NEC Neax2000 Ivs Isdn System Manual

							ND-45857 (E) CHAPTER 4
Page 99
Revision 3.0
SYSTEM DATA PROGRAMMING
DESCRIPTION DATA
Specify the conditions for adding a Check Code 
to each Authorization Code.
Check Code consists of 2 digits:
1st and 2nd Check Code are generated by the 
AP according to the conditions specified by Y 
= 0 and Y = 1.
Authorization Code:
X
1 X2 X3 X4 X5 X6 X7 X8C1 C2 
ID Code programmed Check Code
X: Significant Digit for Check Code• Y = 0 (Designation of Significant digit for 
Check Code)
(1) 0: For 1st Check Code
1: For 2nd Check Code
(2) 00 X
X: Significant digit designation
*a *b
*a: 1st – 4th digit (0 – F)
*b: 5th – 8th digit (0 – F)
(See left column)
If no Check Code is required, set data = 0000 for 
both 1st and 2nd Check Code.
• Y = 1 (Setting of Check Sum Data for gen-
erating Check Code)
(1) 0: For 1st Check Code
1: For 2nd Check Code
(2) 0 – 9: Check Sum Data (Enter desired val-
ue)
CMD5
C
B
DIGIT
DATAX1X2X3X4
X5X6X7X8
0
1
2
3
4
5
6
7
8
9
A
B
C
D
E
FNo Check Code
X
X
X X
X
X X
XX–
XXX
X
X
X
X
X
X
X
X X
X
X
XX
X
X
XX
X
X
X 
						

							CHAPTER 4 ND-45857 (E)
Pag e 1 00
Revision 3.0
SYSTEM DATA PROGRAMMING
DESCRIPTION DATA
Set the Authorization Code and its temporary 
Class of Service.
By entering the Authorization Code, the Check 
Code will be display on the MAT or CAT.•Y = 3
(1) X – X...X: Authorization Code (Max. num-
ber of digits specified by CM42-11.)
(2) A (Single Digit): In case of A = 0, 1 or 9 
ABBCCDDEE (9 digits): In case of A = 2
• Temporary Class of Service
A: Type of Temporary Class of Service
0: Unrestricted
1: Fully Restricted
2: As per BBCCDDEE
9: Delete of the ID Code
BB: Trunk Restriction Class 
(01 – 08) specified by CM35
YY = 51 – 68.
CC: Service Restriction 
Class (A) (01 – 15)
DD: Service Restriction 
Class (B) (01 – 15)
EE: Service Restriction
 Class(C) (01 – 15)(See left column)
Assign the number of digits to be received on 
DID.• YY = 12
(1) Trunk Route No. (00 – 63)
(2) 0: 1 digit
1: 2 digits
2: 3 digits
3 : 4 digits
Assign the data for digit conversion on DID 
calls to the Route No. assigned by CM30 
YY = 00 when providing DISA to the DID 
call.• YY = 18
(1) Trunk Route No. (00 – 63)
(2) 0/1 : To be provided/Not to be providedCMD5
D
C
CM35
As per CM15 
						

							ND-45857 (E) CHAPTER 4
Page 101
Revision 3.0
SYSTEM DATA PROGRAMMING
DESCRIPTION DATA
When the data for CM35 YY = 18 is set to 0, as-
sign the data for converting the received digit(s) 
to DISA.• Y = 0 (Day Mode)
• Y = 1 (Night Mode)
(1) X-XXXX:Station No. received
(2) D16:DISA
Specify the maximum number of digits for ID 
Codes on DISA.
Note:The same number of digits must be as-
signed by CM42-11 and CM42-13.
(1) 11, 13
(2) 01 – 10 (Maximum Number of Digits).If 
Check Code is provided, the maximum 
number of digits is limited to eight (8).If no 
data is set, 10 digits will be applied.
CM76
D
CM42
END 
						

							CHAPTER 4 ND-45857 (E)
Pag e 1 02
Revision 3.0
SYSTEM DATA PROGRAMMING
To access the Digital Announcement Trunk (PN-2DATA) via DISA, add the following programming.
DESCRIPTION DATA
Assign a Digital Announcement Trunk Circuit 
No. to the required LEN.
Note:The Digital Announcement Trunk Circuit
No. must be assigned to the first LEN
(Level 0) and/or the third LEN (Level 2) of
each LT slot.
(1) LEN (0000-0511)
(2) EB000 – EB127: Digital Announcement 
Trunk Circuit No.
For PIM0/1: EB000 – EB031
For PIM2/3: EB032 – EB063
For PIM4/5: EB064 – EB095
For PIM6/7: EB096 – EB127
Assign the Class of Service for Digital An-
nouncement Trunk access to the required ID 
Code Serial No., when providing DISA without 
an Application Processor (PN-AP01).• CM2A Y = 7
(1) XX: ID Code Serial No. (00 – 07) assigned 
by CM2A Y = 5
(2) XX
 XX
*a *b
*a: Service Rest. Class (A) (00 – 15)
*b: Service Rest. Class (B) (00 – 15)
• CM15 YY = 33
(1) Service Rest. Class (A) (00 – 15) assigned 
by CM2A Y = 7
(2) 1 : Allowed
Assign the Class of Service for Digital An-
nouncement Trunk access to the required ID 
Code Serial No., when providing DISA with an 
Application Processor (PN-AP01).• CMD5 Y = 3
(1) X-X---X: ID Code (Max. Number of digits 
specified by CM42-13)
(2) 201 XX
0000
*a
*a: Service Rest. Class (A) (00 – 15)
• CM15 YY = 33
(1) Service Rest. Class (A) (00 – 15) assigned 
by CMD5 Y = 3
(2) 1 : Allowed
To record and replay a message from an outside 
user, assign the Digital Announcement Trunk 
access code, respectively.• Y = 0 – 3 (Numbering plan Group 0 – 3)
(1) X-XXX: Access Code
(2) A00: Record
01: Replay
START
CM10
CM2A
CMD5
CM15
CM15
CM20
END 
						

							ND-45857 (E) CHAPTER 4
Page 103
Revision 3.0
SYSTEM DATA PROGRAMMING
3.4 ISDN PRI Call By Call Service Selection
General
1500 Series Software enhanced ISDN PRI by providing Call By Call Services Selection. the Call By Call en-
hancements require two new components for implementation: 
• D Channel Handler (DCH) firmware upgrade to revision CB1.15
• 1500 Series CD 2.05 or higher including proper Serial ID key software
The separate sections have been implemented in LCR programming for the CBC enhancement.
• Called Number Type
• Network ID Type
• Binary Facility Codes
• Feature/Service
Available Services
The following Binary Facility Code can be sent to the ISDN network when the called party number is flagged
as a Service. Services and features are selected by the ISDN subscriber at the time the ISDN is ordered. The
PBX must be programmed to match the services and features provided by the ISDN provider.
AT&T Northern Telecom
SDN Private
Megacom InWATS
Megacom 800 OutWATS
Accunet Foreign Exchange
International 800 Tie Trunk
AT&T MultiQuest
Call By Call LCR Programming
The following programming steps is an example of a long-distance call placed to any area code that begins with
a 2 and that call is flagged as AT&T Megacom.
CM8A405 - 12(dialed #) = 001 (go to route pattern 001)
CM8A001 - 1 (1
st choice)=00010 (use LCR pattern 000 + trk route 10)
CM 855 - 12 = 11 (maximum number of digits dialed)
CM 8A500 - 157 =  02 (Kind of called party = National) (dialed number is 10-digit NANP, select National)
CM 8A500 - 158 =  01 (Called party Number Plan ID = ISDN / Telephony Numbering Plan
CM 8A500 - 159 ~ 161 are not used for this call.
CM 8A500 - 162 = 1 (Service)
CM 8A500 - 163 =  03 (Megacom)
CM 8A500 - 164 is not required for this call.  
						

							CHAPTER 4 ND-45857 (E)
Pag e 1 04
Revision 3.0
SYSTEM DATA PROGRAMMING
The next example details a local 7 digit call and will not used a Binary Facility Code.
CM8A405 - 2 (dialed number) = 001 (go to route pattern 000)
CM8A000 - 1 (1
st choice)=00210 (use LCR pattern 002 + trk route 10)
CM 855 - 2 = 7 (maximum number of digits dialed)
CM 8A502 - 157 =  04 (Kind of called party = Local) (dialed number is 7-digit NANP, select Local)
CM 8A502 - 158 =  01 (Called party Number Plan ID = ISDN / Telephony Numbering Plan
CM 8A502 - 159 ~ 161 are not used for this call.
CM 8A502 - 162 = 1 (Service)
CM 8A502 - 163 =  NONE (not sending)
CM 8A502 - 164 is not required for this call. 
Note:These examples are provided to demonstrate the required programming. Always verify with the ISDN provider as to
how local calls should be handled.
Features
Carrier Identification Codes (CIC)
In ISDN terms placing a long-distance call using the equal access carrier code is a feature. There are times when,
depending upon the type of service provider (LEC or IEX), the PBX must contain the following programming
to complete a long-distance call by using CIC numbers.
Currently all CIC numbers are three digits in length preceded by a 10. Example: To dial AT&T a user dials
10288 + the long-distance number. The PBX must route the call based on 10288 or a portion of that number.
ISDN complicates this process by identifying each CIC at the PBX level.
For example: Without ISDN the PBX is able to simply outpulse 10288 and the public network would provide
connection to AT&T. With ISDN used for routing equal access calls, the PBX must translate the 10288 in its
entirety and provide the network with four pieces of information as described below. The implementation of this
feature is further complicated by the fact that this is only required by some ISDN providers and not others.
Required Network Information
Four components are required by the network when sending CIC information. This information can be found in
the SETUP message.
(1) FEATURE (A statement advising the network that this is a feature based call, as opposed to a Service based
call).
(2) TYPE OF NETWORK ID (The PBX should send out NATIONAL for this information).
(3) NETWORK ID PLAN NUMBER  (The Interchange Carrier should be sent).
(4) NETWORK ID CHARACTER (XXX) (For AT&T the PBX sends out 288). 
						

							ND-45857 (E) CHAPTER 4
Page 105
Revision 3.0
SYSTEM DATA PROGRAMMING
NEAX2000 IVS Programming
Use the following programming to assign the ISDN PRI Call By Call Identification Codes.
CMA405 - 10 (dialed number) = 406 (go to table 406)
CMA406 - 288 (dialed number) = 010 (use route pattern 010)
CMA010 - 1 (1st choice) = 02010 (use LCR pattern 020 + trk route 10)
CM8A520 - 157 = 02 (Kind of called party = National)
CM8A520 - 158 = 01 (Called party Number Plan ID = ISDN / Telephony Numbering Plan)
CM8A520 - 159 = 02 (Type of Network ID = National)
CM8A520 - 160 = 01 (Network ID Plan Number = Interexchange Carrier)
CM8A520 - 161 = 288 (CIC code for AT&T)
CM8A520 - 162 = 0 (Feature)
The above programming will allow the 10288 to be sent out with the proper Setup message to the network. How-
ever, further LCR programming is required because the network will not understand what 10288 is as a dialed
number. Use the following LCR programming to delete the 10288 digits from being sent to the ISDN Network.
CM8A520 - 151 = 0 Allow digit deletion.
CM8A520 - 152 = 05 Delete the first five digits of the dialed number.
Note:This programming example only details the required steps for the 288 CIC. Each CIC must be programmed in different
tables to allow CM8A5XX - YYY = 161 to send out the unique CIC number to the network. 
						

							CHAPTER 4 ND-45857 (E)
Pag e 1 06
Revision 3.0
SYSTEM DATA PROGRAMMING
3.4.1 Call By Call Service Selection Assignment
DESCRIPTION DATA
Assign the kind of the called party number. • YYY=500-755 
(LCR/TR Pattern No. 000-255)
(1) 157 (Kind of Called Party No.)
(2) 01 : International
02 : National
03 : Network
04 : Local
05 : Not used
06 : Speed Dial
NONE :Not Sending
Assign the Called Party Numbering Plan Iden-
tifier.• YYY=500-755
(LCR/TR Pattern No. 000-255)
(1) 158
(Called Party Numbering Plan Identifier)
(2) 01 : ISDN/Telephone Numbering 
Plan
02 : Not used
03 : Data Numbering Plan
04 : Telex Numbering Plan
05 :
06 : Not used
07 :
08 : National Numbering Plan
09 : Private Numbering Plan
NONE : Not Sending
Assign the Type of Network ID Number. • YYY=500-755
(LCR/TR Pattern No. 000-255)
(1) 159 (Type of Network ID No.)
(2) 00 :
Type of Network ID No.
07 :
NONE : Not SendingCM8A
A START
~ 
						

							ND-45857 (E) CHAPTER 4
Page 107
Revision 3.0
SYSTEM DATA PROGRAMMING
DESCRIPTION DATA
Assign the Network ID Plan Number. • YYY=500-755 
(LCR/TR Pattern No. 000-255)
(1) 160 (Network ID Plan No.)
(2) 00 :
Network ID No.
15 :
NONE : Not Sending
Assign the Network ID Character. • YYY=500-755
(LCR/TR Pattern No. 000-255)
(1) 161 (Network ID Character)
(2) X :
X=0-9, A(*), B(#)
XXX :
Specify whether Call By Call is Feature or Ser-
vice.• YYY=500-755
(LCR/TR Pattern No. 000-255)
(1) 162 (Feature/Service)
(2) 0 : Feature
1 : Service
Assign the Binary Facility Coding Value. • YYY=500-755 
(LCR/TR Pattern No. 000-255)
(1) 163 (Binary Facility Coding Value)
(2) For AT&T
01 : SDN
02 : MEGACOM800
03 : MEGACOM
04 : Not used
05 : ACCUNET
06 : Not used
07 : Not used
08 : INTERNATIONAL800
16 : AT&T MULTIQUEST
NONE : Not Sending
For Nothern Telecom
01 : PRIVATE
02 : INWATS
03 : OUTWATS
04 : FOREIGN EXCHANGE (FX)
05 : TIE TRUNK (TIE)
NONE : Not SendingCM8A
B
A
~
~ 
						

							CHAPTER 4 ND-45857 (E)
Pag e 1 08
Revision 3.0
SYSTEM DATA PROGRAMMING
DESCRIPTION DATA
Assign the WATS Band Number. • YYY=500-755 
(LCR/TR Pattern No. 000-255)
(1) 164 (WATS Band No.)
(2) 00 :
WATS Band No.
09 :
NONE : Not SendingCM8A
B
END
~