206 > B042
6207 > B043
DESCRIPTION DATA
Allocate memory to store the terminating num-
bers of PBX B
Note:In the stored number a trunk route access
code must be used. E-CCIS will not work
if an LCR access code is used.
•
•66 > 100004
100 > 80,2145556868
101 > 80,2145556869
102 > 80,2145556870
103 > 81,2145556871
DESCRIPTION DATA
Release timer for voice channels
Release timer for CCH channel•
•Y=0
87 > 04
Y=0
89 > 08
CM76 START
END
CM71 START
END
CM72
CM41 START
END 
						

							CHAPTER 4 ND-45857 (E)
Page 142 Addendum-001
Revision 3.1 AUGUST, 1998
SYSTEM DATA PROGRAMMING
3.10.5 CCH Data Assignment:
Sense Wheel for PN-SC00 is set to 06.
Originating Point Code for PBX  B is 00002.
3.10.6 Alternative ISDN Route Assignment
To provide an ISDN line as an alternative route when the call can not be connected through the virtual tie line,
do the programming for Least Cost Routing. Refer to the NEAX2000 IVS Feature Programming Manual.
For the call through the alternative ISDN route, the called number which is dialed by the caller is set to the sub-
address.
DESCRIPTION DATA
Assign CCH card.
• 06 > 11
Assign CCH channel no. to CCH card.
•YY=07
0 > 06
Provide the PBX with CCIS.
•53 > 0
Assign trunk to be used as CCH channel.
Assign Originating Point Code.
Assign Destination Point Code.
Assign ACM Signal Waiting Timer.
Assign E-CCIS for the CCH channel.•
•
•
•
•YY=00 
0 > 043
YY=01
0 > 00002
YY=02
0 > 00001
YY=10
0 > 14
YY=27
0 > 0
Assign CCH channel to which a signaling mes-
sage is transferred according to the Destination 
Point Code received.)• 0 > 00001CM05 START
CM09
CMA8
CM06
CMA7
END 
						

							ND -4 5857 ( E)  CHAPTER 5
CHAPTER 5  INSTA LLA TIO N T E S T 
						

							CHAPTER 5 ND-45857 (E)
Pag e 1 44
Revision 3.0
INSTALLATION TEST
Table 5-1  Alarm Indications on the PN-24DTA Card
LEDLED INDICATION FAULT
NORMAL FAULT CAUSE ACTION
RUNFlash 
(120IPM)OffDTI Trunk data is not 
correctly assigned.1.Reset the MB switch.
(Down®UP®Down)
2.Confirm the program data 
(CM05, CM07 YY = 01)
CRC Off OnBit Error Rate exceeds the 
predetermined value.Check the transmission line and external 
equipment.
PCM Off OnNo PCM signals arrive from 
the distant office.1.Check to see if the DTI cable is cor-
rectly connected.   
2.Plug and unplug the DTI cards. Repeat 
this two or three times.
FRM Off OnFrame Alignment signals 
from the distant office 
cannot be received.Check the transmission line and external 
equipment.
RMT Off OnFrame Alignment signals 
cannot be sent to the 
opposite PBX.Replace the DTI card.
AIS Off OnOpposite PBX is in the loop-
back test.Check the opposite DTI card. 
						

							ND-45857 (E) CHAPTER 5
Page 145
Revision 3.0
INSTALLATION TEST
3.2 PLO Operation Test
The following tests should be performed to confirm the PLO operation’s normality.
• Clock Signal Generation Test
• Clock Signal Synchronization Test To be performed when the PBX is a slave office.
• Interoffice Synchronization Test
3.2.1 Clock Signal Generation Test
This test checks to see if the PLO keeps generating clock signals at the frequency of the previous master clock,
when the external clock signal from the master office and sub-master office have stopped.
To perform this test, an “In Service” transmission line is required.
STEP 1: On all the DTI cards mounted in the PIM0, set the SW-1 and SW-2 to “OFF” to stop the external
clock signal input.
– The CLKIN lamp on the MP card goes out.
STEP 2: Originate an outgoing call via DTI.
STEP 3: After an outgoing connection via DTI has been established, confirm interoffice synchronization and
speech quality with the following procedure.
On the DTMF telephone set, keep pressing any dial button.
Check to see if noise is periodically occurring with the DTMF signals
coming from the calling station in the opposite office.
Perform the above test again in the opposite direction.
STEP 4: On all the DTI cards mounted in the PIM0, restore the SW-1 and SW-2 as the state before testing to
input the external clock signals.
– The CLKIN lamp on the MP card lights.
If noise is periodically occurring, replace the MP card after checking the switch settings on the MP card,
and perform the above test again.
1
2
3 
						

							CHAPTER 5 ND-45857 (E)
Pag e 1 46
Revision 3.0
INSTALLATION TEST
3.2.2 Clock Signal Synchronization Test
This test checks to see if the PLO keeps synchronizing with the external clock signals, when the external clock
signals from the master/sub-master office has input again after it has stopped once.
To perform this test, an “In Service” transmission line is required.
(1) When providing one clock supply route (from a master office)
STEP 1: On the DTI card extracting clock signals (DTI0), set the SW-1 and SW-2 to “OFF” to stop the exter-
nal clock signal input.
– The CLKIN lamp on the MP card goes out.
STEP 2: Originate an outgoing call via DTI.
STEP 3: After an outgoing connection via DTI has been established, confirm interoffice synchronization and
speech quality with the following procedure.
On the DTMF telephone set, keep pressing any dial button.
Check to see if noise is periodically occurring with the DTMF signals
coming from the calling station in the opposite office.
Perform the above test again in the opposite direction.
STEP 4: On the DTI card (DTI0), restore the SW-1 and SW-2 as the state before testing to input the external
clock signals.
– The CLKIN lamp on the MP card lights.
STEP 5: Originate an outgoing call via DTI.
STEP 6: After an outgoing connection via DTI has been established, confirm interoffice synchronization and
speech quality with the procedure  –  shown in STEP 3.
If noise is periodically occurring, replace the MP card after checking the switch settings on the MP card,
and perform the above test again.
1
2
3
13