NEC Neax2000 Ivs Isdn System Manual

							ND-45857 (E) CHAPTER 4
Page 117
Revision 3.0
SYSTEM DATA PROGRAMMING
DESCRIPTION DATA
• YY=12 (Number of digits to be received)
(1) Trunk Route No. (00-63)
(2) Number of Digits
0: 1 digit 
1: 2 digits 
2: 3 digits 
3 : 4 digits
• YY=18 (Received Digit Conversion)
(1) Trunk Route No. (00-63)
(2) 0/1 : To be provided/Not to be provided
Assign the destination of DID Call transferred 
when the station is busy/unassigned/not an-
swer.• YY=00 (No Answer)
• YY=03 (Busy)
• YY=06 (Unassigned)
(1) Tenant No. (00-63)
(2) Destination: 
X-XXXX(Station No.) 
E000 (SN610 ATTCON) 
EBXXX (Announcement Service:
Digital Announcement Trunk 
Circuit No.)
When the data for CM35 YY=18 is set to “0” 
(Received Digit Conversion is to be provided), 
assign the data for interpreting the digits re-
ceived.• Y=0 (Day Mode)
• Y=1 (Night Mode)
(1) X-XXXX: Station Number received
(2) X-XXXX: ISDN Terminal No.CM35
A
CM51
CM76
END 
						

							CHAPTER 4  ND -4 5857 ( E)
S YST EM  DATA P RO G RA MMING
ISDN
ISDN  Te rm in a l
IL C   DTI
(O ffice  N o.)
-4 0 0
(C alle d  PartyS ub ad dre ss =
C M 08
END 
						

							ND -4 5857 ( E)  CHAPTER 4
SYSTEM  DATA  P R O GRAMM ING
ISDN
I S DN  T e rm in al
IL C   DTI
C M 30
END 
						

							CHAPTER 4  ND -4 5857 ( E)
S YST EM  DATA P RO G RA MMING
IS D N
ISDN  Te rm in a l
ILC   DTI
ISDN  Te rm in a l
ILC
IS DN  T e rm in al N o.  4 1 0 d ia ls 4 00  to  re ach 
						

							ND-45857 (E) CHAPTER 4
Addendum-001 Page 121
AUGUST, 1998 Revision 3.1
SYSTEM DATA PROGRAMMING
3.6.5 Group Call Assignment
(1) ISDN Indial
When receiving an ISDN Circuit Number as the ISDN Indial Number or when converting an ISDN Indial
Number to an ISDN Circuit Number by CM76, the system makes the connection with all ISDN Terminals
or Terminal Adapters (TA) on the same bus (2B + D).
In addition to the programming of Section 3.5, do the following programming.
DESCRIPTION DATA
Assign the data for DID to the Trunk Numbers 
assigned by CM07.• YY=02 (Terminating System in Day Mode)
• YY=03 (Terminating System in Night 
Mode)
(1) Trunk No. (000-255) assigned by CM07 
YY=01
(2) 18: ISDN Indial
Assign the data for DID to the Trunk Routes 
assigned by CM30.• YY=00 (Kind of Trunk)
(1) Trunk Route No. (00-63)
(2) 00:DID
• YY=02 (OG/IC)
(1) Trunk Route No. (00-63)
(2) 3 : Bothway Trunk
• YY=05 (Release Signal Condition)
(1) Trunk Route No. (00-63)
(2) 1 : Release Signal arrives
• YY=09
(1) Trunk Route No. (00-63)
(2) 08: ISDN
ISDN
ISDN Terminal
No. 401ISDN Terminal
No. 400ISDN Circuit
Station No. 300
ILCConverting “7715” to ”300”
DTI
PBX
214-555-7715
(ISDN Indial No.)

CM30
A
CM35 START 
						

							CHAPTER 4 ND-45857 (E)
Pag e 1 22
Revision 3.0
SYSTEM DATA PROGRAMMING
DESCRIPTION DATA
• YY=12 (Number of digits to be received)
(1) Trunk Route No. (00-63)
(2) Number of Digits
0: 1 digit
1: 2 digits 
2: 3 digits 
3 : 4 digits
• YY=18 (Received Digit Conversion)
(1) Trunk Route No. (00-63)
(2) 0/1 : To be provided/Not to be provided
Assign the destination of DID Call transferred 
when the station is busy/unassigned/not an-
swer.• YY=00 (No Answer)
• YY=03 (Busy)
• YY=06 (Unassigned)
(1) Tenant No. (00-63)
(2) Destination: 
X-XXXX (Station No.) 
E000 (SN610 ATTCON) 
EBXXX (Announcement Service: Digital 
Announcement Trunk Circuit 
No.)
When the data for CM35 YY=18 is set to “0” 
(Received Digit Conversion is to be provided), 
assign the data for interpreting the digits re-
ceived.• Y=0 (Day Mode)
• Y=1 (Night Mode)
(1) X-XXXX: Station Number received.
(2) X-XXXX: ISDN Circuit Station No.CM35
A
CM51
CM76
END 
						

							ND -4 5857 ( E)  CHAPTER 4
SYSTEM  DATA  P R O GRAMM ING
ISDN
I S DN  T e rm in al
IL C   DTI
(O ffic e  N o.)
3 0 0 #
(C alle d  P artyS ub ad dres s)
C M 08
END 
						

							CHAPTER 4  ND -4 5857 ( E)
S YST EM  DATA P RO G RA MMING
IS DN
ISDN  Te rm in al
IL C   DTI
CM 30
END 
						

							ND -4 5857 ( E)  CHAPTER 4
SYSTEM  DATA  P R O GRAMM ING
I S DN
IS DN  T er min al
IL C   DTI
IS DN  T er min al
IL C 
						

							CHAPTER 4 ND-45857 (E)
Pag e 1 26
Revision 3.0
SYSTEM DATA PROGRAMMING
3.7 Data Assignment for Event Based CCIS
This section describes the programming procedure to provide the system with Event Based CCIS.
As for the voice communication service feature programming on No. 7 CCIS, refer to the No. 7 CCIS System
Manual.
3.7.1 Outline of Data Programming for Event Based CCIS
For the Event Based CCIS, the Virtual Trunks which are used as No. 7 CCIS trunks, and the existing CCH card
must be assigned by system data programming to activate No. 7 CCIS link (virtual tie line connection) on an
ISDN network.
Virtual Trunk:
The Virtual Trunk consists of a Home-Side Trunk and a Mate-Side Trunk. The Home-Side Trunk is con-
nected to the station side, and the Mate-Side Trunk is connected to network side of the PBX virtually.
The virtual trunks do not exist actually, but are handled as No. 7 CCIS trunk by the system, for system data.
ISDN sub-address programmed to the virtual trunk is used to establish a CCIS link and individual voice
link.
CCH Card:
The CCH card is used to handle the common channel signaling.
For Event Based CCIS, the system data for CCH card should be programmed according to the same method
for regular No. 7 CCIS programming.
DTI/BRI Card:
The system uses the same interface trunk (DTI/BRI card) for regular ISDN connection and for the virtual
tie line connection on the Event Based CCIS.
For the DTI/BRI card, regular programming as the interface trunk for ISDN network should be assigned.